What is the reason why the gas stove is on fire and let go of it?

Updated on society 2024-08-14
15 answers
  1. Anonymous users2024-02-16

    Causes and solutions for extinguishing gas stove fires:

    1.The battery is dead or in poor contact.

    You can buckle the battery and reinstall it again, make sure that all the contact surfaces of the battery are clean, and then check the situation. If it is still off, you can replace the battery and try again.

    2.Thermal probe issues.

    Look at the bad stove on the other side. Will the flame in the middle burn the probe? You have to burn the detector to extinguish the fire. When there is still a point, you can press and hold it for ten seconds. When the switch is released, the probe is thermally sensitive. You have to burn it to put out the fire.

    3. The thermocouple temperature is not enough.

    **Do not release the solenoid valve through the small mechanism on the switch. When the thermocouple reaches a certain temperature, release it. It usually takes more than 30 seconds to a minute.

  2. Anonymous users2024-02-15

    Causes and solutions for gas stoves to be extinguished when they are on fire:

    1. The battery is out of power or has poor contact.

    You can buckle the battery and reinstall it again to ensure that the contact surfaces of the battery are clean, and then light the fire again to see the situation. If the engine is still off, you can replace the battery and try again.

    2. Thermal probe problem.

    Look at the stove on the bad side, whether the flame in the middle can burn the probe, and the probe must be burned to fix the fire. When there is still a point, you can press and hold it for ten seconds, and when you loosen the switch, the probe is the heat induction, and it needs to be burned to fix the fire.

    3. The temperature of the electric couple is not enough.

    After the fire is on, don't let go of the valve of the magnetic valve through the small mechanism on the switch, and let go when the electric couple reaches a certain temperature, generally more than 30 seconds to a minute.

    Gas stove daily maintenance cleaning method:

    1.Stove tile antifouling method.

    Use discarded candle heads, use the most ordinary white candles as a "brush", and gently apply the seams of each tile, first along the direction of the seams, and then cross over after the coating, making sure that the thickness of the candle is equal to the thickness of the tiles.

    This "anti-staining" work can be done in spring, summer and autumn, and it may be a little difficult to apply the candle when it is harder in winter. Because the surface of the candle is smooth, even if there is oil stains on it, just ordinary dish soap.

    You can wipe it lightly with water, and you no longer need to use a small shovel blade and other utensils to shovel away the oil.

    2.Deeply cleanse the cooktop.

    Mix two spoonfuls of white vinegar with 200ml of warm water, then wash the stainless steel cooktop with a sponge and a loofah dipped in this "hot vinegar water" to make it shine as good as new. You can also use 500 ml of hot water with 30 grams of baking soda (sodium bicarbonate.

    Mixing, you can also use a loofah to dip it in, and easily remove the grease on the stove.

  3. Anonymous users2024-02-14

    Caused by a dead battery, a damaged microswitch, or an offset ignition pin.

    Check whether the battery is a little bit, and observe whether the spark is weak or weak when ignition, indicating that the battery is about to run out of power or the line is not in good contact. At this time, it is necessary to replace the battery, find the position of the positive and negative poles of the battery, and accurately place them to ensure that the circuit is closed.

    Check the position of the ignition needle, with the use of time for a long time, the ignition needle position of the gas stove may be offset, under normal circumstances, the distance between the ignition needle and the fire cover is four to six centimeters, if the deviation distance is too much, it will cause the gas stove to not catch fire, you need to adjust the alignment of the fire hole.

    Check whether the micro switch is damaged, the gas stove has been used for a long time due to frequent switches, the inside of the switch will be worn or broken, or there will be poor contact of the switch, then you need to ask a professional maintenance master to check and repair.

  4. Anonymous users2024-02-13

    1. The current electronic ignition gas stove is different from the old gas stove before, and the current stove is equipped with a flame-out protection device, and it is necessary to press 5-10 seconds to wait for the induction needle to work before you can let go;

    2. Determine whether the cooker battery should be replaced, sometimes it is due to the flameout caused by insufficient battery power, and the general cooker battery should be replaced in half a year;

    3. Pick up the fire cover above the stove to observe whether there is any blockage, and if there is, it needs to be cleaned up;

    4. The problem of the solenoid valve body of the gas stove may be damaged by the rotary button and the ignition device.

    5. The internal feedback circuit of the gas stove is faulty.

  5. Anonymous users2024-02-12

    A common cause of failure when a gas stove is ignited and turned off.

  6. Anonymous users2024-02-11

    After the gas stove is on fire, what happens when you let go and extinguish it? Most of the time it's a problem with this sensor needle.

  7. Anonymous users2024-02-10

    The main reason why you can't catch fire:

    1. The "thermometer" is oxidized.

    2. The "thermometer" is dirty.

    3. The "temperature needle" is far away from the "central fire cover".

    4. Short ignition time.

    All these lead to a decrease in the temperature sensitivity of the "temperature needle", slow temperature rise, resulting in false flameout protection.

    The solutions are:

    1. Scrape off the oxide layer of the "temperature needle".

    2. Wipe and clean the "temperature needle".

    3. Aim the "temperature needle" at the fire hole in the direction of the "center fire cover".

    4. The ignition time is longer, that is, do not release the switch immediately after ignition, and wait for the "temperature needle" to heat up before letting go.

  8. Anonymous users2024-02-09

    The reason why the gas stove is extinguished when it is on fire is that the thermocouple and the solenoid valve do not form a circuit circuit.

