How many meters high should the waterproofing of the bathroom be? Why?

The waterproofing of the bathroom should probably be done at a height of meters.

According to national regulations, the waterproof height of the toilet is meters. However, the specific can be adjusted according to the actual situation, such as the bathroom area is only 4 square meters, the waterproof height is meters, such as the bathroom is 6 square meters, do dry and wet separation, the waterproof in the bathing room is meters, and the waterproof in other places only needs to be 50 cm, saving money and waterproof.

1. Why should the waterproof of the bathroom be meters?

Because after we level the bathroom, we also need a suspended ceiling, and if the waterproofing is too high, it will be wasted and become meaningless. If it is a dry area, the waterproof height should be at least 30 cm or more. If it is the shower area of the bathroom, then the waterproof height is generally about meters, because the position of the shower head in the bathroom is higher, and the height of the waterproof layer is controlled at about meters, which can well avoid the water sprayed by the shower from splashing on the wall, resulting in mildew on the wall.

If it is a non-shower area, the waterproofing of the bathroom wall can be meters. <>

Second, the waterproofing of the bathroom.

Waterproofing construction of toilets.

Make sure the site is clean, dry, and waterproof before the site.

It should be coated, no omission, firmly combined with the base layer, no cracks, no bubbles, and no falling off. The coating height is consistent, and the thickness should meet the requirements of the product. Brush twice with waterproof paint; Lay a protective layer.

In order to prevent the subsequent construction from damaging the waterproof layer, it is necessary to lay a protective layer on the surface of the waterproof coating. The protective layer should be completely covered with the waterproof layer, no omission, firmly combined with the base layer, no cracks, no bubbles, and no falling off; Closed water test.

During the closed water test, the water at the highest point of the ground should not be less than 2 cm, and it should be stored for at least 24 hours, and it will be qualified only after observing that there is no leakage. If there is a leak, it needs to be redone, and it must not be negligent; Grass-roots treatment, cleaning, and leveling.

Bonding layer, detail additional layer, acrylic.

Waterproof layer, water storage test.

Protective layer construction, secondary water storage test. <

3. Summary.

When we do bathroom waterproofing, choose materials suitable for our economic conditions according to the actual size of our bathroom, which saves money and can do a good job of waterproofing.

Just do it. If it is too high, it will waste materials and increase costs, and if it is too low, it may cause water seepage on the wall.

The waterproofing of the bathroom should be about two meters, because the possibility of leakage in the bathroom is very large, so the waterproof measures should be made firmer.

The general theoretical knowledge is like this: the kitchen and bathroom waterproof floor is all done, the upturn is thirty, and the shower is one meter eight. Remember that this is theoretical knowledge, just like the sand and cement ratio stipulated by the state, the official theory in China is the same as the news broadcast, you know.

The so-called waterproof is not your literal understanding of preventing water leakage, otherwise the effect of doing one meter eight and thirty centimeters and one centimeter is the same, and the most important and terrible thing is long-term moisture. To really treat waterproofing as waterproof, to play the role of not leaking and not wet, it is based on the specific house space, and each one is almost different.

When considering waterproofing in the bathroom, it is generally necessary to make the waterproof of the bathroom 1.5 meters high. Because the amount of water used in the bathroom is relatively large, the waterproofing should be made higher, so as to prevent water seepage on the wall. Only by making the bathroom waterproof more tight, so as to reduce the phenomenon of water leakage, there are many people when doing bathroom waterproofing, generally apply the price is more affordable, so as to cut corners.

Only consider waterproofing the bathroom, but you will find that the vast majority of developers do not do the waterproofing in the bathroom at all when building a house. <>

When doing the waterproofing of the bathroom, in order to be more safe, try to choose to do waterproof twice, so as to achieve a certain effect. If you choose to do only one waterproof from the best affordable ones, you will find that the effect of waterproofing is not achieved at all, and at the same time, you also need to fill the bathroom with water after doing waterproofing, and you need to observe the time for two days. Take a look at whether there will be water leakage downstairs, if there is a water leakage, it needs to be filled in time, to prevent the phenomenon of water leakage after the house is renovated, and then fill, which is very troublesome.

When making the height of the bathroom waterproof, you should know that the height of the waterproof should be as high as possible, not low, and the height of the waterproof should be higher, in fact, it will not have any impact on the house. However, if the waterproof surface is relatively low, the wall will be prone to fall off in the long run. Since most people use showers when taking a bath, and the height of the shower is generally more than 1.5 meters, in order to achieve a certain waterproof effect, try to choose a little higher.

