How to make a girlfriend bracelet? How to make a girlfriend bracelet

Prepare tools Ingredients: thread, scissors, lighter.

Steps. First, prepare 6 threads and tie a knot together.

Steps. 2. Pick up the two lines on both sides, wrap around the middle four lines, and use one of the two as the starting line to tie a neat knot.

Steps. 3. After tightening slightly, tie a knot from the other side for the starting line.

Steps. 4. Tie the knot 5 times in a row in this order.

Steps. 5. After that, the top one of the edges is sloped downward, and then all the threads are knotted around this thread, and each thread is tied twice in a row.

Steps. 6. Turn the line in the opposite direction, at an angle of about 90 degrees. Continue to tie the knot around this line.

Steps. 7. Continue knitting in this order until it fits the length of your wrist.

Steps. 8. When waiting for the end, repeat the third and fourth steps to tie the knot of 5 finishes to tighten.

Steps. 9. After the knot is finished, tie several threads together to make a knot symmetrical.

Steps. 10. Cut a small piece of line, pull up the two ends of the bracelet like the middle, neatly, and continue to tie a few neat knots.

Steps. Ten. 1. Weave to a suitable length, cut both sides short, and leave a small part.

Steps. Ten. Second, burn both sides with a lighter and stick them up immediately.

Steps. Ten. Third, after a little tidying up, a good-looking bracelet is completed.

Tools and materials: embroidery thread, scissors.

1. Select a few strands of embroidery thread.

2. Measure the first strand. The length of the thread is slightly longer than the fingertips to the shoulders and then cut shorter.

3. Trim the remaining thread according to the strand that has been cut. At least 3 strands of thread are required, generally the bracelet made of four to six strands is slimmer, and the bracelet made of eight to ten strands is a little stronger.

4. Pin the bracelet to the pants with a pin during the production process. Tie a square knot at the end of all the lines and fasten them. There are many ways to fasten the bracelet, you can choose the one that is convenient for you, the most common way is to use a pin through the node and attach it to the trouser leg.

6. In order to make the bracelet more attractive, you can weave a few small twist flowers before weaving the pattern.

7. Wrap the leftmost strand around the nearest strand on the right strand and tie the knot.

8. When tying the first strand, tighten the second strand.

9. Repeat the above weaving until the length of the bracelet is moderate.

10. If necessary, you can make a small twist.

11. You can also add some amulets or beads to the end. Use the same technique to weave two bracelets, and the girlfriend bracelet is braided.

The best friend bracelet is made as follows:1. Cut a piece of paper, one section is thin, and one end is thick.

2. At the thick end, we draw a picture with a pencil and open a few seams.

3. The front and back sides are reinforced with adhesive tape (transparent tape).

4. Wrap it around, showing the appearance of a bracelet.

6. This comparison has a three-dimensional sense and is suitable for primary school students' handmade girlfriend bracelets.

The best friend bracelet is made as follows:1. Braided to the appropriate length.

3. The leftmost winding is the axis, and three oblique windings are arranged to the right.

4. Pull down and weave an oblique knot for the shaft.

5. The axis remains unchanged, and continue to weave an oblique knot.

6. Winding to the left to weave two oblique knots.

7. The leftmost line is the axis, and an oblique knot is braided to the left.

8. Fold the axis back and weave an oblique knot.

14. Add ** knotting and sintering.

Handmade girlfriend bracelets, cute and interesting patterns are free to play, simple and good-looking.

Answer 1: Cut a piece of paper, one section is thin, and one end is thick. 2. At the thick end, draw a pencil and make a few seams. 3. The front and back sides are reinforced with adhesive tape (transparent tape).

4. Wrap it around, showing the appearance of a bracelet. 5. Draw the pattern you want on the paper. 6. Then pin it on, it's very three-dimensional, and it's done.

What should I do if I owe too much money and can't pay it back? Lianyungang these methods do you know the debt overdue resolution center advertising lin xiaoxiao.

The best friend bracelet is made as follows:

1. Braided to the appropriate length.

2. Take a 20cm red line as the axis, and the four strands of braid as the winding, and weave a slot.

3. The leftmost winding is the axis, and three oblique windings are arranged to the right.

4. Pull down and weave an oblique knot for the shaft.

5. The axis remains unchanged and continues.

6. Trim the excess part and refine the bracelet, and the boudoir Chi Dami bracelet will be completed.

How to do girlfriend bracelets, you can knit according to the shape of the bracelet that your girlfriend likes, and show his favorite color to the side, you can follow what agreement between you and what you like, you know what he will like, you can click on some of the online knitting methods to find what you like I am giving to girlfriends.

The process of making and erecting the Seven Treasure Knot:

1.Prepare 8 lines, divide them into two groups on the left and right, and use the group on the left to weave a flat knot first.

2.Use the left set of lines to make another flat knot, tighten the two lines, and complete a two-way flat knot on the left.

3.Use the right set of lines to weave 1 upper left two-way flat knot, and tighten the two lines. Then take the 4 threads in the middle as a group and weave 1 flat knot.

4.Then make a flat knot again, tighten the two lines, complete a two-way flat knot on the left, and use a group of lines on the left to make another two-way flat knot on the left.

5.Use a set of lines on the right to make another two-way knot on the left, and then repeat the above steps to form a Qibao knot.

Girlfriend bracelets can be arranged as follows:Tools Ingredients: two square origami sheets.

Method Steps:

1. Prepare two squares of origami in two colors.

2. Folds them diagonally on top of each other.

3. Then open it and fold one of the corners 3 times towards the middle branch of the hail line.

4. Open it and fold it into a wavy shape along the crease.

5. The other half is also folded and folded in the same way.

6. Finally, insert and fix both ends, and a simple girlfriend bracelet is ready.

There are many ways to weave girlfriend bracelets, and the following is one of the easiest to learn methods: Materials: - Colorful strings - Scissors steps:

1.Choose two colored strings and cut two each, about twice the length of your wrist. 2.

Fold two strings in half, tie a knot at the fold, and attach the knot to a table or other fixture. 3.Place the left string on the right string, then pass the left string under the right string, and then through the right string from the left string and pull the string tight.

4.Repeat the third step until the weave is to the right length. 5.

After weaving to the right length, knot the two strings of Shanxun together, and then cut off the excess strings. Such a simple girlfriend bracelet is complete. You can choose different colors and knitting methods according to your preferences to make the bracelet more unique.