What are the tricks for dealing with water entering the watch?

If water accidentally enters the watch, you can put a granular substance called silicone and the watch with water in a closed container, and the water will disappear after a few hours. This method is simple and economical, and does not harm the accuracy or longevity of the watch. After multiple water absorption, the silica gel can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used repeatedly.

Put it on the radiator (or under the sun) and slowly dry it for two days and it will be fine, I have a meter after the water enters, so I treated it like this, nothing abnormal, and it has been used normally to this day.

If you can't wait, you can also use a hair dryer to dry it slowly, but it is easy to blow moisture into deeper parts, and the gains outweigh the losses. So you have to be very careful, blow it for a while and let it dry for a while, and take your time.

Dry it with a hair dryer and wrap it in paper. Then put it in the fridge and you're good to go a day later! Thank you.

I've also had this experience, and now that the weather is warmer, you can wrap it in paper and put it in the sun. If there's no sun, use a hair dryer! Hope it helps.

Open the back cover first, take off the battery, and then use a hair dryer to blow it slowly, and "Use the cold wind" to blow is almost the same, put it down for half an hour, and then put on the battery.

Blow dry in a hair dryer, wrap in a paper towel and put in the refrigerator for another day.

Disassemble it and dry it with a hair dryer.

The watch can be placed in the tea cheeks.

Napkin wrap absorbs water for a longer time.

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear.

Method 2: If the mechanical watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it at about 15 cm near the 40-watt light bulb, and bake for about 30 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

If there is water in the watch, you still have to go to the repair shop to wipe the oil and maintain it to prevent the parts inside from rusting.

<><Daily repair methods for water ingress in the watch:

1. Dry the granules with silica gel.

If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. After absorbing water many times, the silica gel can be dried at 120°C for several hours, and the water absorption capacity is renewable, and it can be used repeatedly after rotting and withering.

2. Bake with a light bulb.

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards.

You can also put the mask facing inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after an hour of rumbling on both hands. If the water ingress is severe.

4. Send the watch shop to wipe the oil.

None of the above three methods can remove water vapor, so you should immediately send it to a watch shop to wipe the oil to remove the moisture from the movement to avoid rust on the parts.

5. Bake with a light bulb.

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

6. Blow with a hair dryer.

Dry it with a hair dryer, the temperature should not be too high, the wind is mild, and you know that you can't see the water on the glass.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts. Remember not to disassemble the movement yourself, so as not to damage the movement, and then repair it will be more time-consuming, laborious and costly.

Normally, after the watch is flooded, it is also necessary to look at the severity of the water. If the water ingress of the watch is not too serious, but there is fog in the glass layer, at this time, we directly use toilet paper, or a more absorbent flannel cloth to wrap the watch tightly, and put it on the light bulb to bake for 30 minutes. In this way, water vapor can be effectively removed.

01 If it is said that after the watch enters the water, some friends directly use the open flame to bake. Often, this approach is not very reasonable. This is because if you bake the watch directly over an open flame, it will deform when heated.

02 Of course, we need to pay attention to the fact that the water ingress of the watch is more serious, so we need to send the watch to the watch store to wipe the oil, and remove the moisture of the watch movement in time and effectively to avoid damage and rust of the watch parts.

03 Of course, after the watch gets into the water, you can actually put it directly into the vent and gently wipe it with a dry paper towel. Under normal circumstances, if you put it in the vent for a few hours, you will find that the water ingress inside the watch has improved, or even the water ingress has disappeared.

04 Friends need to pay attention to the fact that after the watch is in water, it is usually not allowed to be exposed to the sun. Because if it is exposed to sunlight, it may cause water mist to reach the inside of the movement, which will have a great impact on the watch.

You can solve it by yourself, the method is as follows, 1. Baking, pull the crown of the watch to the first or second gear, wrap it in a paper towel or cloth with strong water absorption, and then use a 40W incandescent bulb (anyway, it can heat up), or under a strong sun, observe while baking, and the fog can be removed in about half an hour. 2. Dry the blower, prepare a hair dryer, first fix the mechanical watch sideways, the back cover of the mechanical watch is generally a stainless steel cover (of course, there is also a see-through cover), the crown still has to be dialed out, after the hair dryer is energized, adjust to low gear (the temperature is not too high, it is easy to scorch the internal parts of the mechanical movement, and the wind speed is not too large), blow on the metal position, and use the thermal conductivity to make the temperature in the movement rise, the moisture vaporizes, and is discharged with the gap in the crown. This method can be reused to ensure that all the moisture in the movement is removed.

1. Wrap the watch in a clean soft cloth or paper towel, and then place it next to the hot bulb, don't get too close, and observe while baking, so as to remove the fog in the watch.

2. Put the watch in a container that can be sealed, and then put the desiccant and the watch together, the desiccant can be prepared more, and the container can be sealed, so that the fog inside the watch can be removed.

3. After the mobile phone enters the water, you can use a hair dryer to dry, the watch is the same, after the watch enters the fog, prepare a hair dryer, use the hair dryer to blow on the back cover or side of the watch, the wind speed is not too large, and the temperature is not too high, use the thermal conductivity of the watch to evaporate the fog inside, and you can remove the water inside.

If your watch accidentally gets into the water, then you might as well try the above solutions, I hope it can help you.

If you are using a vivo watch, wearing the watch for hand washing, swimming, etc., water droplets may enter the speaker opening of the watch, it is recommended to throw out the water droplets from the watch speaker with a little force, and then wipe the body with a clean soft cloth and wait for the water droplets to evaporate. If the watch cannot be used normally, please go to the vivo customer service center for testing.

Customer service center address: enter the vivo official website vivo**app--my--service outlets after-sales outlets--select provinces and cities to inquire about the customer service center address) It is recommended to call the customer model Kaifeng service center in advance to confirm relevant matters and understand the working time, so as not to delay the precious time between grandchildren.