Urinal leakage, what to do How to repair a urinal leak

The delay valve can't be closed, and it may be good to disassemble and clean it up, but it's too professional for ordinary people to dismantle it. Let's find a master.

This can be pulped to try, or you can repair the waterproof place.

1. Check whether the flush switch is reset. The plastic flush switch of some flush toilets has been worn for a long time, and occasionally there will be a phenomenon that it cannot be reset, if it cannot be reset, then it can be switched on and off several times, so that it can be reset. There is also to check whether the rubber gasket of the drain port under the ball valve is aging, the sealing is not tight, etc., and if the problem is found, it should be replaced, so as not to affect the use.

2. Check whether the connection between the spherical float of the water tank and the water inlet switch is loose, whether the float is in place and the switch is not closed, resulting in the water inlet does not stop, and the water flows out from the upright drain pipe after the water is full, in this case, as long as the connection between the float and the water valve switch is tightened. If the rubber ball valve of the toilet is damaged, the seal is not tight, and the toilet leaks, then it needs to be replaced immediately.

3. If the toilet tank is leaking, basically there is a problem with the drain valve, so it is necessary to check the rubber plug of the water tank outlet in time. If the rubber plug at the outlet is damaged or blocked by foreign objects, resulting in poor sealing of the rubber stopper, it will also cause the toilet to leak and flow water. If the water supply pipe in the tank is not placed correctly, it may also cause water leakage in the toilet.

Water leakage at the interface, which is the reason for the loose sealing.

Dry it with a hair dryer and seal it with glass glue.

It's also possible that the water pipes are blocked. It is best to seal it after dredging.

1. Remove the urinal, 2. Check the drain joint, check the sealing fittings, especially check the drainage joints inside the wall, 3. When the drainage pipe connection in the wall cannot be checked and determined, remove the drain joint, replace the new joint, and reinstall it to ensure that the seal does not leak.

1. First of all, you need to find the cause of water leakage and see if the flushing switch has a water leakage problem. Sometimes, because this flush switch is plastic, it will not be able to be reset due to long-term wear. It is necessary to see if the rubber gasket has any aging problems, or if there is a tight seal, if so, it needs to be replaced in time before it can continue to be used.

2. Sometimes it is because the connection of the water inlet switch is loose, so it will lead to continuous water leakage. In this case, we first need to tighten the connection of the inlet valve switch. However, if the ball valve is not tightly sealed and has the problem of aging, it will also lead to water leakage, and it also needs to be replaced in time.

3. If there is a leak at the bottom, close the water inlet valve first and wipe the bottom of the urinal clean. Then prepare the glass glue to hit it, you can apply some fine seam glue to cover the glass glue. After it is completely dry, it can be burned to achieve the sealing effect, and then open the water inlet valve to see if there will be water leakage.

If the urinal is leaking, the first thing to do is to check that the flush switch is not turned off, and it will not leak again after turning the switch off. If it is a drain valve, use a screwdriver to open the drain valve, and replace and repair the bolts and parts in time. If the sewer pipe of the urinal is broken, be sure to find a professional to repair it.

The leakage of Benchang Hao Pool may be due to the fact that the flushing switch is stuck, resulting in the water tank has been flooding and leaking, it is recommended to check whether the flushing switch is turned off. The longer the urinal switch is used, the easier it is to get stuck, so turn it off when you usually use it so that the urinal does not leak.

If the urinal is leaking, it may be a problem with the drain valve, and if the drain valve is damaged, it will cause the urinal to leak. After opening the drain valve, check the parts of the drain valve one by one with a screwdriver, and replace the loose or damaged parts in time, so that the urinal will not leak after the new parts are screwed.

There is also a situation that there may be cracks in the water pipes installed in the sewers, or the water pipes are ruptured and cause water leakage. After the professional has replaced the water pipe in the sewer, it is necessary to redo the waterproofing of the bathroom so that there will be no more leaks.

The sink is an indispensable living utensil for the family, and it is inseparable from the daily laundry and washing of vegetables. However, if the quality of the pool is not good, there will be water seepage, which will bring great trouble to our daily life, so how to deal with the leakage of the pool? Let's take a look!

How to deal with pool leakage:

1. Surface repair method.

During the construction of the pool, the muddy water is not poured tightly, and the whole is a little deviated from the pockmark, and the water leakage will be formed after long-term water erosion and the waterstop is not fixed. At this time, we can use film materials (such as epoxy resin or resin-impregnated glass cloth) to lay along the surface of the cracks, especially for the vegetable washing basin, we must use non-toxic, non-polluting environmentally friendly materials.

2. Filling method.

If there is a large area of water seepage on the bottom plate of the pool, this should be a crack around the pool, such as a V-shaped or U-shaped groove on the surface, assuming that the crack is too wide, it is recommended to use resin mortar material for filling, or use impermeable mortar or asphalt and other materials to reinforce. After treatment, you need to wait for 7 hours before use, otherwise the filler material will fail.

3. Injection method.

Now people are accustomed to divide the whole porcelain plate into many pieces for bonding into a pool, and it is necessary to construct several blocks during construction, rather than the overall construction, so it is easy to form gaps. If the crack is small, the coarse mass can first set the injection pipe at the crack, and then inject the repair material into the concrete, and then seal it with surface treatment.

Summary: The above is the relevant problems of how to deal with pool leakage introduced to you, I hope to help friends in need. The pool seepage is also divided into several situations, and the methods used in different situations are also different, of course, when repairing the pool, the materials also need to be paid attention to.

