The bathroom leaked and smashed the floor to repair it for 2 months, and then leaked, what s going o

To do waterproofing, you need to do it on the surface of the water, and you can do it yourself.

If the cement surface is waterproofed, use a super permeable waterproof guard to do waterproofing (if there are cracks, gaps and potholes on the cement surface, fill the complete with Meiding porcelain glue and then do waterproofing).

For the tile surface, first check whether the filling of the tile gap is complete (if the filling of the tile gap is incomplete, fill it with Meiding porcelain glue, and then use a stone tile waterproof guard to do waterproofing).

Exterior wall paint can be made waterproof with transparent waterproof repair adhesive.

The product will penetrate into the base layer and make the base layer waterproof. The product is recommended to be constructed in a dry place, the drier the base surface, the deeper the product can penetrate, if the base surface is full of moisture, high density, the material can not penetrate well. Regarding the principle of waterproof plugging, the source of water leakage is not blocked, and the water will only continue to penetrate into the wall, which will exist inside the wall for a long time, and will leak out from other parts of the wall when the water reaches a certain level.

The problem cannot be solved, and only by spraying waterproofing agent on the outside of the roof or exterior wall so that the water cannot penetrate into the wall and flow away can the problem be completely solved.

If the bathroom leaks and smashes the floor, it is troublesome enough and the cost is high. There is a way not to destroy the floor tiles, which household can be done from below, make a few holes under the bathroom at home, of course, it will not be opened, put the water-stopping needle in, and then use a high-pressure grouting machine to press the waterproof glue in. A water-stopping needle can spread over an area with a radius of 15 cm.

This kind of maintenance method is good, and the leakage in the bathroom is like this, and it can be maintained for many years without leakage.

The bathroom leaked downstairs, and then smashed the floor to find the leakage point on the water pipe, and after a few months, the downstairs began to drip again, and the floor of the bathroom was also wet, so the bathroom did not use water, and the ground was not wet after a while, but the wall began to be a little moldy, and the floor of other rooms began to arch up a little, urgently.

1. If the problem of water seepage in the bathroom is the waterproof layer of the ground, it can be repaired without smashing the floor, you can use strong transparent waterproof glue to pour it on the bathroom floor tile, which can form a colorless transparent waterproof film on the surface, and can also penetrate into the cement for waterproofing, 2. If it is a leakage caused by the upper and lower water pipes, it is generally necessary to smash the floor to solve it, because the water pipe is hidden under the floor.

What do I need to pay attention to when doing waterproofing in the bathroom? 1. Choose the right waterproof material.

Before doing waterproofing, it is necessary to choose the right waterproof material, if the waterproof material is not suitable, this will not only cause material waste, but also directly affect the waterproof effect. At the same time, we should also try to choose high-quality waterproof materials, so that the quality of the product is more guaranteed, and the service life is longer, while the inferior waterproof material stool is cheaper, but the service life is shorter, and it is easy to leak.

2. Do waterproof time.

When doing waterproofing, it is necessary to strictly follow the requirements and order of construction. Generally speaking, the waterproofing of the bathroom can only be carried out after the water and electricity are done, and if there is a plan to install floor heating at home, it can only be waterproofed after the installation of floor heating is completed.

3. The height of the wall waterproofing.

When doing waterproofing, it is not only necessary to treat the ground waterproof, but also to make the wall waterproof. If the wall is not waterproofed, then after the use of the long cherry blossom draft, the wall of the bathroom is prone to water seepage, mildew and other problems, which is easy to damage the sanitary ware of the bathroom, and will also harm the wall structure. Generally speaking, the waterproofing of the bathroom wall needs to be about one meter, which can play a certain role in protecting the wall.

What is the cause of water seeping into the next wall in the bathroom? 1. There is a problem with the quality of the waterproof material used, and the waterproofing has no effect, resulting in water seepage into the adjacent wall in the bathroom. In this case, it is recommended to re-do the waterproofing.

2. If the water pipe is leaking, we can turn off the faucet to see if the water meter is moving, if it is a water pipe leakage, then find the leakage point, and then repair it.