As a layman, many people don't know what brand is best to use when decorating the waterproof material of the bathroom. Among them, you need to know too much to know about the decoration company.

What brand of waterproof material is used? When doing waterproofing and installing water and electricity in the home, don't try to be affordable, because there must be no good things in the cheap.

I think the waterproofing of the bathroom should be 1.5 meters high. This height is very good, which can prevent the problem of water seepage on the wall, and then this height can also strengthen the waterproofing, which is also very suitable.

It is appropriate to make a waterproof platform of 30 cm, or about 10 cm, depending on the height of the floor of the bathroom and the reasonable layout of the bathroom.

Generally, it should be meters high, because the whole wall should be waterproofed to prevent the stagnant water from penetrating the wall and falling off.

Bathroom waterproofing is divided into ground waterproofing and wall waterproofing, the waterproof layer should extend from the ground to the wall, 250mm higher than the ground According to the conventional bathroom by the shower head wall waterproof layer height shall not be less than 1800mm, the general thickness shall not be less than 1 5mm, and the waterproof project must be done 24 hours after the end of the water storage experiment.

Some decoration whites may not know much about the bathroom waterproofing is divided into ground waterproofing and wall waterproofing, but most insiders know that the general bathroom will only do 30 cm above the ground when doing waterproofing, and the shower area will be higher, according to the regulations is 1.8 meters. There is a basis for this.

If the non-shower toilet is waterproof in principle, it can be done, but in order to strengthen the waterproof effect, it can also be done uniformly, and the cost will not increase too much anyway, and it is more secure. If there are conditions at home, it is recommended to make a full height, and if it is close to the bedroom, it is recommended to make a full height against the wall of the bedroom.

Because the shower or sprinkler head at home is generally installed at the height. According to the height of our adults, if the waterproof is not high enough during decoration, long-term spraying is easy to wet the wall, resulting in mildew and starvation of the wall, and the loss of waterproof effect, so the waterproof of the shower and bathroom must not be lower than this height.

Summary. How high should the bathroom be waterproof? If you use a shower head installed with a concealed pipe, the wall should be brushed with a waterproof height of not less than the sprinkler head, not less than a meter.

If the area of the bathroom is relatively dry, this area only needs to reach 30 cm, if the bathroom is in the shower area, then the waterproof of the wall should be brushed at least to the meter, and the pipe of the floor around the bathtub, including the casing, should be more than 1 meter from the ground to the pipe. The wall surface that is not a load-bearing wall should also be waterproofed for the whole wall to prevent the water from returning to the tide and falling off, and the height is best left and right.

How high should the bathroom be waterproof?

How high should the bathroom be waterproof? If you use a shower head installed with a concealed pipe, the wall should be brushed with a waterproof height of not less than the sprinkler head, not less than a meter. If the area of the bathroom is relatively dry, this area only needs to reach 30 cm, if the bathroom is in the shower area, then the waterproof of the wall should be brushed at least to the meter, and the pipe of the floor around the bathtub, including the casing, should be more than 1 meter from the ground to the pipe.

The wall surface that is not a load-bearing wall should also be waterproofed for the whole wall to prevent the water from returning to the tide and falling off, and the height is best left and right.

The bathroom waterproofing is not done, do you smash the wall again to make the waterproof wall tiles fall off, if it is a load-bearing wall, can it be waterproof?

If you don't do it well, you're going to smash the wall.

If you smash the wall and redo the waterproof and re-paste the wall tiles, will they fall off after a long time?

Can load-bearing walls be brushed waterproof.

It will fall off after a long time, and this will have to be dealt with by a professional master.

It is recommended that the height of all wall waterproof brushes in the bathroom should not be less than the height of meters, and flexible waterproof brushing should be done, the combination of the ground and the wall is the most problematic place for waterproofing, and the waterproof painting in the bathroom must be done for no less than 24 hours!

When building a bathroom, in addition to the style and layout, you should also consider the issue of impermeability, as the bathroom is where the water consumption is the highest. Once something goes wrong, it can seriously affect life. SoHow high is the waterproofing of the bathroomThis?

What are the processes of waterproofing in the bathroom?

1. The height of the waterproof wall.

The impervious height of the bathroom walls is usually greater than 30 cm. If it is not the main wall supporting the load, the impervious height of the wall should ideally be meters or more, and the impervious height of the bathroom wall should be meters or more. The bathtub is about 30 cm high.

