The washing machine automatically drains water as soon as it enters the water, what is the problem?

Causes and solutions for automatic draining of the washing machine as soon as the water enters:

1. When washing clothes, hard items such as coins were not taken out, so that the hard items were stuck in the drain valve of the washing machine, causing water leakage. You can open the back cover of the washing machine, find the drain valve, and take out the hard objects in the drain valve;

2. It may be that the rubber ring inside the drain valve has been used for too long and is seriously worn. You need to replace the drain valve with a new one.

The washing machine is drained to the outside when it is added to the water discharge pipe, and the valve cannot be closed well. If you can't fix it yourself, you can only send it to a home appliance repair shop.

Once the washing machine is flooded, of course, it has an automatic drain pipe, and the water will flow out naturally, which is very convenient.

It can be overhauled as follows:

1. First of all, check whether the drain valve core is stuck in the power-off state, you can see whether the valve core rod is in place, otherwise the internal spring may be stuck, at this time, the valve cover should be unscrewed, check that there are foreign objects stuck or damaged, and should be overhauled or replaced.

2. If the drain valve is normal, check whether the drawbar of the tractor is in place, whether the drawbar is flexible to pull and return by hand, if there is a stuck phenomenon, it means that the inside of the tractor has been damaged and should be overhauled or replaced.

3. If the retractor is normal, whether the retractor has also acted in the state of water inlet when energized, and shake the drain valve core for drainage, which means that the computer board program has been disordered, and the computer board should be overhauled or replaced.

The reasons for the failure may be: 1. The driving circuit of the drain solenoid valve is abnormal, usually a two-way thyristor breakdown. 2. There is a foreign object stuck in the drain solenoid valve or its stroke.

The methods of identification are:

First turn off the power of the washing machine, and then manually add water with a bucket to see if there is water discharged from the drain pipe, if it is not discharged, it means that there is not a foreign object stuck in the solenoid valve, it is likely that the circuit is faulty. At the moment of power-on, you can also find clues by listening to whether there is electromagnetic noise or traction sound of the drain solenoid valve. Pay attention to the location of the inlet valve and the drain valve.

I think it may be that the automatic drain function of the washing machine is turned on, or the automatic drain function of the laundry is damaged, which will lead to the phenomenon of automatic draining as soon as the water enters.

If the washing machine automatically drains water into the washing machine, it may be that there is a fault inside the washing machine, and we can find the corresponding repair personnel to repair the washing machine.

The washing machine automatically drains as soon as the water enters the washing machine depends on what kind of washing machine it is, and the old-fashioned single-double-cylinder washing machine automatically drains the water as soon as the water enters is the problem of the drain switch. The new fully automatic washing machine automatically drains water as soon as it enters the water, which should be due to a problem with the water level sensor.

The automatic drain of the washing machine may be due to the fact that the drain valve is stuck by a foreign object, resulting in the drain valve not being closed; It may also be caused by the fact that the traction part of the drain valve is not completely homeed; Or maybe there is a malfunction in the drain solenoid valve, which causes the washing machine to drain automatically. If the washing machine is faulty, you can contact a professional during the warranty period.

The washing machine automatic drain may also be because we use it incorrectly, some washing machines need to put the drain pipe on a special hook to drain normally, if we put the drain pipe on the ground, there will be water in the washing machine.

It's the water level sensor that's wrong.

This happens because the drain valve of the washing machine is not closed or is not closed tightly.

When the automatic washing machine starts to fill water, it drains water while entering the water; At this time, the drain valve of the washing machine is not closed properly, and there is a problem or malfunction in the drainage system of the washing machine. At this time, you can check whether the retractor or solenoid of the drain valve of the washing machine is in a state of power loss and release.

In addition, in the drain valve of the washing machine, there are foreign objects or washing slag between the drain valve body and the drain valve core, so that the drain valve core is not closed tightly. It is recommended to contact the after-sales service department of the washing machine according to the model and brand of the washing machine for maintenance, and clean the drain valve.

Other common faults of washing machines.

1. Stop the water inflow when the water inflow does not reach the set water level.

This fault is mainly due to the poor performance of the water pressure switch, so that when the air pressure in the gas collection chamber has not reached the specified pressure, its contact will be changed from the open state to the closed state in advance and stop the water inlet, the specific cause and treatment method is:

1. The pre-compression amount of the water level control spring of the water pressure switch becomes smaller, as long as the adjusting screw is screwed in to increase the pre-compression of the water level control spring. If the water level control spring becomes less elastic or loses its elasticity, the water level control spring should be replaced.

2. The groove on the cam of the water pressure switch is worn or damaged, and the cam can generally be replaced to solve the problem.

