How to change the wireless network password at home

The first step is to check the login address.

The login address of the router, also known as the management page address, settings, etc. It is a ** (IP address) that needs to be entered in the browser, and the login address is different for different wireless routers.

So, all novices, please find out the login address of your router first! If you don't know what the login address is, please hold your router in your hand, which can be seen in the sticker at the bottom of the router.

Step 2: Log in to the settings interface.

1. First of all, please make sure that your computer has been connected to the LAN interface of the router with a network cable. If it is a laptop, you can connect the WiFi signal of the router without using a network cable to connect to the LAN port.

Important Notes: 1) Brother Hong used to demonstrate a Huawei Honor router, and its login address is:. When you are operating, please enter the login address of your own router, and do not copy the information in the picture above.

2) If you enter the login address of your router, you can't open the login interface of the router. Students who encounter this problem, don't panic, please read the tutorial below first to see the solution to this problem.

What should I do if the router settings page does not open?

3) If you successfully open the login page, but forget the administrator password (login password), you cannot log in to the settings page. In this case, Brother Hong regrets to tell you that you can't change the wifi password now.

At this time, you can only factory reset your router first, and then reset the Internet access, reset the wifi name and password. For more information, please refer to the following tutorials:

How do I factory reset a wireless router?

How do I reset my router after factory reset?

Step 3: Change the WiFi password.

After successfully logging in to the router's settings page, find and open the option of Wireless Settings or Wi-Fi Settings, and you can change the WiFi password.

Important note: 1) In order to avoid being rubbed on the network, the wifi password is recommended to be set with a combination of uppercase letters + lowercase letters + numbers + symbols, and the length of the password should be greater than 8 digits.

2) If only the wifi password is changed, the wifi name is not changed; There may be a problem that wireless terminals such as mobile phones and laptops cannot connect to the wifi signal.

If you encounter the problem of not being able to connect to the wifi signal, you don't need to worry, you just need to delete the wifi cache records in the mobile phone and computer first, then reconnect, enter the modified wifi password, and the connection can be successful.

How to change the wifi password at home.

Here's how:

Step 1: If you want to change the password of the background management of the wireless router, it is recommended to connect the computer with a network cable. After the computer is successfully connected, check the obtained default gateway IP

Step 3: Enter the correct username and password to enter the background management interface.

Step 4: Click on the "Tools" tab and enter the old and new passwords in "Manager".

Step 5: After clicking the "Execute" button below, the router will ask you to re-enter the username and password, which is the changed password.

Step 6: After re-entering the router background management interface, we directly click on the "Wi-Fi" button on the left side under the "Home" tab.

Step 7: Enter the password we want to change in the "Share Password" field below, and it is recommended to change the SSID at the same time.

Step 8: Click the "Execute" button below, the router will prompt you to wait for a certain amount of time, and will display "Reactivate", click the "Continue" button or close this window.

A network password is a technique used to obfuscate users who want to turn normal (identifiable) information into unrecognizable information. But this unrecognizable part of the information can be reprocessed and recovered and cracked. Password is a generic term for "password" in Chinese.

A password is a symbol that is coded according to a specific law to transform the information of both parties to the communication. In other words, a password is a sequence of symbols that conceals the real content. It is to transform the information expressed in the open and standard information code into an information code that cannot be read by anyone other than the two parties to the communication, and this unique information code is the password.

If it's tp link

Follow the steps below to change the wireless password.

Note: Please read the full text before operating, please prepare the network cable before the operation, to prevent the wireless device (referring to the computer) from being unable to access the router, Intel's wireless equipment (i.e. Centrino) please mistakenly upgrade the software driver to the above version, otherwise TP-Link will not be recognized, the bug has been determined to be TP Link has been submitted by my diagnosis, but there is no technical reply from the technician.

1.Open the browser and press enter in the address bar to pop up a password prompt.

2.Enter the username and password in the password prompt window (the default is admin, if there is a discrepancy, the corresponding value should be given under the router) and press OK. At this time, the setup wizard pops up and two web pages on the setup interface are opened, the setup wizard can be closed, and then enter the specific wireless setup section.

3.Click Wireless Parameters in the left list to go to the Basic Wireless Network Settings page.

4.On the right page, you can see some basic parameters.

You can fill in your favorite name or not, and the purpose of the modification is to make it easier to connect with others when setting up the wireless device.

Make a distinction between bands that have more than one around.

(generally set relative to other people's routing frequency band 3, it is not recommended to use the 13 frequency band, because some mobile phones or PDAs with WiFi function cannot recognize this frequency band).

Make sure to turn on the wireless function; Turn on security settings are ticked (SSID broadcast is allowed) It is recommended that beginner players tick to prevent themselves from forgetting the router.

cause unnecessary trouble) and set a password.

General household. Type selection"wep", select Auto Select for Security Option, and select ASCII Code for key format (

It's more cumbersome, and it's hard to remember passwords).

Select a corresponding value for the key type after key 1 (128 bits recommended).

Fill in your password in the box corresponding to the key content, and make sure that the number of characters cannot be more or less.

Select a 64-bit key.

10 digits, or ASCII

5 symbols. Select 128-bit key.

26 numeric characters, or ASCII

13 symbols. To select a 152-bit key, you need to enter 32 hexadecimal digits, or ASCII

16 symbols. 5.Make sure that the above setup steps are completed and press the "Save" button, and the wireless router part of the setup ends here.

The settings on the computer are basically the same as those without a password, except that they are entered when prompted.

and password (please translate the English version by yourself).

How do I change my wifi password? Many friends will encounter such a problem, the wifi password at home is forgotten, and they can't remember. Life without the internet is really too hard, what should I do?

When using a wireless router, there are three passwords involved: wireless password, router management password, and broadband password.

1. Change the wireless (wifi) password.

The wireless password is the password that needs to be entered when the wireless terminal connects to the wireless signal, and the wireless router does not have a wireless password when the wireless signal is in the default state of the factory. Here's how to change the wireless password:

1. Log in to the management interface.

Open the browser, clear the address bar, enter, some routers are, enter the management password in the pop-up prompt box; Note: The management password is set by the user, if you forget the password, please restore the router to factory settings and set it again;

2. Set a wireless password.

After entering the management interface, modify the wireless password on the right side of the interface, click Save, and the new wireless password will take effect immediately. For some older versions of routers, you can set and change the PKS password in the wireless settings and wireless security settings interfaces, and click Save after the settings are completed. Some routers need to be restarted for the settings to take effect, please follow the prompts on the page.

Note: If you only change the password but do not change the wireless name, the terminal that has been connected to the signal before needs to delete the wireless configuration file before it can connect to the signal normally.

2. Change the management password of the router.

The management password is the password that you need to enter when you log in to the router management interface.

Modification method: Log in to the router interface, click Route Settings, Change Administrator Password, Enter the original login password, set a new management password, and click Save. For some models of routers, modify the system tools and modify the login password interface on the management interface, and click Save after the settings are completed according to the prompts on the page.

3. Change the Internet broadband password.

The broadband password is the password for broadband dial-up Internet access, which is provided by the broadband operator, and only your broadband password can be entered in the router.

Setup method: Log in to the router interface, click on routing settings, Internet settings, select broadband dial-up Internet access, enter broadband and broadband password, click to connect, and wait for the IP address to be obtained successfully.