How to build tiles, how to build brick walls?

Method of laying tiles.

A combination of basic paving methods. The most common paving method is the tile joint straight paving, rectangular wall tiles can be paved vertically or horizontally, oblique paving is also a habitual technique, the effect is very good, but only suitable for square tiles, some people like to stagger the tiles, into a special I-pattern. Straight and diagonal paving are often used in combination.

Embellishment of threads and floral pieces. Generally, only one decorative line is used on the wall of the space, which is arranged at a position of meters to 1 meter from the ground, also known as the waist line. It is better not to disconnect the waistline.

You can also use two waist lines, arranged at a position of 2 meters from the ground, if you want to pave more waist lines, you should choose different thicknesses and styles, otherwise it is too cumbersome. The flower piece usually serves as the finishing touch, and is used in the eye-catching area above the waistline of the wall. It is not very refined, but can be regularly distributed one or two pieces on each wall.

Handling of color-blocking. The contrast of the colors of the tiles gives a strong first impression. It is usually based on white or other light colors, and the color of the tiles used for color matching is slightly darker, and it is commensurate with the color of the flower pieces and decorative lines, such as white and blue, beige with light brown, etc.

There are ways to block color, which can be lined with another slightly darker color below the waistline; You can also use two-color tiles to play the grid, and the specific spelling depends on your personal thoughts.

Precautions. Before the tile is paved, the water should be blistered, how much can be constructed, not all at one time, and the water should be combined with the construction progress of the workers. Due to the improper mixing ratio of cement and sand or the high cement marking, the proportion of cement is large, the adhesion of ceramic tiles is strong, and the bricks can be quickly sticked, but the cement mixing ratio is high, and the expansion coefficient of cement mortar is large, and it is easy to squeeze the bricks after paving.

The recommended ratio is 1:3 for wall tiles and 1:1:for floor tiles

2--3, the cement number of cement is the number of cement. Be careful not to destroy the glaze layer of the tile, pay attention to the gap when linking, not too small.

Depending on your preference, you can use tiles as cabinets.

First, the selection of materials. The tiles that can be made of brick cabinets are quite exquisite. For example, in terms of specifications, it is thicker than ordinary tiles; In terms of design, sufficient preparations should be made before production, and the corners of the corners, yin corners, yang corners, and bricks used for color jumping should be matched, otherwise, there will be no effect.

2. Space. Brick kitchen cabinets are very picky about the owner's taste, the height of the house, and the size of the kitchen space, such as the floor height is below the meter, and the kitchen area is less than 7 square meters. Therefore, ceramic tile veneered kitchen cabinets are more commonly found in Western-style kitchens in villa residences.

3. Construction. Brick kitchen cabinets can not be like other kitchen cabinets, only according to the owner's choice of cabinet parts, the site can be assembled and installed as a whole, but it needs to be made with mud and sand, on-site construction can be done, and the construction skills of workers are also a huge test, no matter how beautiful the design is, the quality is not good.

Is it OK to build cabinets with bricks?

Key points of brick cabinet construction design:

1. Considering that the tiles are directly glued to the wooden frame, they may not be firmly glued, so they are often directly built into a frame with cement mortar, and then the tiles are pasted on it.

2. If you are making kitchen cabinets, you can first apply cement mortar on the surface to enhance the adsorption force of the tiles, and then stick the tiles on it.

3. Is it good to build cabinets with bricks? In terms of process treatment, the kitchen cabinet designer should also check the construction progress of the workers on site. For example, in the villa, there are generally three to five hooks; The gaps between bricks and bricks are hooked with coarse sand, so that the natural feeling can be shown, and the style is so unified.

4. Is it good to build cabinets with bricks? In the kitchen cabinet of this material, the hand-painted tiles often play the role of the finishing touch, if you feel that the antique bricks of the whole color seem monotonous, you can use hand-painted tiles, or jumping tiles to make some jumping patterns in other parts to activate the whole space.

