Which page is the router adjustment on, and how to set the router page

The settings of various brands of routers are much the same.

1.The router is a device that sets up a LAN to achieve network sharing, and the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, and each computer is connected to the LAN port of the router (if it is a laptop, you should also use the network cable to connect one to the router and then complete the parameter setting), the IP address of the computer network card is set to be automatically obtained, and the address bar of the computer browser is entered yes, and the network parameters obtained by your computer network card should be viewed. Log in through the IP address of the gateway) to log in to the router, the general username and password are admin, set according to the setup wizard, generally choose the PPPOE method, enter your broadband and password;

2.If there is a wireless network name or SSID setting in the setup wizard, complete the setting according to the settings wizard prompts, if not, click to enter the router's WLAN settings or wireless settings, there is a wireless network name or SSID, there is a default can also be automatically set, and then enter the wireless security settings, there is a wireless encryption method selection and password setting, set your wireless signal encryption key;

3.If the laptop uses wireless Internet access, the operation is as follows: right-click the online neighbor - properties - right-click the wireless network connection - view the available wireless network, click your wireless network name in the searched wireless network - connection, and enter your wireless network key for verification, after passing the verification, you can connect to the wireless router to surf the Internet normally; If it is a wireless terminal such as a mobile phone or tablet, the same principle is the same as above, and it can be used after searching for a wireless signal and entering the wireless network key to connect.

Ethernet cable to connect the router to the computer, 192, 168, 1, 1

If you are a general small router, you can use a PC to connect with a network cable, and on the PC, start -> run -> enter cmd. Then a black box pops up,. Enter ipconfig inside,Enter the IP address of the default gateway into the IE address bar,If you are a win7 system,Start menu comes with a running window,Enter cmd directly there and do the following。

Of course, if your router is Cisco, Huawei is such a high-end router. First en enters global mode, then enters conf t to enter port mode. Then enter int fx x (x x is your routing port number), then enter the ip add address (subnet mask) to set the fixed IP, then enter the no shutdown boot port, and then connect your computer to the router.

That's it.

How to get to the settings page of your wireless router. Our wireless routing. I just bought it, how do I get to his settings page? Here's how to set up the router page I've organized, I hope it will help you!

Method.

1. Look at the bottom or the manual

This method is suitable for the wireless router you just bought, or if the router is not set up. Here's how.

We can take a look at the bottom of the router we bought. The IP address and password will be displayed on it.

Then we enter the IP address that we see into the address bar of the browser, then enter the password, and we can enter the settings.

If someone else has already set up the router, how do we get to the page where she sets it up?

Method.

2. Search by IP address

Conditions:1We are already connected to this wireless network.

2.We know the password for wireless routers.

Right-click the network icon in the lower-right corner of the notebook and select Open Network and Sharing Center

Entering the Network and Sharing Center, we select "Change adapter settings".

Find our Wi-Fi and then we double-click on our Wi-Fi icon.

Open "WLAN Status" and then we select "Details".

In the "Details" we can see "IPv4"and IPv4 Default Gateway. Generally, the "IPv4 default gateway" is the IP address of our router settings page.

Then we enter the "IPv4 Default Gateway" address directly into the browser.

It will pop up a router settings interface and let us enter the password to set the router administrator.

We enter the password and then we can enter the settings page of the router.

Isn't it simple. Because some people deliberately change the ** of their router settings page, I hope not to let others set it, but we can see that the IP address he set has broken through the permissions he set.

When people want to adjust the Wi-Fi signal, how do they enter the wireless router settings interface? How to set up the router interface? Let's popularize the common sense of quickly entering the router settings interface.

Utilize the default IP address

At present, for newly purchased mainstream wireless routers, most models have supported the "Automatic Setup Wizard" function. Users only need to connect the power supply of the router, start the router, and then connect a LAN port to the network port of the computer with a network cable.

After that, enter the default IP address of the router on the IE browser (usually found on the bottom nameplate or manual of the router), and you can set up the wireless router.

Take the D-Link DIR-890L as an example, you can see that the default IP address of the router is "see the white box in the figure below" on the bottom nameplate, then the user only needs to type " in the IE address bar, and the login page of the wireless router will pop up.

The default IP address, username, and password of the router are listed in the white box.

Again, type the default username and password on the bottom nameplate or instruction manual into the login page, and click "Login" to enter the router's web configuration interface.

Follow the default username and password on the nameplate at the bottom or on the manual, and click "Login" to enter the router's web configuration interface.

So if it's not a new one, but a wireless router that has previously modified its IP address, how can you find the forgotten IP address?

Make use of the Knock Command Line Lookup

First, open the Command Prompt window. Right-click the Start button and select "Command Prompt" from the menu. Then, type ipconfig and press enter.

Then look at the default gateway address of the LAN section, which is the login IP address of the router.

The white box is the login IP address of the router.

For example, in the white box, the login IP address of the connected router is displayed as ". Users only need to type the address into the IE address bar to enter the router's settings interface.

Restart the router with the default IP address

You can also restart the router and log in with the default IP address.

Of course, if you want to save trouble, you can also restart the router directly, and then you can use the "use the default IP address" introduced at the beginning, step by step to enter the router settings interface.

First, open your computer browser, and then you can find the address bar above the main interface of the browser.

2. Then, enter " in the address bar at the top and press enter to confirm.

3. Then, enter the account and password of the router on the interface.

Fourth, finally, you can see that the router settings interface appears on the interface, and the problem is solved.

The settings of various brands of routers are much the same.

1.The router is a device that sets up a LAN to achieve network sharing, and the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, and each computer is connected to the LAN port of the router (if it is a laptop, you should also use the network cable to connect one to the router and then complete the parameter setting), the IP address of the computer network card is set to be automatically obtained, and the address bar of the computer browser is entered yes, and the network parameters obtained by your computer network card should be viewed. Log in to the router through the IP address of the gateway, the general username and password are admin, set according to the setup wizard, generally choose the PPPOE method, enter your broadband account and password;

2.If there is a wireless network name or SSID setting in the setup wizard, complete the setting according to the settings wizard prompts, if not, click to enter the router's WLAN settings or wireless settings, there is a wireless network name or SSID, there is a default can also be automatically set, and then enter the wireless security settings, there is a wireless encryption method selection and password setting, set your wireless signal encryption key;

3.If the laptop uses wireless Internet access, the operation is as follows: right-click the online neighbor - properties - right-click the wireless network connection - view the available wireless network, click your wireless network name in the searched wireless network - connection, and enter your wireless network key for verification, after passing the verification, you can connect to the wireless router to surf the Internet normally; If it is a wireless terminal such as a mobile phone or tablet, the same principle is the same as above, and it can be used after searching for a wireless signal and entering the wireless network key to connect.

Do not connect the WAN port of the router, connect the LAN port of the router to the computer, and enter according to the instructions of the manual.

Double-click "My Computer" on the desktop, enter " in the address bar of the page that opens, press Enter, and enter admin in the pop-up box with both the username and password, and you can enter.