The phenomenon of pool leakage is encountered by many families, which makes many owners feel very irritated but helpless. I'm going to share some with you today.

There are several types of pool leaks.

1. The water seepage form of the construction joint. Because during the construction, people are accustomed to artificially dividing the whole ground into many blocks, and the construction will be carried out according to several blocks during the construction, rather than the overall construction, so this leads to the appearance of gaps after the construction is completed.

2. A large area of water seepage is in a state of jujube. Large-scale water seepage generally occurs in the bottom plate, the main reason is that the foundation pit precipitation around the base surface should be below the cushion, because its Dahu trace is not at the due level, so it causes poor drainage, the foundation pit water level **, flooded the cushion, does not have the conditions for pouring concrete, but at this time in order to achieve a certain project progress, carried out the construction with water.

3. The seepage macro of the wall pipe is dismantled. There are also various pipes in underwater engineering, such as air ducts, water pipes, electric pipes, etc., which are not densely connected with the main pipe, and their welds are flawed.

4. The water seepage form of the deformation joint. Because the waterstop is not fixed very firmly, and the concrete is not tightly pounded and compacted, the whole will deviate from the center, resulting in the appearance of numbness on the surface of the object, and then through the erosion of water, this situation will become more and more serious.

How to deal with pool leakage:

1. Drainage, check whether the drainage is smooth and drain away the stagnant water from the intersection of the tile, skylight, chimney, exhaust air and tile.

2. Block the water, find the leakage point on the auxiliary waterproof layer, repair the waterproof layer and block the water.

3. Water diversion, which is the most inferior practice, that is to say, a method used only when the water leakage point cannot be found, and the water accumulated in the insulation layer is led to the outside, and the specific methods are as follows

4. Remove the tile, smash the protective layer, remove the waterproof layer, and level the leveling layer, mark the exposed insulation layer and mark the water-filled part, and then remove the insulation layer and clean it up.

5. Find out the leakage point on the clean concrete slab, block it with waterproof treasure material, and then make a waterproof layer on the large surface, set up a drainage outlet at the marked place, and then backfill and level.

6. The center of gravity should be waterproofed, and it should be lapped with the original waterproof layer, and the protective layer should be installed with tiles and the site should be cleaned up.

The method of grouting and plugging leakage is adopted. The steps are as follows: firstly, the grouting hole is designed, and the location of the grouting hole should be so that the hole and the leakage crack pores intersect, and select the place with the largest water leakage.

Secondly, a number of holes are grunted, and their positions need to be reasonably arranged according to the water leakage, for the purpose of deriving water leakage, and holes are arranged at the concentrated water leakage, and the hole spacing is large if the crack is large, and the hole spacing is small if the crack is small. The next step is grouting. Vertical cracks are generally bottom-up, and horizontal cracks are grouting from one end to the other.

First, the specific operation method of grouting.

1. Design the grouting hole, and the location of the grouting hole should intersect the hole and the leakage crack pores, and select the place with the largest water leakage.

2. Grouting a number of holes, the position of which needs to be reasonably arranged according to the leakage situation before the collision, for the purpose of deriving water leakage, in the concentrated water leakage of holes, large cracks are large hole spacing, small seams are small hole spacing.

3. Carry out grouting. Vertical cracks are generally bottom-up, and horizontal cracks are grouting from one end to the other.

4. The final plugging is completed.

2. What should I do if the overflow of the kitchen sink leaks?

1. Water leakage at the faucet joint and damage to the water-stopping tape. If it's broken, you won't be able to secure the faucet fixing screws.

Method: Tie the faucet tightly first, turn it counterclockwise with a wrench to remove the faucet; Turn the threaded hole outward and wrap the seal tape five or six times on the screw print; After checking, tie it in with pliers in the direction of the clock; Once the installation is complete, turn on the main switch to confirm if there is still water leakage.

2. Leakage of the overflow hole of the sink; The shaft gasket inside the sink is damaged.

Method: Replace the shaft pad. Use pliers to rotate the gland, and then use the clamp to remove the damaged shaft gasket and replace it with a new one.

3. The cap-type nut of the faucet is loose.

Method: Re-tighten the cap-type nut.

4. Caused by the wear of the triangular gasket in the gland.

Method: Rotate the screws of the faucet with a tool, remove the screws and tie head after loosening, and then loosen the gland and remove it, then take out the triangular gasket in the gland and replace it with a new triangular gasket.

5. The sewer is blocked and leaking.

Method: Remove debris.

6. The water pipe is aging, the seal is not in place, and the water leaks.

Method: Replace the hardware.

3. What should I do if the swimming pool leaks?

1. If the old tiles fall off is not serious, and the surface is smooth, the waterproof adhesive film can be directly paved at this time, but for the service life of the waterproof adhesive film, it is recommended to knock off all the old tiles and then pave;

2. If the swimming pool using waterproof adhesive film has water leakage, you can drain the water in the swimming pool first, and after the waterproof adhesive film of the swimming pool is dry, check the welding place of the waterproof adhesive film and re-weld the cracked part;

4. If the swimming pool film is damaged and leaks coarse water, re-weld the new waterproof film on the damaged swimming pool waterproof film, and wait for 24 hours to dry, and then release the water for acceptance. The construction period of the standard swimming and cleaning pool is two days, and it can be waterproof and accepted after 24 hours of dry glue.