How to install a car reflector? How to disassemble?

Be sure to determine the appropriate position, be stable when installing, adjust the position of the reflector according to your height and driving habits, unscrew the screws when disassembling, and use professional tools.

It can be installed with a screwdriver according to the manual. When disassembling, you only need to find the position of the screw, and then unscrew the screw, and you can remove the reflector.

When installing car reflectors, be sure to find professional personnel to install them, and car mirrors are very important. After installation, you need to do your own maintenance.

How to disassemble and grind the car interior mirror is very simple, the following is a detailed introduction to the method of disassembly, the specific process is as follows:

1. First of all, hold the support rod behind the car interior mirror with blindness as shown in the figure below.

2. Next, rotate the support rod behind the car interior mirror clockwise as shown in the figure below.

Pinch the cylinder behind the mirror, then rotate it 45 degrees counterclockwise to remove.

When removed, the interior mirror base remains attached to the front windshield. When installing, just align and then rotate 90 degrees clockwise. Pay attention to the strength when disassembling and installing to avoid damaging the front windshield.

Note that removing the inner rearview mirror can easily damage the base, resulting in loosening after installation.

In fact, many people remove the inner rearview mirror because they think it is an eyesore. Here it is recommended that car owners must develop the habit of looking at the rearview mirror in the car, which can save lives at critical moments. For example, when changing lanes, many car owners observe the left and right side rearview mirrors, in fact, observing the inner rearview mirror can judge the distance from the rear car, especially when driving on the highway.

As for how to judge the distance from the rear car through the rearview mirror in the car, you can refer to this method. When you just see the front wheels of the rear car in the rearview mirror, the distance between the front and rear cars is about 13 meters; When you see the middle mesh, it is about 6 meters; See the upper edge of the rear bumper of the front car, about 1 meter.

Why can the interior rearview mirror accurately see the distance from the rear car, because the interior rearview mirror is a plane mirror, and the exterior rearview mirror on both sides is a convex mirror, and the close-range scenery display will become exaggerated, deformed, and the distance will become farther away. The inner rearview mirror of the flat mirror reflects the true distance.

Hello, BYD inner rearview mirror disassembly method: pinch the cylinder behind the rearview mirror, counterclockwise rotation 45 degrees to remove. The functions of the inner rearview mirror are:

1. Observe the rear road conditions; 2. Look at the rearview mirror when braking suddenly; 3. Judge the distance from the rear car; 4. Observe the rear passengers. Take the BYD S6 as an example, it is a mid-size SUV with body dimensions of 4810 mm long, 1855 mm wide, 1680 mm high, 2720 mm wheelbase, and 72 liters of fuel tank.

The BYD S6 is equipped with a turbocharged engine with a maximum power of 113 kW and a maximum power speed of 5,200 rpm.

The steps to remove the car rearview mirror are as follows:

To remove the rearview mirror, you must first deal with the rearview mirror lens, press the head of the lens with your hand to make the tail cocked, and then grab the tail with your hand and pull it out forcefully to remove the lens. After removing the lenses, if the car has a rearview mirror heating power shed, then the wire end of the heating sheet must be unplugged. After unscrewing the screws on the edge and bottom of the mirror, unscrew the screws that hold the mirror in place under the mirror.

Finally, disassemble the bracket connecting the rearview mirror and the body, find the hidden screw between the bracket and the rearview mirror, screw it out with a screwdriver, and then remove the middle part, and the disassembly of the car rearview mirror is completed.

On rainy days, the rearview mirror has a solution where the rain can't see clearly

1. Install rain collapse and wheel block, which is suitable for use when the rain is not very heavy. Installing a rain shield can collapse and the wheels block the water on the windows, keeping the rearview mirror and side glass clear as a whole.

2. Use soap or dish soap, spray soapy water or dish soap water directly on the rearview mirror when using, and dry it. The detergent contains surfactants, in which the hydrophobic group will migrate water outward due to its physical properties, and tissue water droplets will be formed, but the duration of the group signal is short, and it will fail in about two days.

3. Apply water repellent agent to achieve the effect of making the surface of the rearview mirror not stained with water. The main ingredient of the glass repellent is silicone oil, which can achieve the effect of not staining the surface of the rearview mirror by changing the tension of the water on the glass surface.

The installation method of car rearview mirror is as follows:

1. After buying the rearview mirror that suits your model, you need to distinguish the logo on the black plastic card tray on the back of the lens, with the letter L on the left lens and the letter R on the right lens.

