I installed a wireless router at home, and the settings were successfully completed, but there were

You click on the computer** data, which occupies the traffic, of course the TV will be stuck, which is normal. The solution is to find out the IP addresses of your computer and TV. Then go to the router settings and make sure that the bandwidth value that the TV can use is OK.

Yes this, turn on IP control, enter your bandwidth, your bandwidth is 10M. Enter the IP of the TV,Settings,Its minimum bandwidth ensures that it can be smooth,I estimate that 4M it can be smooth。

If you have a few m of bandwidth, 4m, it should be okay, the router, you do a speed limit, to ensure a minimum of 2m bandwidth per computer, so that your computer** will free up at least 2m bandwidth for your TV, but your **speed will be slower.

dadequeshixiangxi

This doesn't matter about the router at all. Problems with the network. Your 10m is not up to par at all.

On average, the speed will drop a lot after setting the IP bandwidth control.

Evening rush hour is definitely carded. Playing alone is also a card.

No, the internet speed doesn't work, there's no way to do anything.

It may be caused by the wrong settings of the wireless router, it is recommended to reset the wireless router to factory mode, and then set the corresponding Internet access parameters.

When the wireless router is powered off, hold or hold the reset hole or button on the wireless router for about ten seconds, wait for the indicator lights to turn off and turn on, the wireless router will restore the factory settings, and then connect to the computer for settings;

Any browser on the computer, enter the address bar for specific parameters See the parameters on the back of the wireless router), enter the account and password to log in to the wireless router manager background;

Setup Wizard - Next;

The default wireless router selects the Internet access method, the next step;

Enter the account number and password given by the operator when you report the installation of the network cable, and the next step;

Set the wireless network account (SSID) and encryption password, next step;

Click Done.

Let me tell you how to use the router to connect to the Internet, and you will find it very convenient after using it.

1. Connection: The optical fiber into your home is first connected to the ONT (rented to you by the mobile company, now Huawei brands are the majority), and then the ONT is connected to the WAN port of the router with a network cable (it is best to buy a wireless TP-link, the effect is better, and the mobile phone can be WLAN Internet access), and finally use the network cable to connect to your computer network card interface from the 2nd and 4th ports of the router.

2. Set your computer's IP address to and subnet mask to be, then open the Internet Explorer, enter the IP address, press Enter, and you can see the router's configuration interface.

3. Select the network connection setting option in the configuration interface, enter the username and password (there is a description on the list given to you), remember to choose the PPPoE dial-up method, turn on the DHCP function, and then follow the prompts to complete the configuration.

4. In order to prevent others from rubbing the network, you can set a password for wireless access, which will be more secure.

5. Finally, your computer will be ready for Internet access. If there are two, it will be good to connect to port 3 of the router, and if there are three units, you can continue to connect to port 4. For wireless routers, you can access them via Wi-Fi.

6. Happy surfing the web.

Reset the router and set up the reason why you can't access the Internet:

Cause 1: The network line is faulty.

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Reason 2: The router is misconfigured.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

1. Whether the port on which the router connects to the modem is WLAN;

2. Whether the router is set up to access the Internet correctly, telecom is generally ADSL, it is best to ask the operator;

3. Whether the account password is correct;

4. If there is an IP address in the running status of the router, the bottom display is disconnected, which means that you can access the Internet;

5. Whether the computer IP address and the router IP address are in the same network segment.

The infinity router you bought has an after-sales service. Or set it up yourself in the background. Or maybe the switch on the router doesn't turn on!

After the cable is connected, enter the router settings to see if it is connected, if it is not connected, try to connect it manually, and then it is not connected, there is a problem with the router settings. If the connection is normal, check that the IP, gateway and DNS of the computer are not set, and if the router DHCP is turned on, the computer will be set to get it automatically.

Hello, your problem needs to be analyzed according to the specific situation to know how your route should be connected and set up! And your broadband from the cat out of the network cable to the wan port can not access the Internet, it should be your settings are incorrect, and connected to the lan port can be on 3 computers, if you are sure that in front of your router is a cat, then is it a fiber routing cat all-in-one machine? Do you want to enable routing?

If it is not a routing cat all-in-one machine and the routing function is not turned on, then it is impossible to connect the network cable to the LAN port to enable three computers to access the Internet at the same time! Unless it's the case I mentioned above, or the cat you mentioned in the question supplement, it's actually a router! Please explain your specific situation before you can analyze it specifically, and then you can tell you if the specific connection and settings!

