Does it affect the wrong connection of the inlet and return water of the natural gas wall hung boile

The inlet and return water of the wall-hung boiler of natural gas are connected incorrectly, and it will definitely have an impact. This is also prone to safety hazards.

There is an impact, after the wrong connection, it will not be able to play a good backwater effect, and the backwater will lose its original role.

The impact is great, and it is recommended to take it back. The wrong connection of inlet and return water will lead to water pollution, and it will be troublesome to repair later.

Influential.

The connection interface at the bottom is at least five pipes, plus the overflow pipe is a total of six pipes, each of which has a different function and is connected by the number. If the connection is wrong, there may be problems, damage to the wall-hung boiler, and even a greater safety hazard.

The wrong connection of these two pipes means that the return pipe of the heating system is connected to the heating water supply pipe on the wall-hung boiler, and the water supply pipe is connected to the return pipe of the wall-hung boiler. This leads to the reverse circulation of water flow throughout the heating cycle, which has a certain effect.

The water inlet switch under the wall-hung boiler should be turned off when it is usually in use, and only open when it is necessary to add water. As a heat source for independent heating in the home, the heating thermal efficiency of the wall-hung boiler can reach more than 90%, which is much higher than the thermal efficiency of using coal, oil, electric heating, air conditioning, etc. There is also no waste of heat loss and ineffective heat loss in boilers, pipes and other central heating boilers.

The wall-hung boiler is used for daily hot water bathing in the family, which is a modern form of bathing with constant temperature and large water volume. It is equivalent to a family bathing center, and its comfort and improvement of life quality are incomparable to ordinary water heaters, electric water heaters and solar hot water heaters.

Summary. It is okay for the water pipe of the wall-hung boiler to be higher than the wall-hung boiler, as long as the height of the floor heating pipe or radiator of the wall-hung boiler is lower than that of the wall-hung boiler.

Is it okay for the water supply and return pipe of the wall-hung boiler to be higher than the wall-hung boiler?

Hello dear, I am looking for exquisite answers for you here, please wait.

It is okay for the water pipe of the wall-hung boiler to be higher than the wall-hung boiler, as long as the height of the floor heating pipe or radiator of the wall-hung boiler is lower than that of the wall-hung boiler.

Some places are high, some places are low, is it okay, does it have any effect.

The water supply and return water are higher than the wall-hung boiler, what is the impact?

Dear, as long as you have heat, electricity or something with a relatively high temperature, it must be higher than your kind of tube.

Yes. The user installation operation is not standardized, the water inlet interface and the air intake interface are installed in reverse, during the test machine and use, the water flows into the natural gas pipeline, resulting in the water ingress of the natural gas pipeline, and when it is serious, all the supporting gas facilities and equipment in the community enter the water, and even the gas meter in the household will be damaged due to water ingress and cannot be used normally, resulting in a large area of gas outage for the surrounding users, bringing losses to the people's property, and there are potential safety hazards. In addition, in winter, once the water in the pipeline freezes, the drainage disposal time will be longer, which may cause damage to gas facilities and equipment.

Answer 1: When designing radiators, the upper water temperature is generally high, so there are fewer radiators, and the lower water temperature is low, and the radiators are more. After the hot water flows from the bottom up, the upper floors, which are originally hotter, become colder.

2. The hot water flows from top to bottom, the direction of the mechanical circulation force is consistent with the gravity circulation force, and the system is easy to balance. After the flow direction is changed, the original balance will be broken, which will cause some users to have insufficient heating. Because the backwater is used for water supply, there is no pressure, so the system does not circulate, and can only rely on the hot water kinetic energy on the backwater to push the system back little by little (in the northeast, it will cause the water not to go away, and it will be hot).

After the hot water flows from the bottom up, the upper floors, which are originally hotter, become colder.

The hot water flows from top to bottom, and the mechanical circulation force is in the same direction as the gravitational circulation force, and the system is easily balanced.

When the flow direction is changed, the original balance is broken, which will cause some users to lose heat.

Question: The two radiators in the living room are very hot, one bedroom and kitchen are not hot, the temperature is not high, the water inlet and the return water have been tried, and the water is not blocked, is it the reason for the wrong water inlet and return connection.

The answer may also be due to an imbalance in heating pressure; Because the heating water pressure is unbalanced, it will cause too much hot water inflow from the radiator in the living room, and the heating effect in the living room is good, while the hot water inflow of the radiator in the room is insufficient, and the heating in the bedroom is not hot. You can turn off the heating valve in the living room and open the heating valve in the bedroom completely.

This first depends on what kind of heater you have, if it is floor heating, then it will not be affected, but if it is a radiator, it will be difficult, because when people install radiators, the farther away and the higher.