The floor tiles should be paved with cement mortar first, and the uncoated cement tiles should be laid on the ground, and after knocking out, the cement slurry should be coated all over the floor tiles and paved on the ground, and the diagonal position of the four bricks should be flush. And the order of laying is also exquisite. If the ground has a slope or a floor drain, attention should be paid to finding the slope according to the drainage direction; The wall tiles should be paved from the bottom up, and for the sake of aesthetics, the bottom bricks should be pasted later.

After the wall tiles are pasted, press the floor tiles. In addition, a wall should not be pasted to the top at one time to prevent the tile from falling due to its large weight. Do not step on the floor tiles for a short time after laying them.

1 You need to prepare a hammer, chisel, cement, sand, first use a chisel to remove the cement ash of the fallen tiles, and then set the tiles with ash.

The masonry of brick masonry is as follows:

1. One shun and one ding. It is made of a skin along the brick, a skin of bricks at intervals, and the vertical ash joints of the upper and lower skins are staggered 1 4 brick length, which is a commonly used way of assembling, which is characterized by a skin along the brick (the long side of the brick and the brick parallel to the length of the wall), a skin of brick (the brick of the long surface of the brick and the brick perpendicular to the length of the wall) are built at intervals, and every other skin of bricks, Ding Shun is the same, and the vertical joints are staggered. This masonry method has good integrity and is mostly used for a brick wall.

2. Three shun and one ding. This is the most common form of masonry, made of three skin bricks, one skin brick assembly, the upper and lower skin along the brick lap half brick length, the Ding brick and the brick lap 1 4 brick long, because the three skin along the brick inside the longitudinal joint, so the integrity is poor, and the wall is not easy to control the straight. However, this method of assembling bricks is fast.

3. Plum blossom dice. This masonry method is also known as sandbag type, which is built at intervals between bricks and bricks in each skin, and the vertical joints of the upper and lower bricks are staggered with each other 1 4 bricks long. The internal and external vertical joints of this masonry method can be staggered for each skin, and the integrity is better.

4. Two flat sides. Two flat side is also called 18 wall, and its assembly characteristics are, the staggered joint between the upper and lower skin of the flat masonry layer is half a brick, and the staggered joint between the flat masonry layer and the side masonry layer is 1 4 bricks. This masonry method is more labor-intensive and inefficient, but it saves bricks and can be used as a load-bearing wall for buildings with smaller floors.

5. Smooth method. This method is only used for building half-brick thick walls.

Summary. Dear, you can deal with it in the following ways. 1. Start knocking from the center with a steel hammer, pay attention not to damage the surrounding tiles when knocking on the edge, and then use a cutting machine to remove the cement of the adhesive layer, and then you can remove the tiles.

2. If you only change the middle tile, you can use a hammer to break the floor tile from the front, and then clean up the broken tile slag, and then replace it with a new tile. 3. If the floor tile is hollow, you can use a rubber hammer to gently knock it, add water while knocking, until the edge is loose, you can use a rubber hammer to pry it from all sides, and it should be noted that the concrete under the floor tile should be knocked off a layer and then paved with new tiles. 4. If it is a freshly paved tile, it is easier to deal with, you can directly use the magnetic sheet machine to open a small circle of mouth, and slowly knock it up, if the cement slurry has not dried, you can directly shovel it with a shovel.

Hello dear. What you are consulting is how to put another layer of tiles on top of the tile, right?

Lay bricks and cement on the floor tile surface, knock it off, and the tiles should not be broken.

Dear, you can deal with it in the following ways. 1. Start knocking from the center with a steel hammer, pay attention not to destroy the surrounding tiles when knocking on the edge, and then use a cutting machine to remove the cement of the adhesive layer, and then you can remove the tiles. 2. If you only change the middle tile, you can use a hammer to break the floor tile from the front, and then clean up the broken tile slag, and then replace it with a new tease.

