Why is the Little Swan fully automatic washing machine so loud when it is dehydrated?

Updated on home 2024-08-15
10 answers
  1. Anonymous users2024-02-16

    Washing machine noisy reasons:

    The washing machine is not installed evenly, so be sure to choose a flat ground and adjust the horizontal position.

    The motor bearing or transmission shaft bearing is seriously worn or broken, and the gears of the gearbox of the automatic washing machine are faulty.

    How to reduce the vibration and noise of the washing machine? After the washing machine is used for a long time, due to mechanical wear, lack of lubricating oil, aging of parts, fatigue and deformation of tension springs.

  2. Anonymous users2024-02-15

    It may be caused by an unbalanced collision barrel, or it may be a broken clutch.

  3. Anonymous users2024-02-14

    The main reasons for this are: unbalanced placement of clothes will lead to uneven force on the washing machine, resulting in the noise of the inner bucket hitting the side of the washing machine; If the motor bearing is damaged, the bucket will hit the inner wall when washing clothes; Using the washing machine for a long time will cause the screws to loosen and make noise; Problems with the starter capacitor can cause noise when washing clothes. Cygnet.

    The solution to the noise of the automatic washing machine when it is dehydrated: 1. The sound of the clothes button or other foreign objects rubbing against the inner wall of the washing machine. Please inspect and clean the contents of the bucket.

    2. The installation of the washing machine is uneven, and the automatic washing machine is more important. 3. Motor bearings or transmission shafts.

    With the bearing is severely worn or chipped, the gears of the gearbox of the automatic washing machine are faulty. If the damage is severe, the firmware needs to be replaced. 4. The pulley rubs against the belt, and the deformation of the pulley rubs against the bottom of the laundry bucket.

    5. The dehydration bucket touches the outer box and needs to be adjusted. 6. A sealing ring on the transmission shaft.

    It's too tight and needs to be adjusted. 7. The fasteners in a certain part are loose and need to be reinforced. 8. The balance boom of the automatic bucket washing machine is out of balance, and the spring should be replaced or adjusted. 9. The motor bearing is seriously worn or lubricated poorly. It is recommended to add lubricating oil.

  4. Anonymous users2024-02-13

    There are many reasons, which can be troubled and eliminated according to the following methods:

    1. Check whether the washing machine is placed smoothly, regardless of whether the ground is flat or not, the washing machine must be perpendicular to the horizontal plane.

    2. Check whether the clothes in the bucket are placed unevenly, resulting in dehydration shaking and noise, at this time, the cover plate should be opened, and the clothes should be evenly placed on the barrel wall around the bucket.

    3. Check whether the four booms on the bucket are consistent, and they should be adjusted consistently. Whether the spring elasticity is the same, if the elastic force is not the same, the new spring should be replaced with the same elastic force. Some washing machines in order to prevent the bucket from swinging too much when dehydrating, the upper part of the bucket is provided with a fixed protective belt, and there is a tension spring on the protective belt.

    4. The balance ring at the top of the dehydration bucket is ruptured or leaking, which makes the dehydration bucket lose its balance when it rotates. Just replace the balance ring and it will solve the problem.

    5. Check whether there is a foreign body between the inner barrel, the wave wheel and the outer barrel in the same way as the noise of washing, and if there is a foreign body.

    6. a flange of the dewatering bucket.

    Loose or cracked fastening screws. Just tighten or replace the flange.

    7. The dehydrated bearing is seriously worn or loose. Simply tighten or replace the dewatered bearings.

    If it is a front-loading washing machine, it can be overhauled as follows:

    Reason analysis: 1. The washing machine is not placed on a hard, flat, clean ground without water and grease.

    2. The shipping bolt was not removed.

    3. The bottom foot of the washing machine is not level and loose.

    4. The washing machine touches other items.

    5. The clothes in the inner cylinder are placed too little or too much, and they are uneven.

    Solution: 1. Please place the washing machine on a hard, flat, clean ground without water and grease. If the washing machine is installed on uneven or unclean ground, noise or vibration will occur.

    2. Remove the shipping bolts on the back of the washing machine.

    3. Press and hold the diagonal of the washing machine with your hand.

    on the two corners, check whether the fuselage has a slight shaking, and adjust the foot balance.

  5. Anonymous users2024-02-12

    It could be because something is stuck, or it could be that this washing machine is such a type.

  6. Anonymous users2024-02-11

    Summary. 1.The belt between the motor and the bucket pomelo is loose. If it's a new machine, it's generally like this, or the plastic protective sleeve behind the motor is not removed.

    2.Running the washing machine to listen to the sound of the motor (motor) can not rotate, if it does not turn (the capacitor burns out. The circuit board does not supply power or the motor burns out).

