How to transfer a game to another computer after connecting 2 computers with a single network cable

Windows XP uses network neighbors in the local area network to communicate with each other, share file transfers, and share printers (similar to other systems) (all computers to be shared must be set up).

1. Open a guest

Control Panel User Enable guest account).

2. Set up in the same working group.

Right-click on the My Computer Properties Computer Name to Change Workgroup (Reboot Required).

3. Install the network "service" protocol.

Control Panel Network Connections Right-click on the "Local Connection" property General and directly click on "Install Services).

4. Run "Set Up Home and Small Office Network" once

Control Panel Network Installation Wizard; or Online Neighbor Set up a home and small office network) to enable shared files.

5. Share the file or folder you want to share.

Right-click the folder you want to share, select "Sharing & Security", and check "Share this folder on the network"; Or copy the file you want to share to the shared document).

6. Share the printer.

Right-click on the printer you want to share, select "Share" and check "Share this printer") After connecting, enter his IP in the address bar to access his shared (that is, the IP in the local connection properties).

When setting the IP address in the local connection attributes, it is best to set it manually and do not obtain it automatically.

Click on Online Neighbors - Look at the workgroup computer to see it.

！！Two computers are connected with network cables, so how can it be transmitted, there is no route to run these transit protocols, it is impossible, the two computers can only be directly connected through the serial port, but the speed of the serial port is quite slow, no one uses it, only special occasions are used, you want to transmit two computers, it is estimated that you want to use the local area network, how to do without basic middleware? At least one router is in a local area network, if there is no router, how can the machine be recognized?

None of your IPs fainted.

Under the condition of the router, you can use LAN transmission software such as Feiqiu But in the transmission of 4G large files, the probability of error is still very high My experience of using it is like this. Hope it helps,

Using the "Flying Pigeon Story" software requires both computers to have a very fast speed, and the software is green and small in size.

Just create a shared folder.

The method of direct connection between the two computer network cables is as follows:

1. To set the computer IP, first open the interface below and click Local Connection. (as shown in the picture below).

2. Then we click on the Properties option. (as shown in the image below).

3. Click on the selected option in the figure below. (as shown in the image below).

4. Set the IP address as shown in the figure below. (as shown in the image below).

5. At this time, after the first computer IP is set, we will set the second computer IP. (as shown in the image below).

6. Right-click the folder, select Properties, and click Advanced Sharing in the Properties panel. (as shown in the image below).

7. Then check Share this folder. (as shown in the image below).

8. Then we set up the permissions. (as shown in the image below).

9. Win+R brings up the running window, and enters the IP set by the computer in front of the input box, and the format is as follows. (as shown in the image below).

10. Enter to confirm, enter the username and password of the previous electric limb brain, we can see the folder of the shared Luxiang in the open interface, note that here is the username and password of the computer that sets the shared folder so that we can access the files under the folder. (as shown in the image below).

Connect two computers with a network cable Speed:

According to the situation of the network card, it is generally 10m per second, the fastest is 20m per second, that is, 20000 per second, 10g is 500 seconds, if it is 10m, the slowest is 10 minutes, we have proved in practice that it is about 10m, and the start and end will be slower. <>

Tools Raw materials.

Two computers.

One network cable. Steps: 1. Connect the two computers directly with network cables.

2. First computer settings 1: Open the settings panel.

4. The second computer also opens the settings.

5. The second computer, then open cmd and ping the first computer. Keyboard "windos key+r" and type cmd and press enter. If there is time to return as shown in the figure on the right, it means that the two computers are successfully connected.

6. Then find the file you want to transfer: for example, the file "test" on drive D.

7. Then click in the order in the picture.

8. The following dialog box appears:

9. Turn on the second computer and enter the address to access.

10. Enter the folder shared by the first computer.

Note: If you want to enter the account password, enter the account password of the computer you want to access, and if the computer you are accessing does not have an account password, you can create one.

Docking between two computers with network cables (twisted pair cables, 1 3 2 6 switching), the specific steps are as follows:

1. Make a [twisted pair], and the end of the crystal head is arranged in the order of white orange, orange, white green, blue, white blue, green, white brown, and brown. The other end is in the order of white-green, green, white-orange, blue, white-blue, orange, white-brown, and brown. Don't make the wrong arrangement!

If you really won't buy one, it's 3 yuan.

The other computer is set as above, but the IP address cannot be the same, you can change to share files between the two computers.

Then you do the root cascade line, the two ends are standard A, the other end is standard B, and then the network card is configured with the same network segment.

For direct connection, a cross line should be used, with 568A at one end and 568B at the other