2. The water inflow must exceed the set water level before the water inlet will be stopped.

This phenomenon shows that when the actual water level has reached the specified height, the air pressure in the gas collection chamber of the water pressure switch still does not reach the specified value, and the water pressure switch will only operate if the water level continues to rise. The specific reasons and ways to deal with them are:

1. The air conduction nozzle of the water pressure switch gas collection chamber is blocked or leaking. As long as the debris at the air nozzle is removed; Or seal it with 401 glue at the air leakage. If the air hose is aged, kinked, or cracked and leaking, the air hose should be replaced.

2. The pre-compression amount of the water level control spring of the water pressure switch is too large. Just unscrew out some of the adjusting screws to reduce the amount of precompression of the water level control spring.

3. The reversing push rod and transmission parts in the hydraulic pressure switch are deformed or damaged. It can be solved by repairing and correcting, and in severe cases, the water pressure switch should be replaced.

Answer 1, first check whether the drain valve spool is stuck in the power-off state, you can see whether the spool rod is in place, otherwise the internal spring may be stuck, at this time the valve cover should be unscrewed, check that there are foreign objects stuck or damaged, should be overhauled or replaced.

2. If the drain valve is normal, check whether the drawbar of the tractor is in place, whether the drawbar is flexible to pull and return by hand, if there is a stuck phenomenon, it means that the inside of the tractor has been damaged and should be overhauled or replaced.

3. If the retractor is normal, the retractor has also moved in the state of water inlet when energized, and shakes the drain valve core for drainage, which means that the computer board program has been disordered and the computer board should be replaced.

The drain solenoid valve is blocked by foreign matter, or it malfunctions. You can put down the washing machine and remove the drain pipe to see if there is any foreign matter at the drain valve port, if not, it may be that the solenoid valve is broken and needs to be repaired. It is also possible that the computer board is defective and cannot close the drain valve on this program.

A1The reason for this situation should be that the drain valve of the washing machine is not closed or closed loosely (there are foreign objects in the drain valve or the washing residue is stuck, resulting in the valve core is not tightly closed), and the drain valve needs to be disassembled for inspection and cleaning.

2.If you are not good at dealing with it, it is recommended to contact the after-sales service department of the washing machine according to the brand and model of the washing machine, and ask professionals to carry out maintenance inspections and troubleshooting.

Hope it helps.

Question: After draining the water to a high position, the water will be drained while entering the water.

As soon as the water pressure is high, it drains water.

Check whether the drain valve at the bottom is flexible? When confirming that the drain should not be drained, is the drain valve powered on, and if it is powered on, confirm whether the operation is wrong? If you don't look for a repair. If the power is not on, the water will leak, and the valve will be repaired.

It is necessary to distinguish between two types of models to illustrate:

Drum washing machine.

Generally, it is caused by the installation of drainage pipes in accordance with the requirements, and the drainage pipes must be arranged according to: washing machine drainage outlet - back buckle - drainage floor drain, and the drainage pipe is inverted U-shaped. As shown in Fig

What style? If the water level does not reach the level, it will definitely not enter the washing and rinsing process, if it is a wave turbine, the drainage while entering the water is caused by the drainage valve not closing normally, it may be that the motor is broken, the drainage valve may be bad, or foreign objects such as coins may fall into the drain valve and cannot be closed, and the technician needs to check that if it is a drum machine, it is generally a machine for drainage, and the drainage pipe needs to be hung high to a certain height. The lack of air in the floor drain will cause siphoning, and it should be no problem to re-hang the pipe after half an hour to enter the water.

If a fully automatic washing machine drains automatically as soon as water is in, there may be the following faults:

1.Clogged drains: Drains may become blocked, causing water to drain smoothly without socks. This may be due to dirt, fibers, etc., inside or outside the washing machine clogging the drain pipes.

2.Drain pump problem: The drain pump inside the boring washing machine may fail and cannot work properly. This could be due to a damaged drain pump, faulty circuitry, or connection issues.

3.Faulty water level control: There may be a problem with the water level control inside the washing machine that does not detect the water level correctly. This can cause the washing machine to drain automatically in the belief that the water level has reached the required level.

4.Control panel failure: The control panel of the washing machine may malfunction, causing an error signal to be sent for automatic drainage. This can be caused by a faulty circuit, a program error, or another control board issue.

5.Faulty sensors: Sensors inside the washing machine may malfunction and cannot properly detect water levels or water flows. This can cause the washing machine to start auto-drain incorrectly.

Summary: The automatic drain of a fully automatic washing machine as soon as the water enters may be caused by a clogged drain pipe, drain pump problem, water level control failure, control board failure, or sensor failure, etc. In order to determine the specific cause of the failure and the solution, it is recommended that you contact a professional maintenance personnel to overhaul or repair the washing machine.