Bathroom in daily home life to assume an important function of the wheel, it can be said that even if there is no kitchen, it is necessary to set up a bathroom, so the bathroom can not be sloppy in decoration, especially in waterproofing, its water consumption is very large, if there is a water leakage problem, it is very likely to affect the use of the bathroom, most of the bathroom leakage needs to smash the floor to repair, so the bathroom water seepage does not smash the floor can be repaired? Let's take a look with Qeeka Home experts.

1. Can the bathroom be repaired without smashing the floor without smashing the water seepage?

If the problem of water seepage in the bathroom is the waterproof layer of the ground, it can be repaired without smashing the floor, you can use strong transparent waterproof glue, pour it on the bathroom floor tile, you can form a colorless transparent waterproof film on the surface, and it can also penetrate into the cement for waterproofing.

2. What are the causes of water seepage in the bathroom?

1. The ground tile gap is not treated tightly.

Most of the family bathrooms have water leakage, water seepage, etc., most of them are caused by the cracks in the ground tiles, and the treatment is not strict, etc., this is because these owners do not have the basic awareness of waterproofing, and do not understand that there are hidden sewer pipes under the tile gaps, but they think that the bathroom is waterproof.

2. The toilet squatting toilet is not tightly connected to the water inlet joint.

Generally, if the toilet is installed as a squatting toilet, its joint is buried under the tile, if the joint connection is not tight, the water will seep out at the moment of water release, and then slowly extend the wall of other functional areas through the cement mortar layer.

3. There are gaps in the floor drain and sewage pipes.

The floor drainage of the bathroom is realized through the floor drain, but if there is no matching between the floor drain and the sewage pipe during the decoration, it will lead to the water pipe connection is not tight, and there will be water seepage in the gaps.

Summary: The above is the introduction of the toilet seepage bureau water can be repaired without smashing the floor, I hope the content shared can give you some reference, if you want to know more about relevant knowledge, you can **** Qijia to consult.

If the bathroom water seepage is only caused by the water seepage on the surface of the floor tiles, it can be repaired immediately without smashing the floor. If it is the water on the surface of the floor tiles, such as the water that usually showers, or the water used to clean the floor through the gaps in the tiles, penetrates into the mortar layer under the floor tiles, and then leaks downward, we can clean the road surface, and clean the gaps in the tiles, the wall tiles and floor tiles need to be plugged with grout again, <>

Use a brush to paint all bathroom wall tiles with transparent waterproof penetrant twice, and you must brush evenly without missing brushes. Plug the odor-proof floor drain, and then pour the remaining transparent waterproof penetrant on the bathroom floor, carefully brush it with a brush, let it penetrate at will, and wait for the moisture-proof penetrant to penetrate into each gap of the floor tiles, which can generate a layer of high-density ground waterproofing very well to avoid water invasion, and it is necessary to pay attention to the edge and the surrounding area of the toilet also need to be brushed several times. Through this solution, the problem of surface water infiltration can be dealt with very well.

The first type is the leakage caused by the leakage of the pipes under the floor of the bathroom. In other words, there are water pipes or heating pipes under the pavement of our bathroom, and after a leak occurs, this kind of pipe will slowly penetrate into the pavement. In the end, it leads to the leakage and water seepage of the road surface of everyone's bathroom.

The second type is the water stored on the pavement of the bathroom, which leaks and seeps according to the corresponding cracks. That's also a situation that everyone usually uses the bathroom.

For example, when you take a bath in the overall shower room, there will be a lot of water on the ground, and if the road drainage pipes and moisture-proof of our bathroom are not very good, then this water is likely to seep into the road along the gap, causing water seepage on the roof of the bathroom. The factor in this situation is the problem of moisture protection in the bathroom. In fact, the toilet must find water seepage according to the effective order, gradually check, find the problem of water seepage, and then choose a good treatment method, so as to treat the symptoms, the effect is significant, and the damage can be reduced.

Today, Houjiang will talk about the proper inspection process, root causes and treatment methods of water seepage in the bathroom, and look forward to helping you to a certain extent.

Some can be repaired, this should be determined according to the specific situation, you can ask the master to determine the specific location, determine the specific maintenance plan.

If you don't smash the floor, it's not good to make up for it, because the water pipes in the bathroom are all under the floor, and if you don't smash the floor, you can't see which water pipe has a problem.

It can also be repaired without smashing the floor, in fact, you can lay another layer of cement on the floor, so that this can be avoided.

