After three years of moving into a new house, the bathroom suddenly leaks, how to solve it?

There are generally only two major reasons for toilet leakage, one is pipe leakage, and the other is the failure of the waterproof layer and water leakage. Judging what kind of cause of water leakage, usually use the elimination method, especially the water inlet pipe is always water, if the water is suspended or the water is not spilled to the ground, the water leakage problem is solved or greatly reduced, this is usually the problem of the failure of the waterproof layer, on the contrary, the water pipe has a problem. If there is a problem with the water pipe, it needs to be replaced by smashing the tiles, the waterproof layer will be destroyed, and the vibration may affect the quality of the floor slab, so the waterproof layer should also be redone with appropriate materials.

There are two options for the maintenance of water leakage caused by the failure of the simple waterproof layer: one is to smash the tile and redo the waterproof layer, and the other is to use the transparent waterproof paint without smashing the bricks to paint on the surface of the tile, which is costly, and the disadvantage is that due to the thin coating, it is difficult to do it once and for all, and it may need to be repaired in the future.

Restrooms are places where water is used a lot on weekdays, so water leaks are likely to occur. So, how to deal with a leak in the bathroom? The following is a brief introduction for you.

1. The door stone at the door of the bathroom.

Water seepage: The water seepage of the stone at the door of the bathroom is likely to be due to the fact that the waterproof layer under the tile at the door of the bathroom is relatively high, higher than the sewer pipe.

If you don't pay attention to such details in the construction process, it is also very devastating to have such problems in the later stage. If you want to solve such a problem completely, you need to make a big move, first pry open the tiles in the leaky area of the bathroom, re-lay the waterproof layer, and pay attention to the appropriate waterproof layer near the door, so that the water flow will naturally introduce to the sewer pipe, only in this way will the leakage situation continue to worsen.

2. Water leakage at the top and corner of the bathroom: we all know that the corner of the bathroom is the junction of the wall and the ground. At this time, you can not warp the floor tiles first.

You can buy some materials for arc plugging treatment, there are many plugging materials, you can learn about it.

3. Water seepage around the toilet down the water pipe: If there is water seepage in the bathroom, it is likely that the water leakage is not done.

At this time, it is necessary to redo the waterproofing layer. Well, after reading so much knowledge about how to deal with water leakage in the bathroom, everyone has a deeper understanding of this problem, and if a similar situation occurs at home, everyone also understands what to do.

Hello, the house has been renovated and lived in for three years, and the bathroom is found to be leaking, you should contact the original decoration company to send the construction team to re-do the waterproofing to ensure that there is no leakage.

In the case of one share, the problem should be handled by the original renovation company. Because there is a warranty period for the quality of the project, this is 5 years.

For details, please refer to: Warranty period for waterproof works.

Article 40 (2) of the Regulations on the Quality Management of Construction Projects stipulates that the leakage prevention of roof waterproofing works, toilets with waterproof requirements, rooms and external walls shall be 5 years.

The house has been renovated for three years, and the bathroom is leaking, so you should go to the company that decorates it. The waterproofing of the bathroom is not done well, and they should be responsible for dealing with it.

I think if your house has been renovated and you have lived in it for three years, once the problem of water leakage in the house appears, the most important thing is to find someone to repair it yourself, rather than pursuing responsibility. It's been three years since I pursued responsibility, and it's hard to catch up. So it's better to find someone you trust to repair it as soon as possible.

I can only find yourself, it's been three years, and the other party won't compensate anymore, you can only fix it yourself. If you find a renovation company within a year, they will admit it, but they will not be able to recognize it again in three years.

You look for the decoration staff to see this, it is good to deal with it directly, and if it is not easy to deal with it, let the original decoration staff come to see, you can pay half of the money to repair, or redo, you want to pay a penny, and it is impossible.

Renovated, so very relieved. After the renovation of the new house, we happily went to move in, and after staying for 2 months, we found the bathroom tiles. It is also possible that the proportion of cement used is not suitable.

Find the bathroom that will decorate the bathroom for you. Waterproofing is not done well. Now there is water seepage and leakage. Let the decorator rebuild the bathroom for you.

It is very likely that it is caused by the fact that the dry and wet separation is not done well during the decoration, or it may be because the sealing of the pipe is relatively poor, so it will lead to water leakage, and it may also be caused by the fact that there is no ventilation for a long time.

It may be that it was not done well when doing the waterproof work, although it was repaired, but the closed water experiment was not successful, and there were some gaps that were still leaking, so it would leak after repairing.

