How to disassemble the radiator union and how to disassemble the radiator

How to disassemble the radiator joint, to clamp it with two answering pliers, the side to be dismantled to the left direction of the person to press down on the loose, slowly remove it.

1。In the disassembly of the radiator.

Before that, prepare a protective film to fully protect the removed radiator from being damaged by bumps. This is also the initial protection of the radiator.

2。In order to prevent the radiator from becoming unhot during later heating, it is necessary to seal the shut-off valve connected to the radiator before removing the radiator.

Prevent lime particles and wood chips from entering the main pipe, causing the main pipe plug.

3。When the radiator is displaced, look at the pipes of the main pipe. If it is PP-R aluminum-plastic pipe.

To be connected near the main pipe, the branch pipe is too far away, which will cause the heating to not be hot. If it is an aluminum-plastic composite pipe, if the pipe is not long enough to shift, part of the main pipe needs to be replaced, because there can be no interface underground. If the user chooses to add pipe fittings to the ground, it needs to be completed with the assistance of professional construction personnel.

4。When the radiator is moved away from the original place, it is necessary to pay attention not to injure other main pipes to avoid unnecessary economic losses.

5。The heating pipe should not be installed with too many joints, which will increase the flow resistance of the system in the pipe, resulting in the hydraulic imbalance and poor flow of the heating system and causing the radiator to not be hot.

6。After connecting the main pipeline, do a closed pressure test, the test pressure is times the working pressure, the test time is 30 minutes, and no leakage is qualified. At this point, the whole heating renovation process is over.

However, it needs to be reminded that after the heating is completed, the first heating period should ensure that there is a good heat dissipation space around the radiator, and at the same time take care of the heating facilities.

How to remove the radiator replacement?How to remove the radiator?How to remove the radiator, and the precautions for removing the radiator?

How to remove the radiator?How to remove the heating radiator?How to remove the radiator installation error?

Put the water first, drain the water in the radiator from the drain to prevent too much dirty water from staining the wall and floor when dismantling, and then use special tools to disassemble one by one.

1.At home, our first priority is to focus on safety. Place hanging radiators on load-bearing walls to avoid some safety hazards.

2.The radiator is placed under the window to prevent cold radiation and cold air circulation, and when people are close to the cold window, they will not feel the intrusion of cold air.

3.The radiator has a large amount of heat dissipation, especially the radiator itself, so you can't put furniture that is afraid of being heated for a long time nearby, otherwise unnecessary losses will occur.

First of all, make the necessary preparations before removing the radiator, one is the tool, the second is the location of the radiator, and the third is to prepare a container for receiving water to connect the residual water in the radiator. It is necessary to choose to remove it before filling with water, so it is usually more suitable in May-September.

Use a wrench to unscrew the joint of the pipe interface connecting the radiator, pay attention to keep the gaskets at both ends, and then use a plastic bag to seal the removed shut-off valve to prevent dust and foreign matter from entering the pipe and blocking the pipe after water injection.

Before removing the radiator, prepare the film containing the radiator, or other protective film, to prevent the radiator from bumping, damaging or peeling off the paint during the removal process.

If you do it yourself, you should pay attention to not touching other parts of the main pipe when moving the radiator away from the original position, so as not to cause damage, and when dislocating, do not install too many joints of the main pipe, so as not to increase the flow resistance, resulting in the heating is not hot. If you want to replace the radiator with a new one, you can also contact the installation and after-sales service of the new radiator, they can provide professional removal services.

Find someone to dismantle this, don't dismantle it yourself at home.

The detailed steps of the radiator removal tutorial mainly include the following steps:

1. Preparation. Before preparing to disassemble and install the radiator, you should prepare a protective film, which is mainly to provide comprehensive protection for the radiator that has been removed. Of course, this is only a relatively basic protection work, if you are not sure, you can choose to use foam and other tools to carry out the necessary protection.

Not only does it avoid possible wear and tear, but it also makes demolition safer.