Look at this useless... Your default password is admin account

After entering, click on the setup wizard Next, then enter the correct Internet password and account number, and then set the wireless password of the wireless router Next, restart the router and it's OK··· I hope to adopt...

Connect the network cable on the cat to the WAN port (generally blue, the color of this port is different anyway) and then,Log in to the router on the browser,Set your dial-up account password。。。 Pay attention to the PPPoe method. . .

Then save it, and just restart the route.

Take a look at your local connection, how small the bytes received or sent are, or even 0!

Try slowing it down, and you're good to go!

Secret**Oh, don't forget to add points to encourage if you can!!

Right Health My Computer -- > Properties -- > Hardware -- Device Manager -- Network Adapter -- Select the network card you are on first, and select it from the drop-down menu on the right in the right value drop-down menu"10mbps half dupex"--OK--OK, that's it;

Check to see if your computer's IP address is automatically obtained.

Then, in cmd, type ipconfig renew

There are many reasons for the failure of the router to still not be able to access the Internet after it is set, and it is necessary to test to determine the fault point, and the specific test methods are as follows:

1. Set up the dial-up connection according to the requirements of the operator, connect the stand-alone device to the operator's optical modem, and ping the operator's gateway or DNS server address after dial-up the Internet;

2. If the ping is not working, it means that the operator's external network network is not connected, just call ** to find the operator to report for repair;

3. If ping, the external network network is normal and has nothing to do with the operator's network. If it is different, the fault is on the router, restore the router to factory settings, and then reset the router to eliminate the fault.

4. If the router still fails after step 3 above, you can judge that the router hardware is faulty and you can only replace the router.

Looks like there's something wrong with your setup.

Do you have broadband internet access? How do you set up your routing?

Failure Analysis:

If you change the broadband you apply for at home, you generally need to reconfigure the WAN in the router.

Because if you change broadband, the general broadband account and password are not the original.

Solution: 1. Enter the wireless router management background and select the basic configuration - WAN port configuration.

2. Enter the new broadband account and password, and click Save.

After connecting, you can set it up again.

1. The broadband network cable or the network cable out of the cat is connected to the WAN port of the router, and the LAN port is connected to the computer.

2. Enter in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

If a broadband fault occurs, you can use the following methods to troubleshoot the fault:

1 Use stand-alone dial-up, if you are using a router, please temporarily disconnect the router for testing;

2 Restart the modem and the computer;

3 Re-create the broadband dial-up connection and try to dial again. How to do it: Start the Program Attachment Communication New Connection Wizard.

If the self-troubleshooting still does not recover, you can log in to the mobile phone business hall Customer Service Broadband Fault Report for feedback, and we will get in touch with you as soon as possible.

The Internet access method you route chooses PPPOE, what dynamic IP to choose, and you are not the kind that can be plugged into the Internet cable.

In PPPoE mode, the route will let you enter the username and password of broadband dialing, and restart after the settings are completed.

When you enter the running state, you will see the WAN port, and PPPoE has obtained information such as IP and DNS, which means that the dial-up is successful.

You're connected to the router, and you still use the computer to dial up, isn't it redundant, dialing is to let the routing be completed.

The network cable connection is the WAN of the network cable port of the cat and the LAN port of the router connected to the computer.

The wireless router is not set up.

If there is a cat connected, the cat may need to be restarted.

Problems with wireless settings.

First of all, connect the wireless router to the power supply, plug the incoming cable into the WAN port, and then plug the network cable connected to the computer into a LAN port casually.

Open your computer browser and enter it in the address bar. Enter the corresponding account and password are admin, and enter the router's settings homepage.

After entering the Internet mode setting page, you can see that there are three options for Internet access, and it should be noted that if you use ** line dial-up Internet access, choose PPPoE (ADSL virtual dial-up) dynamic IP, and the general computer can be used directly by plugging in the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

Take the more common dial-up Internet access method as an example to set up a wireless router, and then click "Next." After choosing PPPOE dial-up Internet access, you need to fill in the Internet account and password, fill in the account password provided by the ** business when opening broadband, enter the wireless settings, you can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in casually, and then the mode mostly uses 11BGN. The wireless security option is to select WPA-PSK WPA2-PSK, so that it is secure.

The system will pop up a wizard prompt page with successful settings, click "Done" and the router will automatically restart, at this time you can wait patiently.