    3.If the motor is turning, the belt is not coming off, and the barrel is still not turning, it may be that the barrel edge is stuck on clothing or sundries, or the clutch tripod has a foreign object stuck.

    The Little Swan washing machine is dehydrated normally, and the washing sound is normal, but it doesn't turn for any reason.

    1.The belt between the motor and the barrel pomelo is loose. If it's a new machine, it's generally like this, or the plastic protective sleeve behind the motor is not removed.

    2.Running the washing machine to listen to the sound of the motor (motor) can not rotate, if it does not turn (the capacitor burns out. The circuit board does not supply power or the motor burns out).

    3.If the motor rotates, the belt does not seem to fall off, and the barrel still does not rotate, it may be that the barrel edge is stuck on clothes or sundries, or the clutch tripod has a foreign object stuck.

    1.When washing the machine, if the motor is humming, but not turning, it may be a problem with starting the capacitor. If there is no sound from the motor, the linkage switch of the dewatering bucket lid may malfunction; 2.

    Check that the belt is not loose and slippery. If the belt is loose, the speed of the wave wheel will slow down, or even seriously not rotate. Loosen the set screws of the motor, move the motor outward, and tighten the belt.

    However, the belt should not be adjusted too tightly, which will increase the friction between the belt and the pulley, so that the motor will bear too much load, affecting its performance and service life; 3.Check the pawls and clutch to see if the brakes are tightened or if the mechanism plates on the drum cover are broken; 4.The fully automatic washing machine does not rotate, and some motors with clutches are very hot, and the starting capacitor may be broken, or the wire end is off, causing the motor to fail to start.

    If there is no clutch, see if the motor is stuck, do not take the idling motor experiment, whether it is stuck, if not, most of the starting capacitors have problems; 5.Check the gap between the wave wheel groove and the wave at the bottom of the washing machine barrel for any debris or clothing embedded and stuck in the wave wheel. If the motor is still running at this time, the temperature rise of the motor rises sharply due to excessive force, and if it is not detected in time, the motor may be burned.

    As soon as this happens, the power supply must be disconnected immediately.

  7. Anonymous users2024-02-10

    1. The sound of metal impact.

    Solution: Check whether there are metal buttons or other metal objects touching the inner wall of the laundry bucket on the outside of the laundry clothes, and if so, turn it inside and wash it again.

    2. Click-click.

    This sound may be caused by a small object such as a coin falling under the washing wheel, so you need to remove the washing wheel and check it.

    3. The buzz is loud.

    This kind of noise is very large, it may be because the gap between the motor bearing and the shaft sleeve is too large or the bearing is seriously worn, or it may be caused by the loose fixing nut of the transmission pulley and the swing of the pulley, of course, it may also be caused by the improper placement of the pulley, it is recommended to check it carefully.

    4. When the clothes are dehydrated, it makes a lot of noise, and the body of the washing machine will beat, which may be caused by uneven placement of clothes, or it may be the leakage of the dehydration balance ring of the inner barrel.

    5. There is also a possibility that the clutch spring is broken and the washing machine makes a sound, so you can change the clutch spring.

  8. Anonymous users2024-02-09

    The quality is not up to standard. How about the little swan, I can't say clearly, but my company buys the washing machine of Jiangsu Weishide does not have this situation, if you are interested, you can search for Jiangsu Weishide products on the Internet, industrial washing machines, dehydrators, washing machines, dryers, ironing machines are readily available. Wisdom is also a well-known manufacturer of industrial washing machines in China, factory direct sales, preferential sales.

  9. Anonymous users2024-02-08

    The quality is unqualified, and the inner cylinder must not hit the outer cylinder.

  10. Anonymous users2024-02-07

    Normal, physical principles, inertia.

Related questions
9 answers2024-08-15

When encountering a failure of the washing machine with poor drainage or no drainage, do not rush to judge whether the washing machine is faulty. You should first check whether the drain pipe of the washing machine is lowered and whether the water outlet is too high, and the water outlet should be lower than that of the washing machine, so that the water can be drained normally, otherwise there may be water accumulation. If all of the above conditions are normal, then check the cause of the failure of the washing machine's drainage system. >>>More

11 answers2024-08-15

1.in the control panel of a fully automatic washing machine. >>>More

10 answers2024-08-15

The possible reasons why a fully automatic washing machine can wash and cannot be dehydrated (cannot enter the dehydration program) are as follows: >>>More

10 answers2024-08-15

In case the unbalanced clothing causes the bucket to be broken, it is usually under the water inlet valve.

9 answers2024-08-15

The little swan washing machine washes clothes normally, sometimes dehydration is normal, and sometimes it keeps buzzing when dehydration, the speed is slow, the dehydration does not dry, open the door, turn the inner cylinder in reverse with your hands, and sometimes it can be dehydrated normally?