2. Sealing work. Before the radiator can be removed, the shut-off valve connected to the radiator needs to be sealed. Its main purpose is to prevent problems such as radiators not heating that may be caused in the later heating period, and at the same time can effectively prevent lime particles and sawdust from entering the main pipeline, and thus cause problems such as blockage of the main pipeline.

3. Shift work. When moving the radiator, you need to pay attention to what kind of material the main pipe is made of. Different materials have very different requirements for pipe connections, so it is important to evaluate the location and distance of branch pipes and main pipes, as well as determine whether some main pipes need to be replaced, and whether there will be other effects on the heating.

If the work is more complex, the individual does not have enough capacity to complete it, and needs to be helped by a professional.

4. It should be noted that:

1) When the radiator moves away from the previous position, it must not affect other main pipes, otherwise it may damage the original structure and damage the facilities;

2) It is not good to use too many joints in the installation of heating pipes, otherwise it may affect the flow resistance in the pipes, and eventually cause the radiator to be not hot enough, affecting the normal life needs.

5. The last step of the dismantling work is to do a test to ensure that the radiator will not leak and the overall normal operation.

Installation attention. When installing radiators, you need to pay attention to the following three points:

1. When we plan to install the radiator, the first thing we need to do is where to install the radiator, which position has the best heating effect, which position has the best installation aesthetics, and of course, which position has the best safety performance.

2. In the process of installing radiators, the most important thing is safety sealing. Special attention should be paid to the fact that there are no water leaks. From another point of view, that is, the difficulty of construction, without special circumstances, do not change the position of the radiator at will, if this is the case, it will not only cause inconvenience to yourself, but also may cause inconvenience to others and neighbors.

3. The final stage, that is, after the radiator is installed, it is necessary to test and accept. Usually when replacing the construction, the workers will reserve the valve on the pipeline, and the stamping test should be carried out after installation. Make sure that there is no leakage, dripping, bubbling, or running water, and there is no problem with the installation of the radiator, which completes the test and acceptance of the radiator.

First put the water, drain the water in the radiator from the drain to prevent, when dismantling, there is too much dirty water to stain the wall and floor, and then use special tools to disassemble one by one, if you can't get it, finally ask a professional installation master to remove.

Summary. Dear, glad to answer for you! It is particularly easy to remove a radiator, because the general radiator is fixed by screws.

So if you want to remove it, you only need to loosen the screws at the upper and lower ends, but because it is in the form of a piece, the number of loose screws is relatively large, so you have to be patient. When you encounter a place that can't be twisted, you only need to apply a little lubricating oil.

Dear, glad to answer for you! It is particularly easy to remove a radiator, because the general radiator is fixed by screws. So if you want to remove it, you only need to loosen the screws at the upper and lower ends, but because it is in the form of a piece, the number of loose screws is relatively large, so you have to be patient.

When you encounter a place that can't be twisted, you only need to apply a little lubricating oil.

If it is a radiator that is formed at one time, you only need to apply a little lubricating oil to the two ends of its spindle, and then use a wrench to twist the fixed ends, and the radiator can be easily removed. Remember to let someone help carry the radiator after twisting it, otherwise the radiator will likely fall off suddenly after it is loosened, and it will not be good to hurt yourself, so you must pay attention to this!

The tandem heater wants to know how to dismantle a group! Hello, I am glad to answer for you<> a set of methods for dismantling the tandem heating are as follows: 1. Disassemble the old radiator:

First of all, we close the inlet and outlet valve (also known as the temperature control valve) in front of the radiator, and then use the nozzle pliers to remove the union between the radiator and the valve, which separates the radiator from the pipe, and then gently hold up the radiator by hand to remove the radiator; 2. Replace the new radiator: How to replace the new radiator? In fact, it is very simple, just reverse the steps to remove the radiator, here are two precautions:

