Glash tte watches are not allowed to be repaired

Five common reasons for the time error and inaccuracy of Glashütte watches:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services. Yes[8th Floor, Block E1, Oriental Plaza Office Building, No. 1 East Chang'an Street, Dongcheng District, Beijing].Dispose.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

Mechanical failures such as magnetism, lack of maintenance, malfunction of the watch hairspring, escapement system, slippage of parts, etc., can cause the watch to be fast and slow. Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc.

Five reasons for watch time error and watch time inaccuracy:

1: Insufficient power reserve.

2: The battery is insufficient.

3: Having been hit or impacted.

4: Maintenance is required.

5: The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate.

Lack of oil, magnetism, vibration, and damage to parts are all possible, so take it for a comprehensive maintenance and check it to know what the problem is.

Glashütte Watch Care Center: 400-659-0877

In order to maintain a malfunction such as the rapid operation of a mechanical watch, degaussing should first be carried out, completely and neatly; Then check the position error of the watch, then check the hairspring, clean the hairspring with alcohol, the fuel will become cleaner, volatile and inferior fuel, the magnetic field will make the hairspring appear in a ring shape or attract each other.

It could be a hairspring failure. The hairspring is part of the structure of the watch, it mainly affects the accuracy of the watch, it is elastic, it is an extremely delicate element in the watch, it is used to control the balance wheel to do isochronous reciprocating motion. The change of the effective length of the balance spring determines the moment of inertia and the amplitude period of the balance wheel, and the balance spring is also one of the factors affecting the accuracy of the time.

The fixing point of the inner and outer ends of the hairspring is also an important factor affecting the accuracy of the timekeeping.

1.Insufficient power: mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of movement, and it can be directly manually wound to supplement the power.

2.No maintenance: mechanical watches are generally maintained once every 2 to 3 years, the watch is used for a long time, the lubricating oil in the movement will dry up, and the friction of each gear for a long time will produce iron filings, increase the friction between the gears, this kind of problem only needs to clean the movement, re-refueling.

3.Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop.

According to the reason why the watch is slow, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the watch waterproof, shockproof and anti-magnetic, and send it for repair in time if there is a problem.

1.Insufficient power reserve.

2.The battery is low.

3.Having been hit or impacted.

4.Magnetized.

Magnetism on the watch or slippage of internal parts of the watch can cause the hands to fail to move or move incorrectly. The sludge is dry: Glashütte is full of oil, and prolonged use produces sludge.

If the Glashütte is run for a long time, if the Glashütte is not opened, cleaned and maintained, the oil sludge produced in it can condense and cause the Glashütte to stop operating.

The main reasons why the watch does not go are: the movement gear is misaligned, the watch is magnetized, bumps, and the oil sludge is dried for a long time when it is left on hold. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours. Quartz watches, on the other hand, can be actively wound and should be worn on the hand for more than 8 hours a day to replenish the mainspring.

Lack of exercise after wearing it will also show that the watch does not move or stop.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

1. Open the back cover to check the movement and adjust the speed and slow needle of the hairspring. If the hairspring is made longer, the watch will go slower. The shorter the balance spring of the watch, the more often it oscillates back and forth, and the faster the watch will go.

If the balance spring of the watch is made longer, the frequency of the balance wheel oscillation of the balance spring will be reduced, and the watch will go a little slower. If you are not confident enough in your craftsmanship or still do not improve, it is recommended to go to a professional watch repair center to let the watch masters take a look, so as not to mess up, resulting in a short hairspring, and it will be more difficult to repair at that time.

Second, for the maintenance of such faults as magnetization, demagnetization first, be sure to demagnetize neatly and thoroughly, you can buy a special demagnetizer for watches as a good helper; Then check the position error of the watch, continue to check the hairspring, clean the hairspring with alcohol, it will be more fuel and tidy, volatile is good, and the low-quality fuel and magnetic field will make the hairspring show up to circle or attract each other.

It is best to do a timekeeping quiz on the repaired watch, and it is best to do a long-term dynamic check to see which all-round rotating experimental rack is to be put on, or to wear it directly to check carefully. And those hidden deep faults, we can only pin our hopes on experienced professional watch repair masters.

If the watch you just bought is fast, then it is likely to be magnetized. Because after the hairspring is magnetized, the circle between the rings is only shown when wearing, there is a sticky or short loop, especially in the façade, the hairspring will hang down due to its own gravity, and the shaking of the arm will aggravate its radial movement, resulting in fast walking.

