How to repair a leaky urinal, what to do if the urinal leaks

1. Check whether the flush switch is reset. The plastic flush switch of some flush toilets has been worn for a long time, and occasionally there will be a phenomenon that it cannot be reset, if it cannot be reset, then it can be switched on and off several times, so that it can be reset. There is also to check whether the rubber gasket of the drain port under the ball valve is aging, the sealing is not tight, etc., and if the problem is found, it should be replaced, so as not to affect the use.

2. Check whether the connection between the spherical float of the water tank and the water inlet switch is loose, whether the float is in place and the switch is not closed, resulting in the water inlet does not stop, and the water flows out from the upright drain pipe after the water is full, in this case, as long as the connection between the float and the water valve switch is tightened. If the rubber ball valve of the toilet is damaged, the seal is not tight, and the toilet leaks, then it needs to be replaced immediately.

3. If the toilet tank is leaking, basically there is a problem with the drain valve, so it is necessary to check the rubber plug of the water tank outlet in time. If the rubber plug at the outlet is damaged or blocked by foreign objects, resulting in poor sealing of the rubber stopper, it will also cause the toilet to leak and flow water. If the water supply pipe in the tank is not placed correctly, it may also cause water leakage in the toilet.

Water leakage at the interface, which is the reason for the loose sealing.

Dry it with a hair dryer and seal it with glass glue.

It's also possible that the water pipes are blocked. It is best to seal it after dredging.

1. Remove the urinal, 2. Check the drain joint, check the sealing fittings, especially check the drainage joints inside the wall, 3. When the drainage pipe connection in the wall cannot be checked and determined, remove the drain joint, replace the new joint, and reinstall it to ensure that the seal does not leak.

Hello! Let's look at the problem of the pipe or the water valve, of course, you have to judge that you can replace the pipe or other components.

1. First of all, you need to find the cause of water leakage and see if the flushing switch has a water leakage problem. Sometimes, because this flush switch is plastic, it will not be able to be reset due to long-term wear. It is necessary to see if the rubber gasket has any aging problems, or if there is a tight seal, if so, it needs to be replaced in time before it can continue to be used.

2. Sometimes it is because the connection of the water inlet switch is loose, so it will lead to continuous water leakage. In this case, we first need to tighten the connection of the inlet valve switch. However, if the ball valve is not tightly sealed and has the problem of aging, it will also lead to water leakage, and it also needs to be replaced in time.

3. If there is a leak at the bottom, close the water inlet valve first and wipe the bottom of the urinal clean. Then prepare the glass glue to hit it, you can apply some fine seam glue to cover the glass glue. After it is completely dry, it can be burned to achieve the sealing effect, and then open the water inlet valve to see if there will be water leakage.

If the urinal is leaking, the first thing to do is to check that the flush switch is not turned off, and it will not leak again after turning the switch off. If it is a drain valve, use a screwdriver to open the drain valve, and replace and repair the bolts and parts in time. If the sewer pipe of the urinal is broken, be sure to find a professional to repair it.

The leakage of Benchang Hao Pool may be due to the fact that the flushing switch is stuck, resulting in the water tank has been flooding and leaking, it is recommended to check whether the flushing switch is turned off. The longer the urinal switch is used, the easier it is to get stuck, so turn it off when you usually use it so that the urinal does not leak.

If the urinal is leaking, it may be a problem with the drain valve, and if the drain valve is damaged, it will cause the urinal to leak. After opening the drain valve, check the parts of the drain valve one by one with a screwdriver, and replace the loose or damaged parts in time, so that the urinal will not leak after the new parts are screwed.

There is also a situation that there may be cracks in the water pipes installed in the sewers, or the water pipes are ruptured and cause water leakage. After the professional has replaced the water pipe in the sewer, it is necessary to redo the waterproofing of the bathroom so that there will be no more leaks.

1. Open the lid of the water tank first, try to lift the floating wall slowly, if the water in the tank stops flowing, it means that the float cannot reach the specified height, resulting in the valve plunger in the float valve. At this time, it is necessary to bend the floating wall slightly so that it is farther away from the tank wall.