3. Connect the metal buckle at one end of the head, and then clamp it with the bayonet above the black plastic card tray on the back of the lens; Put the wired lenses into the rearview mirror housing, gently adjust the position, and press slowly and hard, when you hear the "click" sound, it means that all the lens buckles have been installed.

Tools: 1 flatlot screwdriver, 1 old towel.

First of all, adjust the mirror to the most downward, the most left, and then use a screwdriver to start prying out of the position in the picture below. You can use an old towel pad when prying.

Comparison of the removed lenses and the purchased lenses.

Before installation, first remove the two small iron plates behind the original lens and install them on the new lens, then first clamp the two clips behind the lens sideways to the outer circle of the adjustment plate, and then push the diagonal clip to install it. To emphasize, the clip on the back of the lens is stuck on the outer circle of the adjustment disc, I didn't pay attention to it at first, I didn't install it for a long time, and I broke 2 clips. If you have the conditions, you can use hot water or a hair dryer to heat the clip behind the lens, which should be easier to install.

After the reflector was installed, it cost 30 yuan + half an hour, which is quite a sense of accomplishment.

The car has three rearview mirrors, which are the left, right, and interior mirrors. Adjust the upper and lower halves of the horizontal line first, which is the position of the midline. Then adjust the left and right eyes of the rearview mirror, and adjust the range of the body to a quarter of the mirror.

The old driver's adjustment is that he can see one-third of the contact point between the rear tire and the ground and the rear body from his seat, so that the rear scene can be seen clearly) The interior mirror can see through the rear glass through the rear glass.

Generally, there is a bayonet on the lens, and after alignment, press it in.

The exterior rearview mirror is divided into left and right sides, and can be divided into manual or electric remote control according to the operation method. The exterior mirrors are mounted in two different positions: on the door glass and on the fenders next to the front bonnet. According to the color, it is divided into the same color and different color as the body.

Exterior mirrors are mounted on the door windshield and fenders next to the bonnet.

Now take the electric rearview mirror next to the door windshield as an example to introduce the installation steps:

1) Use a screwdriver to remove the plastic plate fixing screws from the car.

2) Remove the plastic plate to see the fixing screws of the mirror and door, and use a screwdriver to remove the screws.

3) Insert the new mirrors through the window and connect the power cord.

4) Lock the door fixing screws, then move the plastic plate to its original position and lock the screws.

There is a plastic lid on the top of the mirror to open, there is a clip inside, remove the clip inside is a spherical medium, I personally think it is not easy to install, I pretended to take half an hour, not a professional do not disassemble.

The reversing mirror can be adjusted directly by hand, and when adjusting, it is necessary to adjust evenly and forcefully with both hands, and fine-tune it in a small way. Generally, it can be adjusted to the front and back, left and right, and try to avoid frequent adjustment, otherwise it will cause the rearview mirror to shake. Some vehicles have buckles in the indoor mirrors, which need to be opened to adjust the mirrors, and after adjustment, buckle them to fix the mirrors.

Note that before and after the buckle is fastened, the rearview mirror will move, leaving room for adjustment. How to adjust the outdoor rearview mirror. The outdoor reversing mirror of an ordinary car is manually adjusted, or there is a control lever at the inner glass, and the outdoor rear-reversing mirror can be adjusted after being pulled, and the control lever should be slightly adjusted when adjusting.

If you are manually adjusting the outdoor reversing mirror, press and hold one side when pressing the lens, and adjust it gently, not too hard, otherwise the lens will be damaged. Now the mid-to-high-end cars are electrically adjustable outdoor mirrors, so you must not adjust the lenses by hand, after finding the switch on the console, you can slowly use the button to fine-tune.

Automobile reflector disassembly method:

1. How to disassemble the rearview mirror: pinch the cylinder behind the rearview mirror, and then rotate it 45 degrees counterclockwise to remove it. Rotate 90 degrees clockwise when installing. However, it is recommended that LZ do not easily disassemble the rearview mirror, there is a certain probability that the inner glass will be pulled down;

2. You're going to tear down the base together, right? Octavia car interior mirrors are difficult to remove, do your mirrors come with rain sensors? If you don't bring it, turn it 90 degrees to the left and pull it down.

3. If you bring it, it is more troublesome, you need to use a small flat screwdriver to pry open the round seam in the middle. Pull down firmly. If there is a rain sensor, it is recommended to go to 4s.