It may be that the waterproofing work is not done well, or the pipe is broken, or it may be caused by a failure during the installation process.

First of all, we must find the leakage point, first of all, see if there are cracks in the roof, there are bubbles indicating that the water has entered the bottom of the waterproof layer, so the water is leaking, and we must also find the cause of the leakage is man-made damage, or the quality of the building itself.

It may be that the waterproofing treatment is not done well, or there is a leakage, or it may be caused by a leaking water pipe.

There are many reasons for water leakage, such as broken pipes or poor waterproof layers, which need to be eliminated.

After three years of moving into a new house, the bathroom suddenly leaks, how to solve it?

Hello, the house has been renovated and lived in for three years, and it is found that the bathroom is leaking, and you should contact the original decoration company to send the construction team to re-do the waterproofing to ensure that there is no leakage. In the case of a share, the problem should be handled by the original renovation company. Because there is a warranty period for the quality of the project, this is 5 years.

For details, please refer to: Article 40 (2) of the Regulations on the Quality Management of Waterproof Projects, which stipulates that the leakage prevention of roof waterproofing works, toilets with waterproof requirements, rooms and external walls shall be 5 years.

Summary. Reasons: 1. The connection between the toilet and the drain pipe is leaking, because the height of the drain pipe is not enough, the depth of the outlet of the toilet into the drain pipe is not enough, and the connection is not filled tightly; The waterproofing treatment in the bathroom is not good, and after the toilet is used, the floor is watery, the walls are damp, and even the lower roof wall is damp and dripping.

2. Water leakage at the inlet of the well on the squatting pit. During construction, the water interface of the squatting pit was smashed and not found. After the rubber bowl is not tied with water, or after being tied with iron wire, the iron wire is rusty and broken, and the connection between the rubber bowl and the water of the squatting pit is broken, so that the squatting pit is waterlogged after use.

The walls are damp, causing the lower roof and walls to be damp and dripping. 3. The installation of sanitary ware is not firm, the reason is that the embedded wooden bricks are not licensed or embedded at the end during construction, the installation of sanitary ware is not firm, and the sanitary ware is loose and unstable when used, causing damage or leakage of pipeline connectors. Method:

Chisel the floor tiles at the floor drain position of the bathroom, and dig grooves around the pipes of the floor drain"Plugging the leak"Stuffed. Brush with waterproof paint. After passing the leakage test, repair the ground.

I chisel a groove around the pipe of the floor drain in the ceiling spot downstairs and use it"Plugging the leak"Stuffed.

Reasons: 1. The connection between the toilet and the drain pipe is leaking, because the height of the drain pipe is not enough, the depth of the outlet of the toilet into the drain pipe is not enough, and the connection is not filled tightly; The waterproof treatment in the bathroom is not good, after the toilet is used, the ridge of the ground is watery, the wall is damp, and even the lower roof wall is damp and dripping. 2. Water leakage at the inlet of the well on the squatting pit.

During construction, the water interface of the squatting pit was smashed and not found. After the rubber bowl is not tied with water, or after being tied with iron wire, the iron wire is rusty and broken, and the rubber bowl and the squatting pit K water connection cherry blossom is not broken, so that the squatting pit is watered on the ground after use. The walls are damp, causing the lower roof and walls to be damp and dripping.

3. The installation of sanitary ware is not firm, the reason is that the embedded wooden bricks are not licensed or embedded at the end during construction, the installation of sanitary ware is not firm, and the sanitary ware is loose and unstable when used, causing damage or leakage of pipeline connectors. Method: Chisel the floor tiles at the location of the floor drain in the bathroom, and dig grooves around the pipes of the floor drain"Plugging the leak"Stuffed.

Brush with waterproof paint. After passing the leakage test, repair the ground. I chisel a groove around the pipe of the floor drain in the ceiling spot downstairs and use it"Plugging the leak"Stuffed.

The bathroom floor drain leaks to the ceiling of the living room downstairs, such a long distance, the floor drain is at the door of the bathroom, and it is usually used for washing machine dehydration and water release.

Dear, then you have to determine whether it is a leak in the bathroom at your home, and another reason is that dry water will penetrate, so it is possible for the acornaceto to flow down the ceiling to the living room when the distance is not particularly far.

The bathroom is the area with the largest water consumption in the whole home, and it is also the most prone to water leakage, so what should I do if the bathroom in the new house leaks? Today I will answer for you, and friends who want to know may wish to take a look with us!

1. What should I do if the bathroom of the new house leaks?

1. If the bathroom leaks during the inspection, the developer should be notified in time and the developer should be asked to deal with and repair.