How high is the waterproofing of the bathroomwashbasin, waterproof height urinal.

The waterproof height of the basin wall should be 30 cm above the basin. If a toilet is installed, the waterproof height should be about one meter above the ground.

How high is the waterproofing of the bathroomThe waterproof height of the floor.

Waterproofing of the bathroom floor is the most important process in the entire project. The waterproofing height of the thinnest part of the bathroom floor should be about 2-3 cm, since the thickness of the impermeable layer directly affects the waterproofing effect, so when we are doing soil sealing, most of them are smoothed.

How high is the waterproofing of the bathroomWaterproof tile height.

In the structure of the bathroom, in addition to the impermeable layer in the floor, the surface of the wall where the floor comes into contact with the surrounding area must also be waterproof. The water-repellent coating here should be closed upwards, preferably about 25-30 cm above the ground.

5. The impervious height of the sewer.

The quality of the toilet sewer structure will have a direct impact on our quality of life. Therefore, in order to prevent the smell of the sewer from spilling into the floor drain, we must carry out waterproofing treatment near the drain pipe. The height of the culvert drain should be greater than 5 cm.

In addition, the surface of the walls and the joints of the water pipes must also be waterproof.

1. Before the waterproof construction of the bathroom, make sure that the bathroom environment is clean and dry, and then start to brush the first waterproof coating. When painting, it must be covered with a water-repellent coating without any omission, and the coating height must be kept constant. The thickness must meet the requirements of impermeability to ensure the bonding of the impermeable coating to the substrate.

2. After the first waterproof coating is dry, apply the waterproof coating for the second time. The interval should not be decisive, otherwise, the waterproofing effect will be affected. The specific interval must be determined according to the water-repellent coating used.

3. In order to avoid damage to the waterproof layer after construction, the protective layer should be placed on the surface of the waterproof coating after drying. The protective layer must cover every part of the waterproofing layer and must be left unmissed. After the completion of construction, a closed water test is required.

The water level at the highest point above ground must be greater than 2 cm. , you can get it for free

In home decoration, many projects are indispensable and cannot be ignored. Especially in terms of waterproofing in the bathroom, it must be done in place, so as not to bring a lot of trouble to your future life. In addition to paying attention to the waterproofing of the bathroom, do you know how high the waterproofing of the bathroom should be?

The following will be a detailed introduction to the celebration for everyone!

1. Ground height difference.

When making a waterproof bathroom, how much is the floor height difference? The floor elevation of the bathroom should be 20 30mm higher than the floor (including the ground on the first floor), and the actual height difference should be determined according to the ground construction practice, and be noted in the ground architectural design and floor structure design drawings after accounting.

Second, the waterproof material is made of rubber.

When choosing a waterproof material for the bathroom, don't be greedy for a temporary cheapness, otherwise it will bring trouble to your future life. The type of waterproof material in the toilet should meet the requirements of the construction drawings and the current relevant national standards. From the perspective of ensuring waterproof quality and convenient construction, toilet waterproofing should use polyurethane as raw material to coat film waterproof materials, try to avoid the use of membrane waterproof materials, in principle, do not use rigid waterproof practices.

3. Drainage method.

Regarding the drainage method of the bathroom, it is recommended to use the lower drainage method. At present, the sunken same-floor drainage (i.e., the drainage pipes are arranged in the sunken space and filled with slag or lightweight concrete) toilet design used in some projects has many problems in the construction and maintenance of the beam difference, and should be adopted cautiously. When there are special requirements (if you need to do the same layer drainage), you should make the correct waterproof structure design under the premise of complying with the waterproof principle.

Fourth, the back of the partition wall.

The rear partition wall of the bathroom is not recommended to use hygroscopic materials, such as aerated concrete, gypsum board, etc., and should use concrete blocks and other materials with good water resistance, and the root of the rear partition wall should be made of 100mm high strips with a strength grade of not less than C15 concrete, and the strips are the same width as the partition wall.

The above is the relevant content about how high the bathroom waterproof should be, I hope it can help you! Hunting network, China's well-known large-scale decoration square platform, decoration leading brand. If you want to put your mind on decoration design, it is recommended that you apply for the free design service of Hunting.com, and help you plan a reasonable space layout and exquisite design through the on-site measurement of professional designers.

Click here to get a free room measurement design by a professional designer.