If the washing machine drains automatically as soon as the drain enters the drain, it is usually caused by a malfunction in the drain system. Here are some of the reasons that can cause this malfunction:

1.Clogged drains can be caused by substances such as dirt, fibers, etc., that collect in the drains during washing.

2.Drain pump failure The drain pump may be damaged or malfunctioning due to dust excitation, which can cause the washing machine to not drain properly.

3.Drainage pipe installation problems If the height of the drainage pipe is incorrect or the installation method is wrong, it may cause the washing machine to fail to drain properly.

In order to solve the problem of automatic drainage of water entering the washing machine, the following measures can be taken:

1.Check the drain for blockages or other faults, and ask a professional to deal with them if necessary.

2.Check that the drain pump of the washing machine is working properly, and if it fails, it needs to be replaced and repaired.

3.Check that the drain is installed at the correct height and method, and reinstall the drain if necessary.

It should be noted that before solving the problem, you must first turn off the power and water inlet pipe of the washing machine to ensure your own safety. If you are not good at repairing, it is recommended that you ask a professional technician to help you solve the problem.

The fully automatic washing machine drains the water automatically as soon as it enters the drain pipe, and apparently, the drain valve has been opened.

Possible Reasons for Failure to Buried Filial Piety:

1. The driving circuit of the drain solenoid bending valve is abnormal, usually a two-way thyristor breakdown.

2. There is a foreign object stuck in the drain solenoid valve or its stroke.

Identification method: turn off the power of the washing machine, manually add water with a bucket, and see if there is water discharged from the drain pipe.

At the moment of power-on, you can also find clues by listening to whether there is a drain solenoid valve, electromagnetic noise or traction sound. Pay attention to the location of the inlet valve and the drain valve.

If the fully automatic washing machine automatically drains the water as soon as it enters the water, it may be that the drain pipe is faulty. In this case, the drain pipe may be clogged or improperly connected, causing the washing machine to not drain properly. In addition, it is also possible that there is a problem with the sensor or controller inside the washing machine and needs to be repaired by a professional technician.

It is recommended that when this situation occurs, contact the washing machine maintenance personnel in time for maintenance.

The washing machine keeps draining for the following reasons:

1. The cooling fan of the drainage pump of the washing machine is entangled by debris, so that the fan cannot rotate and prevents the rotation of the drainage pump;

2. The drainage pump is damp and rusty, resulting in the rotor not being able to rotate;

3. The impeller of the drainage pump is stuck by foreign objects and does not rotate. After inspection, the failure of the machine to drain is due to improper use, so that the coins and buttons fall into the cavity of the drainage pump, blocking the rotation of the impeller of the drainage pump, so the failure to drain the water is not possible. These three points are the reasons why common washing machines are always draining.

1. Check whether the drain filter on the lower right side of the washing machine is blocked by fluff and dirt, and if it is blocked, it should be cleaned up. Rotate the filter in a counterclockwise direction and gently pull it out, remove the fluff and dirt, wash it with water, and then put it in place and tighten it.

2. Check and clean the connecting pipe between the bellows and the drainage filter. The dirt in the connecting pipe between the filter and the washing machine drain pump and the drain pipeline should be removed to ensure that the drain pipeline is unblocked. Washing machines that use shaded pole drain pumps should check that the drain pump cooling fan is blocked.

Due to transportation or other reasons, the plastic cooling fan of the drain pump may be entangled or blocked by debris, making the fan unable to rotate and preventing the drain pump from turning.

3. Due to improper use, coins, buttons and other objects fall into the chamber of the drainage pump, blocking the rotation of the impeller of the drainage pump and making it unable to drain water. The impeller chamber cover of the drain pump can be opened and the foreign matter can be removed, and the fault can be eliminated.

4. Small pieces of clothing enter between the inner and outer cylinders and are pressed against the lower drain of the outer cylinder, blocking the drain opening. At this time, the back cover of the washing machine should be opened, the heater or bellows should be removed, and tweezers should be used.

Remove the laundry.

5. The drainage pump is damp and rusty, causing the rotor to fail to rotate, resulting in the drainage pump being unable to drain. Remove the drain pump, remove rust spots, add lubricant, and the fault can be eliminated.

6. Check whether the two wires of the washing machine drain pump are off, if the wires connected to the drain pump are intact, a multimeter should be used.

Measure the DC resistance of the drain pump.

7. The power supply voltage is too low, the drainage pump cannot be started, or the operation is weak, resulting in no drainage or slow drainage. Unplug the washing machine and measure the power supply voltage with a multimeter, if the voltage is lower than 187V, the drain pump will not work properly.