How to change the protective film of the mobile phone, how to change the mobile phone film

Mobile phone screen protector replacement steps:

1. Tear off the original protective film and blow off the dust around the phone.

2. Use the fine soft bristle brush of the lens pen to brush off the large dust.

3. Wipe off the fine dust with a mirror cloth at the end, pay attention to gently wipe the mirror cloth from left to right three times, do not wipe back and forth, so that it is easy to move the dust left and right, and the result is still on the screen.

4. Start the film.

1) Tear off the first layer of secondary film (a layer of film to protect the film) of the protruding part, remember, do not completely tear off this layer of secondary film, tear a corner, and do not let the fitting surface be exposed to the air for a long time, easy to get dust.

2) Aim the side of the uncovered side to the screen and slowly attach it to the screen.

3) gently press and push with a credit card or a hard plastic sheet in the direction of the film, gently press and push in the direction of the film, the purpose of this is to ensure that there will be no bubbles in the process of filming, while pressing and pushing at the same time, while also observing whether there are bubbles in the part that has been laminated, once a bubble is found, it should be gently lifted, continue to operate after removing the dust, if it is completely pasted, and then find that there are bubbles, it is not easy to remedy.

5. After it is completely flattened, slowly tear off the second layer of secondary film on the surface. (If the screen of the model is sunken, you can use a strong adhesive transparent glue to glue it out.)

Take the toughened film as an example. Wipe the screen clean, take out the tempered film, align the hole above, put down the tempered film, press and hold the middle position with your hand, and press it flat.

First of all, you need to wipe the screen with a cloth or a soft fiber cloth to clean the phone screen thoroughly. After wiping it clean, you can compare the protective film you bought with the model, but don't tear off the release film yet. When you feel that your hand is more stable, you are tearing it open!

Observe the label on the protective film, tear off part of the release film, and be careful not to touch the adsorption layer of the protective film with your fingers. Align the adsorption layer of the protective film at the corners of the screen, making sure the position is aligned, and then apply it carefully. If bubbles are produced during the film process, you can pull the film back and re-apply it.

1. When sticking the film, first clean the mobile phone screen, you can use a wiping cloth and dust removal sticker to clean the stubborn dirt on the edge of the mobile phone and other parts, there is a protective film on both sides of the film, and the side with the date is facing up, there is no stickiness; The side without the date faces the screen and is sticky;

2. Use auxiliary tools to cut a small part of the vacuum film, paste it on the side without the date, and paste it by the edge, leaving a small section for easy removal;

3. Wipe the screen clean, tear off the side with the dust suction film, stick the protective film on the screen, press lightly, and squeeze out the bubbles;

4. Tear off the protective film with the date side, and the protective film will be pasted.

If you paste it yourself, go to sell the film there to report the mobile phone model, he will give you a screen-sized film, tear it off before when you take it home, wipe it clean with alcohol or screen cleaning liquid, and take out the top end of the film after it is completely dry, prepare a card in advance, smooth and do not swipe the screen, or increase the smoothness of a layer of paper on the bread, and use this card to catch up from top to bottom little by little after alignment, pay attention not to leave blistering, be careful, until the bottom is also aligned, and paste it in. Or if you think it's not good, take it to the film and let someone paste it for you! I wish you success ......

If you don't know how to do it, it's better to let someone who knows it change it for you, otherwise it's a waste.

This is a technical job, and the emphasis is on being fast, accurate, and ruthless, and it must be done in one go.

1. Place your phone on a stable desktop. Remove the phone cover or phone clasp from your phone.

2. Along the edge of the phone, gently buckle the corner of the tempering film with your fingernails. If you don't have nails, you can use the corners of toothpicks or plastic scissors instead, and after lifting the corners of the tempered film up, you can lift the tempered film in the direction of pasting.

3. If you can't fasten the corner of the tempering film, you can use a knife to insert the tempering film and insert it in parallel to avoid damaging the phone, and then slightly up until it blisters.

5. Then grasp the two corners with your fingers and pull them up, you can easily remove the tempered film.

In this way, the phone film has been removed.

OK. This is a mobile phone protector to prevent scratches on the screen of the mobile phone that has not yet arrived at the customer.

If it does not affect the use, it can also be removed, saving the trouble of re-applying the film.

If there is no problem with the protective film, it is not recommended to remove the protective film is mainly to protect the screen, if you want to disassemble, the general method is to find the edge first, and then use your fingernails or a harder card to draw between the protective film and the screen, you can separate the corner of the protective film, and then tear it off.