1) The parameters such as the size and model of the radiator are the same as those of the original radiator, and the center distance of the radiator must remain unchanged if there are different situations; In addition, it is to see whether the place where the radiator is installed has requirements for the height and length of the radiator, and it is best not to be greater than the original radiator; 2) For the radiator material, it must remain the same, especially the original copper-aluminum composite radiator must not install steel radiator, because the copper-aluminum composite radiator is very corrosive, so most of the places where this radiator is installed have water quality problems, and we take the liberty of replacing it with steel radiator, which is easy to cause the service life of the radiator to be reduced and affect our normal heating. Tandem radiators can be removed individually. But if there is a problem with your radiator, it is better to disassemble and assemble the radiator at will without stupidity, and it is very dangerous to disassemble and assemble the radiator by yourself.

If you have to remove the radiator, it is recommended that you find a professional installer who can help solve the problem. Hope mine can help you <>

Do you have any other questions?

Summary. Radiator union disassembly**: Pro-radiator union disassembly** is as shown in the following figure: first saw and then rejected, you said how to remove the radiator plug and the steel pipe connection.

The old radiator has been used for a long time, and the steel pipe interface has rusted to death. If the pipe wrench can't be twisted, you can only look at the radiator plug to cut the steel pipe first, then extend the hand saw blade into the steel pipe, slowly open the steel pipe three to four petals, and then use a smaller flat shovel to remove the pipe.

Radiator union disassembly**: Pro-radiator union disassembly** is as shown in the following figure: first saw and then rejected, you said how to remove the radiator plug and the steel pipe connection. The old radiator has been used for a long time, and the steel pipe interface has rusted to death.

If the pipe wrench can't be twisted, you can only look at the radiator plug to cut the steel pipe first, then extend the hand saw blade into the steel pipe, slowly open the steel pipe three to four petals, and then use a smaller flat shovel to remove the pipe.

Enter the area and get the decoration for free**].

For northern residents, radiators are all too familiar. So here comes the question, do you know what the radiator removal tutorial is? What should be paid attention to when dismantling and modifying household radiators?

Let me give you a brief introduction. Radiator removal tutorial 1, before dismantling the radiator, you should prepare a protective film, so as to facilitate the removal of the radiator to do a good job of protective measures, so as to avoid bumps, damage and other phenomena. 2. In order to avoid the situation that the heating is not hot in the later stage, the shut-off valve should be sealed before the radiator is removed, so as to prevent lime particles and sawdust from flowing into the main pipeline and causing blockage.

3. During the shifting of the radiator, the pipe of the main pipeline should be looked at. If it is a PP-R aluminum-plastic pipe, it should be connected at the nearest place of the main pipeline, otherwise it will cause the heating to be not hot. If the user chooses to add pipe fittings to the ground, it should be completed by professional construction personnel on request.

4. Special attention is needed in the process of shifting the radiator, otherwise it will hurt other main pipelines and cause unnecessary losses. 5. During the installation of the heating pipeline, there should not be too many joints, otherwise it will increase the flow resistance in the pipeline, resulting in poor water flow and the radiator is not hot. 6. After the Lian clan shouted after receiving the main pipeline, the next thing to do was to suppress the experiment.

Under normal circumstances, the test pressure is to 2 times of the working pressure, the test time is not less than 30 minutes, and no seepage or leakage is qualified. What matters need to be paid attention to in the dismantling and modification of household radiators 1. In the process of removing radiators, we should change the pipes as little as possible, and ensure that the pipes are straight and can not be bent. If there are too many curved parts, it will cause too much resistance and affect the heating effect in the future.

2. In the process of dismantling the concurrent combustion pipeline, it should also be noted that the inner diameter should not be changed, otherwise it will lead to the phenomenon that the household radiator is not hot. 3. When you buy radiators or choose pipe products, you should go to a regular store to buy them. Summary:

After reading the above introduction, I believe you have a further understanding of the radiator removal tutorial. If you need to know more about it, please continue to ******, and more exciting content will be presented to you in the future.

Do the math how much it will cost you to renovate your home