What s the matter with the gas stove going off as soon as you let go

What is the reason why the gas stove goes out as soon as it lets go.

It may be that the time of holding down is not enough, and the current electronic lighter gas stove is equipped with flame-out protection equipment, which means that the ignition needs to be pressed for 5 to 10 seconds before the induction needle will work.

If the battery of the gas stove dies, it will also turn off as soon as you let go. The battery of the gas stove needs to be removed and replaced with a new one.

Look carefully at the top of the stove to see if there is a blockage, if it is blocked, it needs to be cleaned up in time, and a thin wire can generally be used to dredge.

Look at the center of the gas stove to see if it covers the pin when it burns, and if it doesn't, it will turn off as soon as you let go. It needs to be repaired in time so that the ignition source can cover the protective pin.

The reason why the gas stove goes out as soon as you let go:

1.Lack of gas.

In the busy environment, many times people will ignore a lot of details of life after work, so many times they will forget to pay the gas bill, when the gas is insufficient, the gas stove will naturally go out as soon as it is fired.

Solution: Pay the gas bill and let the gas be normal**.

2.The battery is low or damaged.

Many gas stoves use the power provided by the battery to complete the ignition function, so when the spark is relatively weak when ignition, it is likely that the battery is low or has been damaged.

Solution: Replace the battery with a new one or wipe the rust off the positive and negative electrodes of the battery.

If you don't know which one to buy, it is best to remove the original battery or consult the after-sales customer service of the gas stove manufacturer.

3.Improper method of operation.

Many gas stoves are different from old gas stoves, which are generally equipped with flame-out protection devices, and you need to press the switch for four or five seconds to successfully ignite the fire.

Solution: Press the switch for four or five seconds when ignition, and wait for the flame to stabilize before letting go.

4.The fire separator was not neatly placed.

On the gas stove, there will generally be a large and small fire cover, that is, what people call the fire divider, the fire distributor must be aligned with each other in order to be used normally, otherwise it is easy to let go of the flame, if it is aligned, but the hole of the flame divider is blocked.

Solution: Clean the hole of the flame splitter and align it with the buckle.

The reason why the gas stove goes out when you let go:

1. What is the reason why the gas stove is extinguished when it is on fire? Buried dampers can be caused by over-adjusting the dampers, which need to be adjusted smaller to reduce the amount of air entering. It may also be caused by letting go too quickly after ignition or the flame does not burn to the flame to extinguish the protective needle, so you need to stay for 5-10 seconds after ignition or wait for the flame to burn to the protective needle before letting go.

2. The gas stove may be extinguished when the fire is set on fire, which may be caused by the excessive adjustment of the damper, which will easily lead to the flame, and the situation that the fire will be extinguished when the fire is released. At this time, you only need to make the damper a little smaller and the orange brightness to reduce the amount of air entering can effectively solve the problem of leaving the flame and extinguishing the flame.

3. When using an electronic ignition gas stove, the ignition will also go out if you let go too quickly after ignition. Because the electronic gas stove is different from the old-fashioned gas stove, it is generally equipped with a flame-out protection device, if you want to avoid the situation of turning off the fire after the ignition, you need to press and hold for 4-10 seconds after the ignition, until the induction needle takes effect before you can let go.

4. There is usually a motor to detect the flame on the gas stove, when using the gas stove to ignite, it is necessary to observe whether the fire cover can completely cover the flame on the protective needle when burning, if the flame does not burn to the flame-out protection needle, there will definitely be a situation where the fire is wide and extinguished.

What happens when a gas stove goes off as soon as you let go?

1. The reason is that the gas stove is blocked, and the gas stove will be connected to a gas pipe, if the gas pipe is bent or flattened, it will affect the transmission of gas, and it will also affect the flame of the gas stove. If it's bent, straighten it, and if it's flattened, replace it with a new one. 2. If the gas stove is used for too long, dust and oil will fall into the stove, and the flames will become red, and the pot will be burned black.

At this time, you can use an old toothbrush to brush the burner, or use a thin wire to connect the burner. Or prepare a toothpick to clean the air hole.

Expand knowledge: 1. It may also be a problem with the fire cover of the gas stove, or the small hole of the fire cover may be blocked, which will also cause the gas stove to not catch fire. To find out that is the problem of the fire splitting cover, what you need to do is:

Remove the fire splitting cover, and then poke the small holes with a relatively sharp object (needles, toothpicks are fine), and then try to light the fire, and clean these small holes more often when you use them.

2. Don't wait until a thick layer of grease accumulates on the stove before cleaning it. It is necessary to develop good cooking habits, and once there is soup and rice spilled on the countertop, it should be cleaned up in time, as it will cause difficulties in cleaning after solidification. Gas stove countertops generally have stainless steel countertops, glass countertops, and enamel panels.

3. Usually you can wipe it with a cloth dipped in detergent, but be careful not to wipe the glass table with a steel wool ball, it is easy to scratch scratches, so that the glass protective layer is damaged, and the table top is easy to burst. In particular, it is necessary to check and clean the gas stove hose frequently, and replace it in time if it is found that there are signs of aging, cracking, scorching, and rat bites, so as to prevent gas leakage, deflating and other safety accidents caused by fire, gas poisoning, etc.