Here should be sent to a professional repair shop with a professional demagnetizer to demagnetize it, do not be greedy to go to the roadside stall for maintenance, so as not to repair the more bad, in addition to the watch demagnetization does not need to disassemble the watch, the cost is generally not high.

Your Glashütte watch is not on time, in this case, you can go to the watch repair shop on the first floor of China Resources Vanguard on Dongge Road in Nanning to get it repaired.

After this watch is not implemented, you went to find him from the watch you bought? The shop asked him to continue repairing, which was more cost-effective.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

The name is to be used in the oversized supermarket to sell the target industry, it has a repairman, you can look it up there and consult.

There are many reasons why the watch is not accurate, and you need to take it to the after-sales service center for testing.

The address of Chengdu is in Room 05, 24th Floor, Sichuan Aviation Plaza.

My Glasti watch can't go anywhere, there is a repair shop at the third traffic light in Langdong District, Nanning, and the technical level of the master here is still good.

Glashütte Watch Repair Center: Room 01, 20th Floor, Yingli International Financial Center, No. 28 Minquan Road, Yuzhong District, Jiefangbei, Chongqing.

If it is a new watch that you just bought and the strap is broken without wearing much, then you can go to the aftermarket to replace it. Generally speaking, the warranty period of the watch is 2 years, and although the strap is not covered by the warranty in many cases, it can also be found after sale for those who have just bought it.

If the strap of the watch that has been worn for a long time is broken, then it can be taken to a special maintenance point for repair according to the specific situation, which is also more convenient.

Different brands of different styles and different price points of watches, watch straps are also different, there are leather, there are steel, but also chains, etc., for the belt to break it also depends on what the situation, if it is really serious, there is no way to repair, then it can only be replaced with a new one.

If the watch is the kind of decorative strap, usually the kind of chain, then if one of the sections is broken, you can completely remove it and don't want it, and then re-buckle it, which is similar to many people's bracelets.

The watch is worn on the wrist and neck, which is very convenient to look at, but once you find that you want to disconnect it, you need to find a way to solve it. It's better to be leather, and you can glue it up by yourself if it cracks a little, so it won't be so easy to break it all.

Since the maintenance requirements of each strap are different, you need to choose a watch according to your own needs. For example, leather straps are very high-end, and they can show a unique personal temperament, but they are very unsuitable for summer wear, because the sweat in the human body is very corrosive to the strap, and it needs to be maintained accordingly.

If the warranty period has not expired, it is recommended that you get a special after-sales service center, if the warranty period has passed, you can also choose to get some professional and regular watch repair shops to repair.

In fact, it is a very normal phenomenon for the watch to fall off. That's because we often use the handle of our watch to adjust the time. It is the most frequently used watch part in our daily life.

There are two cases when the handle of the watch falls off. The first case is actually not very complicated, it is simply the shedding of the crown. Not with the barbar.

The second type of shedding is the shedding along with the bar. The first occurrence of this situation is usually the rust of the head. Fracture caused by the impact of an external force.

The second case is more complicated. It is possible that the movement inside the watch has fallen off.

The Glashütte watch repair location is located in Room 04-05, 11th Floor, Office Building, South Tower, Hong Kong Plaza, No. 283 Huaihai Middle Road, Huangpu District, Shanghai.

How to deal with water ingress into the watch:

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient, and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water more than 100 times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used repeatedly and repeatedly.

Method 2: If the mechanical watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it at about 15 cm near a 40-watt light bulb, and bake for about 30 minutes, and the water vapor in the table can eliminate the problem. Do not bake the watch close to the fire, so as not to deform the watch by heat.

If there is water in the watch, you still have to go to the repair shop to wipe the oil and repair it to prevent the parts inside from rusting.

Water ingress into the watch is a common fault of the watch, and it is also a very harmful failure.

Water ingress of the watch may cause rust on the internal movement parts of the watch, although the watch parts are now treated with anti-rust, but some tiny parts are still easy to rust, so it is better to repair the watch as soon as possible once the watch is flooded.

If other liquids are introduced, such as seawater, which are more corrosive, then the corrosion will also be faster.

Generally, the light bulb on the Internet, the sun is scorching, the watch is dried by body temperature, hair dryer, desiccant and other methods are not advisable and unsafe, if the value of the watch is higher, it is better not to take risks.