Hello, this must have an impact, this is equivalent to a small boiler, the size of the water outlet and the return outlet, the upper and lower positions are not the same, and it will definitely not be hot if it is reversed.

It doesn't matter, because there is no water coming out if it is reversed, and the inlet and return pipes can be connected back in the correct way.

Summary. Hello dear, it is a pleasure to serve you. If the water supply pipe of the wall-hung boiler and the water outlet pipe of the bath are reversed, the following problems will occur:

1. First of all, the water supply pipe of the wall-hung boiler is reversed, which may cause the water in the water transmission system of the wall-hung boiler to not flow sufficiently, and there will be a phenomenon of leakage while water, that is, the water pressure will not reach the rated value. 2. In addition, the water outlet pipe of the bath will be connected to the reverse will lead to no hot water discharge, because the hot water in the water heater circulates in the pipe, so it is necessary to promote the flow of water, and at this time, the water is inward and can not come out, so there is no hot water out.

Hello. What happens if the water supply pipe of the wall-hung boiler and the bath outlet pipe are reversed?

Hello dear, it is a pleasure to serve you. If the water supply pipe of the wall-hung boiler and the water outlet pipe of the bath are reversed, the following problems will occur: 1. First of all, the water supply pipe of the wall-hung boiler is reversed, which may cause the water in the water transmission system of the wall-hung boiler to not flow sufficiently, and there will be a phenomenon of leakage while water, that is, the water pressure will not reach the rated value.

2. In addition, the water outlet pipe of the bath will be connected to the opposite will cause no hot water to drain out, because the hot water in the water heater circulates in the pipe, so it is necessary to promote the circulation of water in Dazhou, and at this time, the water is inward and can not come out, so there is no rolling hot water out.

will not damage the wall-hung boiler.

Hello, dear, no, you can pick it up again.

Is it a little hot to open the bath hose and some hot water is out?

It is normal that both hot and cold water have a certain flow in Kaizhou. If the amount of water is too large, you need to adjust the control valve to control the amount of water, so that the water supply pipe can maintain a certain pressure to avoid water leakage.

But the water replenishment valve can also be pressurized when it is opened, why?

Opening the water replenishment valve can increase the coarse content of the liquid, which increases the weight of the liquid and therefore the pressure. At the same time, hydration can make the structure of the stool in the stove system more compact, thus increasing the pressure.

But the hydration is connected to the bath tube.

In fact, this pipe should be pulled off temporarily, which is really unsafe, because it may cause other pipes to leak. The safest way is to disassemble the water pipe and connect the water replenishment device to the Linghe water pipe, so that it can be replenished, but because the water pipe is to be opened, it will bring a certain amount of noise to the water replenishment, which may be noisy.

Water ingress into the natural gas wall-hung boiler is a relatively common problem, because during use, due to a variety of reasons, it is easy to produce some water vapor and water droplets, which will lead to the phenomenon of water ingress when these water droplets enter the wall-hung boiler. If it is not dealt with in time, it will bring great damage to the wall-hung boiler, and it may also lead to dangerous situations such as **. So what should we do after discovering that the natural gas wall-hung boiler is flooded?

1.Power. After discovering that the natural gas wall-hung boiler is flooded, the first thing to do is to immediately cut off the power supply. Because the natural rental gas wall-hung boiler usually uses electronic ignition technology, if it is still in the energized state, it may cause an accident.

2.Drain. Open the water valve of the wall-hung boiler, and open the blowdown valve to discharge the water that enters the inside of the wall-hung boiler. When draining, it is best to use professional drainage tools, so that the water can be drained clean, and no dead corners will be left behind.

3.Examine. After draining, it is also necessary to inspect the inside of the natural gas wall-hung boiler to see if there is any leakage of pipes, valves and other components. If water leakage is found, it should be repaired and replaced in time so as not to affect the normal use of the wall-hung boiler.

4.Maintenance. In order to avoid the occurrence of water ingress into the natural gas wall-hung boiler, we also need to carry out regular maintenance.

For the wall-hung boiler that has not been used for a long time, it is necessary to check and clean the water valve and sewage valve to prevent moisture corrosion. At the same time, it is necessary to regularly replace the filter and other components of the wall-hung boiler to ensure the normal operation of the wall-hung boiler.

In short, the water ingress of natural gas wall-hung boiler is a relatively common problem, and we should deal with and repair it in time after discovering the water ingress phenomenon to avoid dangerous situations. In the usual use, it is also necessary to carry out regular maintenance and maintenance to ensure the normal operation of the wall-hung boiler.