2. If the bathroom leakage is found in the process of decoration, it may be caused by the construction of the upstairs, at this time, the residents upstairs should be notified, and the other party should be informed of the leakage, and the waterproof treatment should be required.

3. If it is found that the bathroom is leaking after moving in, the cause of the leakage is likely to be because of the leakage of the pipe, at this time you need to find the property of the community to solve, it is best not to check it privately, because the specific location of the pipeline can only be determined in the architectural drawings of the property, so notify the property of the community in time to help investigate, and then repair.

4. If it is obvious that there is a water leak upstairs, you can go directly upstairs to discuss with the neighbor and inform the neighbor of the water leakage.

5. But when you find that the bathroom is leaking, you should first check whether there is any problem with your pipe, and if there is a problem with the open pipe, you can repair it directly.

6. All in all, when a water leak is found, we must find the right person responsible, and the most important thing is to find out the cause of the water leakage and then investigate the responsibility.

Summary: The above is what to do if the bathroom leakage in the new house is shared for everyone, I believe you have a corresponding understanding after reading the above sharing, if you need to know more about it, please continue to pay attention to Qijia.com**, which will answer for you one by one.

Summary. Hello, this depends on the specific leakage, if it is caused by the improper construction process of the decoration company, then the decoration company must be held responsible. If the leakage in the bathroom is caused by the residents themselves, then all the responsibility will be borne by themselves.

Hello, this depends on the specific leakage, if it is caused by the improper construction process of the decoration company, then the decoration company must bear the responsibility. If it is said that the leakage of the bathroom is caused by the residents themselves, then all the responsibility will be borne by themselves.

In addition, there is a situation that the main sewer pipe of the bathroom is ruptured, such as the leakage of the bathroom due to this reason, then the responsibility will be borne by the developer, in order to let the developer come forward to repair as soon as possible, the owner can first contact the property demolition company, and the property company will contact the developer.

Isn't it that the bathroom waterproofing developer wants to guarantee it for 5 years.

Less than two years after the house was closed.

If it's not because the waterproofing is not done well, then you can find a developer.

First of all, look at the floor to see if there are loose and porous tiles. If there are hollow bricks, the water in the gaps should be drained before filling the caulk. Water should be added to the stirrer during processing, and then plugging and squeezing should be added while stirring until there is no powder after stirring evenly.

If the floor tiles are moved or deformed, add the base oil instead of clean water to the mixer and stir evenly. Once the ingredients are stirred, wait 10 minutes and stir again before using. When repairing, you can fill the gap with a professional knife or scraper, and then press the caulk diagonally into the gap without leaving a gap.

Then remove the spilled slurry diagonally, and do not take out the slurry in the gaps. If there is excess mortar on the brick surface, clean the surface with a damp cloth so as not to affect the appearance.

When solving the problem of upward water seepage from the bathroom floor tiles, it is necessary to pay attention to remediation. If there is a leak in the waterproof layer, it is necessary to remove the tiles, and it is best to confirm that the interior wall is the best, and then make a layer of waterproof floor tiles. If it is caused by damage to the water pipe, it is necessary to pressurize the water pipe to confirm whether there is water leakage, determine the specific leakage location, and replace the water pipe.

If the wall leaks due to the humidity of the environment, in daily life, pay more attention to opening windows for ventilation and strengthen cleaning and tidying. If the cracks of the tiles are not treated well and the ground is leaking, you can find a special construction worker to clean up the part filled with cement, and then carry out special waterproofing treatment.

Polished bricks or full-body bricks are recommended for the floor and wall of the living room, because they are wear-resistant and easy to clean. Polished tiles and all-over tiles are recommended for kitchen floors, as the kitchen uses water. In order to prevent water from splashing on the floor and slipping, choose a wear-resistant and non-slip one.

Bathroom floors, like kitchens, need to be wear-resistant and non-slip. The kitchen has a lot of oil smoke and oil stains, so it needs to be scrubbed frequently. Therefore, glazed tiles are selected for wall tiles, which have good oil resistance and wear resistance.

It is recommended to choose glazed tiles for the walls of the bathroom. The brick surface needs to be moisture-proof, the brightness should not be too high, and it can be matte. First of all, it is necessary to know what causes water seepage on the bathroom floor tiles.

There are several reasons for this: the bathroom is not waterproofed in place; Secondly, the water pipes in the wall are damaged, resulting in water leakage; There is also rainy weather, because the air is humid, resulting in water on the surface of the floor tiles; Finally, the cracks of the floor tiles are not good, and there is water seepage.