How to remove the Emmet electric fan for cleaning

Emmet electric fan dismantling and washing: Remove the Emmet electric fan first and then clean the fan.

1. First of all, loosen the chuck of the electric fan protection net by hand.

2. After loosening, you can take out the front mesh cover of the electric fan by breaking it up with your hand.

3. Then directly unscrew out the motor shaft nut by hand.

4. After taking off the plastic nut, you can take out the fan blade, and ask to take out the fan blade manually.

5. Loosen the rear mesh nut and manually screw it out.

6. Take out the back net and manually take out the back net.

Electric fan cleaning method:

1. Preparation: Before all the work begins, cut off the power supply, if you have just used the electric fan before cleaning, then it is best to let it cool down to prevent hot hands;

2. Disassembly: first disassemble the protective net, the protective net is generally fixed by buckles or screws, the fan fixed by the buckle only needs to open the buckle, and the fan fixed by the screws needs to use a screwdriver to unscrew the screws, and then take off the protective net and put it in the cleaning basin (note: the removed buckles and screws and other small parts are best placed in a small box to avoid loss); Then disassemble the fan blade, generally rotate the fan blade along the clockwise direction to remove, and put the fan blade into the cleaning basin;

3. Cleaning: Add water and detergent to the cleaning basin, carefully scrub the protective net and fan blades, the detergent can choose laundry detergent or detergent and other commonly used household products, but do not use oil-based detergents such as gasoline, because oil-based detergents will cause corrosion to paint and plastics, damage the appearance and even life of the electric fan; Then scrub the small parts and body with a rag dipped in detergent; After washing, dry all parts with a clean, dry cloth and let it dry in a ventilated place for a while.

4. Installation: Finally, install all the components back in reverse order when dismantling, and the cleaning of the electric fan will be completed.

How to disassemble the Emmet electric fan.

1. If you want to disassemble the electric fan, you must first disconnect the power supply to avoid electric shock.

2. Emmet fans are mainly Phillips screws and hexagonal plum screws, so you can prepare the screw tool assembly.

3. Unscrew the screws of the outer grille cover of the fan, which will generally be stuck by the buckle, so do not break it hard. Press down on the clasp of the grille, and then tap both sides of the grille firmly with both hands.

4. Then remove the fan blades, in general, the ** fan only needs to disassemble and clean the fan blade grille. The vertical fan also needs to disassemble the fan foot plate, loosen the big screw at the bottom of the foot plate, and then remove the tube on the foot plate to complete the disassembly.

Emmet Fan Cleaning Method.

1. Prepare a rag that does not shed hair.

2. Prepare dish soap (other effective detergents are also available).

3. Soak the rag with water and pour an appropriate amount of dish soap.

4. The rag should be wrung out of the water, but not too dry, to ensure that it will not drip.

5. Wipe the whole electric fan normally, focusing on wiping the fan and fan cover. When removing the fan cover, you need to remove the fixed clamp first, and the fixing method of the clip is different depending on the situation.

6. Wipe the fan blades and fan blade cover, except for the first one or two use of dish soap, then wash the rag and wipe it directly until there is no dish soap residue on the surface of the fan. (Remember that the towel should not be too wet, in order to prevent damage to the internal accessories of the fan) 7. After wiping, the fan will look new, and it needs to be dried for a few minutes and then turned on the power and blowing, and the fan will be clean and dry.

7. It is also very simple for cleaning fan blades. Laundry detergent can be used for cleaning, but do not use oil-based stain removers such as gasoline, as oil-based stain removers can cause corrosion to paint and plastics, damaging the appearance and even life of electric fans. After cleaning, wipe all parts with a clean, dry rag and place them in a ventilated place to dry.

The easiest way to do this is:

1. Remove the screws on the mesh ring with a screwdriver (the cover has a hula hoop and a screw at the bottom);

2. Put the fan on the left side and put it down, so that the mesh ring is against the ground and then slap it on the highest part of the mesh circle;

The plastic nut can't be taken out, so it's done.

The method of disassembling the Emmet electric fan is as follows:1. First of all, break the chuck of the protective mesh in the clockwise direction, as shown in the following figure:

2. Remove the front mesh cover of the electric fan after loosening, as shown in the figure below

3. Then unscrew out the shaft nut, as shown in the figure below

4. Then take out the fan blade, as shown in the figure below

5. After loosening, the net nut is manually screwed out, as shown in the following figure

6. Finally, take out the back net, as shown in the figure below

The easiest way to do this is:

1. Remove the screws on the mesh ring with a screwdriver (the cover has a hula hoop and a screw at the bottom);

2. Put the fan on the left side and put it down, so that the mesh ring is against the ground and then slap it on the highest part of the mesh circle;

Cleaning method: Clean with a soft cloth or sponge, if there is oil, add an appropriate amount of dish soap, and apply the dish soap first · Soak the fan blades for a few minutes, so that it is easier to clean, try not to use rough materials to clean, otherwise it is easy to damage the leaves. After cleaning, place the fan blades in a cool place to dry, away from direct sunlight, as it will speed up the aging of the fan blades.

Suggestion: It is best not to clean the electric fan frequently, so that frequent disassembly will not only increase the probability of damage to the installation site, but also accelerate the aging of the fan blades, so as long as the fan blades are not too dirty, try not to clean, use a wet towel after the power is off, drop the fan frame, and wipe it.

Emmett designer was playful when he was a child, and the people in the martial arts ** slapped him both sides of his hands