2. If the float does not touch the water tank, you need to fix the float arm with one hand and remove the float with the other hand to see if there is water inside. After the water in the float is shaken dry, it is put back in its original position, and then the float rod is bent to the lowest place, which can effectively prevent new water from entering the tank.

3. If the above two methods do not work, you want to check the seat tank of the flush valve to see if it is blocked by the ball plug. It is important to know that the residue in the water is easy to accumulate at the bottom of the water tank, resulting in the ball game not being able to move normally, or the ball plug is damaged, resulting in the leakage of the flush valve.

1.Start by turning off the water source and draining the water tank. 2.

Check the inside of the tank for cracks or breaks, and replace the tank if necessary. 3.Check whether the accessories inside the water tank are loose or damaged, such as water valves, water pipes, water tank covers, etc., if they need to be replaced or tightened.

4.If the water valve is leaking, you can remove the water valve to clean it or replace the sealing ring. 5.

If the water pipe is leaking, it can be repaired with tape or sealant. 6.If the water tank cover is leaking, you can replace the sealing ring or repair it with sealant.

7.After the repair is completed, the car stop re-opens the water source to check whether there is any leakage.

Enter the area and get the decoration for free**].

Nowadays, most families have begun to use toilets, but for the elderly, it is better to choose a safer toilet, we know that no matter what things are used for a long time, there will be some failures, so this time is to repair. Let's introduce to you how to fix a leak in the toilet cistern. How to repair the leakage of the toilet cistern 1, for the problem of the material of the water tank, the best solution is to separate the toilet tank, one by one to check whether the parts in the toilet tank are in good condition, if there are some parts broken, can be repaired, it is best to replace it if it cannot be repaired, if it is too inferior to the pumping tank, it is more rotten, it is recommended to replace the entire water tank, so as not to bring more serious consequences.

2. The solution to the problem of the toilet sewer pipe is to carefully check the interface between the toilet and the sewer pipe, whether it is loose, or the pipe is rotten, at this time, if the pipe is rotten, it is necessary to replace the pipe again, if it is, it is not connected, you need to use some wire or the like from the outside to buy some materials that can fix it, and fix it well. 3. For the problem of the drain valve of the toilet, this is a bit complicated, because it is designed to be tested with many professional tools, it is recommended to ask the workers who repair the toilet to carry out professional maintenance, which also ensures the normal use of the toilet. How to clean the toilet cistern 1, use the toilet cleaner to clean, we need to put the toilet cleaner in the toilet tank, the toilet cleaner sold on the market contains a variety of functional ingredients to remove impurities and odors in the toilet, and secondly, the toilet cleaner generally has a fragrant smell, so we only need to press the button to flush the toilet, and the blue water will be released, this water can not only remove the stolen goods after the toilet is very clean, it can also effectively keep the water tank clean.

2. Use hot and cold water alternately to clean the toilet reservoir, generally speaking, there will be dirt in the toilet reservoir, for the inside of the water tank is mainly to use the toilet cleaning treasure to clean, not only with water blisters, but also need to use a rag to wipe, after wiping, you can put some hot water into it at this time, you can eliminate the dirt attached to the water tank, to achieve the purpose of cleaning the water tank. In addition, the used water in the tank can also be used to flush the toilet. Do not use the inside of the toilet cleaner to clean the inside of the water tank.

3. You can use vinegar to clean the toilet cistern, and you can put in an appropriate amount of vinegar: Vinegar has the function of disinfection and sterilization, but the vinegar here not only has the function of disinfection and sterilization, but also it can remove the scale attached to the inner wall of the water tank, because the vinegar and scale are mutually neutralizing the functional effect, which can make the inner wall of the water tank more white and bright, but the vinegar only needs to be put in an appropriate amount, not too much. Summary:

The relevant content on how to repair the leakage of the toilet cistern is introduced here, which depends on what causes the leakage of your cistern, and repair it according to the cause. I hope the above introduction is helpful to you.

Do the math how much it will cost you to renovate your home