    The current electronic ignition gas stove is different from the old gas stove in the past, and the current stove is equipped with a flame-out protection device, and it is necessary to press for 5-10 seconds when igniting and wait for the induction needle to work before you can let go.

    Solution: Adjust the height of the thermocouple so that the flame can burn it, and let it generate voltage due to the temperature difference to open the solenoid valve and let the air flow through the fire hole. If you can't open the solenoid valve, it is recommended to open the stove with a Phillips screwdriver to see if the connecting wires inside are connected.

    If you can't get it, it is recommended to call after-sales personnel to repair it.

  9. Anonymous users2024-02-08

    A common cause of failure when a gas stove is ignited and turned off.

  10. Anonymous users2024-02-07

    After the gas stove is on fire, what happens when you let go and extinguish it? The master tells you a few reasons, which is very practical.

  11. Anonymous users2024-02-06

    Now gas stoves have the function of preventing children from opening by mistake, so you have to continue to press the knob for five seconds before you can let go, and you can't ignite the fire for one second less.

  12. Anonymous users2024-02-05

    After the fire, it was still on fire, and then it was extinguished, for what reason.

  13. Anonymous users2024-02-04

    The reason why the gas stove is on fire and goes outThe gas stove may be extinguished when the fire is on fire, which may be caused by the excessive adjustment of the damper, which is easy to lead to the flame when the damper is adjusted too large, and there will be a situation where the fire is extinguished.

    When using an electric gas stove, the ignition will turn off if you let go too quickly after ignition. Because the electronic gas stove is different from the old-fashioned gas stove, it is generally equipped with flame-out protection device, if you want to avoid the situation of extinguishing the fire after the ignition, you need to press and hold for 4 10 seconds after the ignition, until the induction needle takes effect before you can let go.

    When using a gas stove to ignite, it is necessary to observe whether the fire cover can completely cover the flame on the protective needle when burning, if the flame is not burned to the flame-out protection needle, it will definitely be extinguished when you let go.

  14. Anonymous users2024-02-03

    1. This problem may be due to the flame-out protection device, when ignition, you need to press 5 10 seconds with the induction needle, and you can let go after it works.

    2. There is also a situation that the battery power is not enough, resulting in the voltage can be normal**.

    3. If the gas meter is in arrears, it will also lead to this problem.

    4. If the gas pipeline is blocked, it is easy to cause the problem of extinguishing the gas stove when it is on fire.

    5. The ignition needle or induction needle is malfunctioning.

    Method - 1, first confirm whether the use of the method is correct, if the method is incorrect, then you need to use the correct method to ignite.

    2. In addition, check whether the flame-out protection device is faulty, and if it fails, it needs to be replaced with a new one.

    3. Check whether the battery is out of power, remove the old battery, and then replace it with a new battery to use it normally.

    4. In addition, you need to check whether the gas is in arrears, if this is the case, you need to pay the fee, and you can use it normally if you have enough gas.

    5. To determine whether the gas pipeline is blocked, it is necessary to dredge it with professional maintenance personnel of the Zheng Department.

    6. If the ignition needle is faulty, it needs to be replaced.

  15. Anonymous users2024-02-02

    1. In this case, first of all, it is necessary to judge whether the gas stove has a flame-out protection device, if there is, then it is necessary to hold it for 6 8 seconds when ignition, and then let go after the induction needle works, it can be solved.

    2. If the flame-out protection device has been damaged, it needs to be replaced.

    3. Check whether there is a problem with the solenoid valve body, and if there is a problem, you need to replace it with a new one.

    4. In addition, you can also try to adjust the damper under the gas stove to a suitable position, which can solve the problem of extinguishing the gas stove when it is on fire.

Related questions
18 answers2024-08-14

This is mainly because there are some poor contacts at the interface, so don't rush to fire at this time, and be sure to choose a professional to deal with it, because if you don't handle it carefully, it will cause a huge disaster. Because some of the current gas stoves are directly connected to natural gas, once there is a flame situation, it will make the natural gas seriously occur. This can also have a very big impact and disaster for your family and surrounding neighbors. >>>More

23 answers2024-08-14

1.Power issues.

The reason why many water heaters can't be turned on is that the power supply is not in good contact, only check whether the plug of the power supply is on, and if not, unplug the plug and plug it in again. >>>More

8 answers2024-08-14

There are three main reasons for this:

1.If there is wind around the gas stove to blow the flame obliquely, the thermocouple cannot feel the temperature, and the gas stove should not be used in an environment with strong winds; >>>More

15 answers2024-08-14

This is the most common problem, but also people are generally more concerned about the problem, found that the ignition is not on fire and there is no sound of clicking, it is necessary to check whether the battery is charged. The integrated stove has an electronic induction firewall, which can automatically cut off the gas source in the case of high temperature and open flame, and automatically cut off the gas source when the fire goes out accidentally, and automatically cut off the power supply in case of leakage, which is very safe to use. The lower exhaust design eliminates the noise source placed on the human head, and applies ultra-low, noise technology and silent air duct design technology to reduce noise. >>>More

14 answers2024-08-14

The reasons why the natural gas stove does not catch fire are as follows:1. When the gas stove battery is out of power and cannot catch fire, you can check whether the battery has electricity, if there is no electricity, not only can it not ignite but also the solenoid valve will not open. >>>More