3. If the floor tile is hollow, you can use a rubber hammer to gently knock it, add water while knocking, until the edge is loose, you can use a rubber hammer to pry it from all sides, and it should be noted that the concrete under the floor tile should be knocked off a layer and then paved with new tiles. 4. If it is a freshly paved tile, it is easier to deal with, you can directly use the magnetic sheet machine to open a small circle of mouth, and the slow travel refers to Li Slow to knock it up, if the cement slurry has not dried, you can directly shovel it with a shovel.

In the kitchen, I built a water-surrounding one, so I can't let the water flow into the other place, so now I have to knock out the small pool around the water, and it's so troublesome and noisy, can there be a simple solution?

It is difficult to operate according to your requirements without damaging the floor tiles.

This way you can only use a percussion drill to play slowly.

The common methods of brick wall masonry mainly include: one ding and one shun method, one ding three shun method, one ding five shun method, multi-layer one ding method, flat brick ding staggered joint method, flat brick staggered joint method, side brick masonry staggered joint method and so on.

1. When building a wall with bricks, the bricks placed in the direction of the width of the building are called "bricks", and the bricks placed in the direction of depth are called "bricks".

A Ding shirt Hui and a shun method, that is, after building a brick, and then put a brick, the brick and the brick are staggered.

2. The method of one ding and three shun is to build a brick after masonry, and then build three bricks in a row.

3. One Ding Five Shun method, that is, after building a Ding brick, and then building five bricks in a row.

The above three bricklaying methods are both Ding bricks and smooth bricks for each layer.

4. The multi-layer method is different from the above three methods.

It is placed after the masonry of multiple layers of bricks, and then a layer of bricks.

5. Flat brick and Ding masonry staggered joint method:

Flat bricks are to lay the bricks flat. Ding masonry is to place bricks along the direction of the depth of the wall. Staggered joints are the staggered gaps between the upper and lower bricks.

The walls built by this method of masonry are very thick and are mostly used for city walls.

6. Flat brick staggered joint method:

It is similar to the staggered joint method of flat brick masonry, except that the bricks are masonry in the direction of the width of the face.

7. Staggered joint method of side brick masonry:

The bricks are staggered up and down according to the width of the wall, and the side façade of the bricks is facing down.

The walls built by this method are very thin and cannot be used for load-bearing splendors.

There are many ways to lay bricks, and here are the most commonly used ways to lay bricks, a total of five methods:

Cis-type is also known as strip masonry, this masonry method is along the brick assembly of each skin, the strip surface of the brick is exposed, the upper and lower skin left and right lap is half a brick, the staggered joint is 120, suitable for the masonry of the half-brick wall and the modular perforated brick.

A shun and a ding style is also known as "full of Ding full strips", which refers to a skin of bricks in accordance with the way of a skin of bricks and a skin of bricks alternately masonry, a layer of bricks, a layer of bricks, alternate arrangement, repeated combination. In the corner part to add a brick (commonly known as a seven-point brick) to carry out staggered joints. This masonry method is characterized by good lap joint, no through joint, strong integrity, so it is widely used.

Each layer of bricks has Shun Ding, search which upper and lower layers are staggered, each layer of Ding bricks and Shun bricks are separated, the upper layer of Ding bricks sits in the lower layer of bricks, the vertical joints between the upper and lower layers are staggered with each other about 1 4 bricks long, this decorative effect inside and outside the vertical joints can be staggered up and down each layer, so the integrity is better, the hook joints are neat, very beautiful, also known as the Shun Ding interphase masonry method.

The "three shun and one ding" masonry method is three layers of bricks and a world yard layer of bricks are built at intervals with each other. The upper and lower layers are staggered 1 4 bricks long. Suitable for wall thicknesses of one brick and more.

The "whole ding" masonry method is all made of bricks. The upper and lower layers are staggered 1 4 bricks long. It is only used for masonry arc masonry.

Walls or parts where scaffolding eyes are not allowed:

120mm thick walls, independent columns;

Window wall with a width of less than 1m;

Within 200mm on both sides of the door and window openings and 450mm at the corners;

Beam or beam pad and within 500mm to the left and right;

The range of triangles on the lintel at an angle of 600 and the height range of the net span of the lintel 1 2.