1. First of all, it is necessary to find out the water leakage point, and prescribe the right medicine according to the leakage situation.

2. If the tile has cracks and leaks, then we can use a professional caulk to refill the gap. After the caulk is dry, apply a waterproof layer, so that you can avoid the need to break the floor to repair the problem.

3. In the case that the water pipe is not broken, the dust, oil, stagnant water and so on on the surface can be cleaned to maintain the dryness of the ground, such as the tile joint is filled with caulk, you need to use a knife to draw a small groove, the tile joint, wall joint and other parts are sprayed with penetrating waterproofing agent, sprayed evenly, and when it is almost dry, fill the defective part with caulking paste.

Precautions. Note: After the waterproofing construction is completed, the waterproof material is required to be dry (usually after 24 hours) before it can be drenched.

Maybe the slope of the bathroom floor is too small, causing water to accumulate, but if the slope is reasonable, the water should flow into the floor drain, and without the water will not seep.

It's best to smash it, and do it all over again. If you don't want to smash it, you can find the leakage point, and then take the water to make up the gaps in the tiles without leaking, and then use waterproofing agent to brush both sides to keep them straight.

First of all, if there is water seepage, dampness, peeling and other situations in the bathroom, then it is generally caused by water leakage in the bathroom. The most important thing now is to find the cause of the leak

1. Find a professional hydropower worker to check whether the pipeline is ruptured and causes water leakage, etc., if it is a pipeline problem, it is necessary to repair the pipeline in time to solve the water leakage problem;

2. If there is no problem with the pipeline, then consider that the waterproof layer is not done well and cause water leakage, if the local water leakage is serious, it is recommended to do the waterproofing again, so as to fundamentally solve the problem.

Secondly, more than 80% of the leakage in the bathroom is concentrated in the yin and yang corners, pipes, sanitary ware, floor drains and other places, so it is recommended to use kitchen and bathroom waterproof slurry when doing waterproofing, first repair and strengthen these permeable parts, and then do waterproofing as a whole, so that the waterproof effect is better. However, remember to carry out standard construction according to the requirements during construction, so as to ensure a good waterproof effect.

Finally, I would like to add that whether it is a partial repair or a complete re-waterproofing, it is unrealistic not to smash the floor, and it is impossible to fundamentally solve the problem, so it is recommended to smash a part of the floor according to the actual situation.

It is necessary to smash the bricks, reapply them with a dust-repellent paint, and then lift them on the floor.

If it is still leaking after simple repairs, affecting the downstairs, and there is a dispute for a long time, then hurry up, find a worker, and smash it to renovate it.

It is necessary to determine whether the pipe inside the wall is leaking or the leakage is caused by waterproofing. If the water is waterproof and leaking, you should knock off the floor tiles and redo the waterproofing, and do a closed water experiment.

It depends on how far the leakage is, if it is not serious, find the leak and fill it, if it is serious, then you have to do it from scratch.

No, the general water pipe cannot be damaged inside the wall, but only the exposed interface is damaged, and there is no need to smash the floor.

No, you can use the plugging king and 902 glue.

The bathroom floor should be re-smashed to make it waterproof.

Remove all the floor tiles and cement sand in the bathroom, and then do waterproofing and use floor tiles.

No need to smash bricks! Now there is a waterproof, brush directly on the surface of the tile! I used it in Beijing.

If you want to deal with it well, you must smash the floor tiles, please adopt, do the task, thank you.

Smash it open and redo it waterproof. Or inspect the pipeline.

If the commode is leaking, use waterproof glue.

No need to smash, just use a leak preventer.

If you need to be sinned, it is better to find a professional.

Toilet. Cracks and leaks in the floor should be planed, and the waterproofing should be redone. in the inlaid tiles.

If it is your own home, if you want to completely solve it, you have to find someone to knock it off and redo the bottom layer waterproofing, generally with liquid asphalt and the like, if it is rented or a short solution, you can buy a bucket of spray, the tile gaps and corners of the wall are sprayed evenly and comprehensively. It is best to stop the bathroom first, open the window for ventilation for a few days, and let the moisture under the floor tiles volatilize to the maximum extent, and then do it. Pay attention to the brand and reviews, if it is not reliable, it is useless.