How to maintain the cutting board so that it is not easy to crack?

Apply it with cooking oil to maintain it without cracking, and the method is as follows:

1. First of all, rinse the cutting board to remove dust and other dirt on the surface.

2. After cleaning, put it in a cool and ventilated place to dry the water.

3. Then prepare some cooking oil, we apply it evenly on the cutting board, in order to avoid dirty, put a layer of film under the cutting board.

4. After brushing the first side, change to the other side, and brush evenly. Because the oil is highly penetrating and volatile, it can moisten the wood for a long time, so the cutting board is durable and not easy to burst or decay.

Until the oil enters the wood for three minutes, and it can be saturated. Once the oil is treated, no matter how long it takes, the cutting board will not crack.

Solid wood occupies the board, two wooden strips on the reverse side, and two wounds will not crack, and the sun exposure will not be listed.

Don't be in a hurry to use the newly bought cutting board, teach you the correct maintenance method, use it for a long time without mildew or cracking, the method of maintaining the bamboo cutting board, the cleaning method of the newly bought cutting board, the tips for maintaining the cutting board, kitchen supplies, life tips, welcome to pay attention to the magic trick life workshop, thank you!

Here's how to remedy a cracked cutting board:

1. For the newly bought wooden cutting board, apply both sides and sides of the wooden cutting board with cooking oil before use, dry it, and then apply it repeatedly.

Two or three times. After this treatment, the wooden cutting board is not easy to crack.

2. For the newly bought wooden cutting board, soak the wooden cutting board in concentrated salt water for more than 24 hours before use, and then let it dry. After this treatment, the wooden cutting board is not easy to crack.

3. For the newly bought round wooden cutting board, open a small groove in the middle of the side of the wooden cutting board before use, and tighten the hoop with thick iron wire (you can also use the iron sheet to tighten the hoop, and you can not groove it when using the iron sheet). Wooden cutting boards are less prone to cracking.

4. If the wooden cutting board is cracked after use, you can soak the wooden cutting board in water, and the cracks will slowly shrink, and then use iron sheet or wire to wrap around the outer side of the hoop after it shrinks to a small crack.

5. Pay attention to maintenance after using the wooden cutting board, clean the cutting board after use, and then use a thick cloth to wet it and spread it on the wooden cutting board to keep the wood cutting board moisture to prevent cracking.

6. In addition to paying attention to maintenance, the wooden cutting board should not be exposed to the sun to prevent the wooden cutting board from cracking. At present, the cutting boards that can be seen are mainly made of bamboo and wood, and these two materials are also the most favorite cutting boards in life.

7. However, the cutting board can not be used immediately after being bought, so the newly bought bamboo and wood cutting board still needs to be reasonably processed to ensure the stability of its subsequent use performance and the long service life.

Summary. Dear, hello, the cutting board is always cracked and the treatment method is as follows: 1. After each use, wash it and put it in the water basin to invade, and then pick it up and wash it before use.

2. After buying back a new cutting board, it should be coated with cooking oil or lard immediately. 3. Let the cutting board be fully wet, reduce the cracks, and then use iron sheets or wires to wrap around the outside of the hoop after shrinking to a small crack. 4. Use fresh meat skins to nail them on both sides of the crack on the side of the cutting board.

Dear, hello, the cutting board is always cracked and the treatment method is as follows: 1. After each use, wash it and put it in the water basin to invade, and then pick it up and wash it before use. 2. After buying back a new cutting board, it should be coated with cooking oil or lard immediately.

3. Let the cutting board be fully wet, reduce the cracks, and then use iron sheets or wires to wrap around the outside of the hoop after shrinking to a small crack. 4. Use fresh meat skins to nail them on both sides of the crack on the side of the cutting board.

Many people have the experience of cracking after buying a cutting board, but many people are complaining about buying a fake cutting board, in fact, in fact, there is only one reason for the cracking of the cutting board is too dry, causing the internal stress change of the wood, so it produces cracking, these are the laws of nature, as long as we know the cause of the cracking of the cutting board, it is not difficult to prevent cracking, and if the new cutting board is not used after the packaging, there is no way to replenish the water, and it will definitely crack after the lack of water.

The main effect of using oil to infiltrate the soaking is to make the wood more resistant to corrosion, and also make the wooden cutting board more resilient and lubricate the cutting board, but in a too dry environment, the oil in the cutting board cannot be satisfied, so it will also crack.

The newly bought cutting board should be scalded with boiling water first, and then soaked in concentrated salt water for a day, concentrated salt water is to boil the water while it is hot, and add it until it is no longer melted, the purpose of using it to soak a new cutting board is to make the surface of the wood with salt, which can prevent the wood from cracking when dry.

01 Or after heating a pot of oil, wait for it to cool to about 70 degrees, apply it to the surface of the cutting board, stand for a while, apply it a few more times, wipe the oil dry with a kitchen paper towel, and then use.

02 First of all, rinse the cutting board and remove dirt and other dirt from the surface.

03 After cleaning, put the cutting board in a cool and ventilated place to dry the moisture of the cutting board, and it must be dried.

04 Prepare some hot cooking oil, preferably vegetable oil, spread it evenly on the new cutting board, in order to avoid dirty cutting boards, you can put something under the cutting board, such as plastic wrap or plastic paper.

05 When brushing the oil, both sides should be brushed evenly, the penetration of the oil to the wood is relatively strong, and it is not easy to volatilize, which can achieve the purpose of long-term maintenance of the cutting board, and it will be more durable, not easy to decay and crack. When brushing the oil, you should brush it several times until it is saturated.

The method of mildew prevention and non-cracking of the new cutting board:

1. First of all, disassemble the newly bought cutting board, scald it with hot water, and remove the wax on the new cutting board. Because the manufacturer will apply a layer of wax on the cutting board when leaving the factory to prevent the cutting board from cracking.

<>2. Then put the cutting board in the dishwashing sink, pour in 100 grams of edible salt, and fill it with hot water, and let the cutting board soak in the salt water for 2 hours. Salt is added here to set the color of the cutting board.

<>3. After soaking, take out the cutting board and dry it in a cool place.

<>4. Finally, pour some cooking oil into the cutting board, apply it to the cutting board, and then place it in a cool place to dry, and repeat the operation 3-4 times. After this treatment, the new cutting board will not become moldy or cracked.

1. Place the cutting board flat on the stand. Apply vegetable oil on both sides, dry and then apply again and again until the vegetable oil enters the wood for three points and reaches a saturated state. For several days on end, the fuel consumption depends on the size of the cutting board, and generally only costs more than 250 grams.

After being treated with vegetable oil, the cutting board will not crack no matter how long it takes.

2. First scald with boiling water, wash off the outer layer of wax, after washing off, be sure to soak in concentrated salt water for a day, concentrated salt water is to boil the water, add salt while hot, and add until it no longer dissolves.

The purpose of soaking in concentrated salt water for a day is to make the surface of the wood salty, which absorbs moisture and prevents the wood from drying and cracking.

After soaking, take it out, heat a pot of oil, wait until it cools to about 70 degrees, apply the surface of the cutting board, let it stand for a while, and then apply it again, several more times.

When the oil is almost absorbed, wipe the oil dry with paper and the cutting board is ready to use.