How to solve the problem of slow toilet draining without suction

1.First of all, clean the toilet bowl and drain the water in the sink (with a rag - suck it out again and again, wring it out) so that the hydrochloric acid is not diluted after pouring it.

2.Pour the whole bottle of dilute hydrochloric acid (about 500ml) into the toilet sink, do not dilute with water, the pure descaling effect is good, and the ceramics will not be damaged. At this time, you will find that the acid enters the tank and reacts with the scale, turning up the bubbles, so after adding the acid, you should use a waste rag to plug the groove, so that the bubbles generated by the acid will turn down as much as possible, so that the scale inside the siphon pipeline will be cleaned more cleanly.

At first, there will be some smoke and strong smell, so it is recommended to turn on the exhaust fan.

3.Wait for half an hour, clean the scale, and then flush the water, and the toilet drain is smooth and powerful.

The toilet drains slowly and there is no suction, and the solution is as follows

1. It may be caused by the low water level of the toilet, we can take off the toilet tank cover, take out the inlet valve, rotate the inlet valve to the right to adjust the height, and then install it back.

2. The damage of the toilet seal will reduce the pressure, which will lead to insufficient suction power of the toilet, and the flushing will naturally be weak. We can remove the sealant at the bottom of the toilet, lift the base of the toilet to replace the seal, and then reseal the toilet.

3. The toilet is not installed properly, resulting in a part of the drain being blocked, which will also cause such a problem. You can remove the sealant at the bottom of the toilet, reinstall and fix the toilet drain with the sewage outlet, and then fix the toilet base with glass glue.

4. Damage to the toilet tank accessories will also cause the toilet to flush weakly. You can remove the toilet tank cover, carefully inspect the toilet water parts, and replace the damaged water parts.

Flush toilet drains slowly and has no suction:1. The amount of water in the water tank is small, and the length of the pressure rod changes, which causes the water stop pad to be reset quickly to stop the water, and the length of the pressure bar can be adjusted to a suitable one.

2. If the water level of the inlet valve is low, remove the buckle of the inlet valve, rotate the inlet valve body counterclockwise, then adjust the height of the body accordingly, and finally rotate the inlet valve body clockwise. Install the buckle, install the water inlet valve, and connect the filter and water inlet pipe.

3. If there is a lot of dirt at the toilet outlet, you can use baking soda or white vinegar to clean it, which will not hurt the ceramic glaze of the toilet bowl and can be cleaned quickly.

How to solve the problem of slow toilet draining without suction

1. If it is caused by the quality of the toilet itself or the design of the problem, the toilet should be replaced with a high-quality toilet produced by a large brand manufacturer.

2. If the toilet seal is damaged, causing air to enter the toilet, which reduces the pressure in the toilet, the seal should be replaced with a new one.

3. If the bottom of the toilet is not installed properly and there is an offset, resulting in a small part of the toilet drain being blocked, the bottom of the toilet should be reinstalled.

4. If the toilet drain is blocked by foreign objects, you should use a pipe dredging machine, caustic soda, etc. to dredge the blockage.

Tips: There are many original search Zheng reasons that cause the toilet to be slow and there is no suction, the reasons are different, and the grinding solutions will be different.

How to effectively prevent the toilet from draining slowly.

1. In daily life, try not to pour leftovers into the toilet, if you must pour it in, then the leftovers should be flushed with more water, and the inside must not contain hard objects such as bones, in addition, you can not throw hair, sanitary napkins and other insoluble items into the toilet, if these things are thrown into the toilet, it will inevitably cause the toilet to be blocked, causing the toilet to drain slowly.

2. In order to effectively prevent the problem of slow draining of the toilet, it is recommended that when you buy a toilet, you must try to choose a toilet with a large drain outlet and pipe. Because the toilet drain is slow because the sewer pipe is blocked, if you want to discharge the dirt quickly, it is best to choose the toilet with a large drain outlet and pipe, the sewage discharge effect and speed of this toilet will be better, and it is not easy to block.

What should I do if the toilet drains slowly and there is no suction? The toilet drains slowly and has no suction, which is generally caused by the aging of the water seal, broken or clogged pipes. So how should we solve it? Let's take a look.

1. First of all, we need to check whether there is a problem with the inlet pipe of the toilet. If it is found that it is a problem with the water inlet pipe, it needs to be replaced in time, otherwise it will easily lead to leakage of the toilet, and in serious cases, it may also lead to the rupture of the toilet. In addition, it is also necessary to check whether there is a foreign object blocking the lower drain pipe, and if there is a foreign object blocking the water outlet, it will also affect the normal drainage.

Therefore, it is recommended that all friends must pay attention to keeping the bathroom clean. Avoid the accumulation of clutter to avoid unnecessary trouble.

2. Secondly, we can open the sewage outlet and observe whether there is a large amount of yellow water in the stool, if there is, it means that the pipeline has a leakage of the stove and needs to be repaired in time, otherwise it will cause greater problems. If not, it may be due to insufficient water pressure, resulting in unclean flushing, at this time, we can increase the amount of flushing appropriately. If you still can't solve the problem, you need to contact the property and ask a professional master to come to repair it.

3. Finally, we can also use a plug to insert the plug into the drain hole, and then press hard, so that it can play a sealing role. However, it should be noted that it is important to choose the right size and model, otherwise it is easy to cause the plug to be broken. At the same time, it is also important to pay attention to never pierce with sharp objects, otherwise, it is easy to cause water leakage and even lead to the rupture of water pipes.

1. If the sealing ring of the toilet is aging, the sealing function is not particularly good, once there is a leakage, there must be no suction, go directly to the building materials market to replace a new one, to do a good job of sealing, you can use glass glue to hit the edge of the floor drain, as long as the sealing work is in place, there is no problem with suction.

2. If the pipes at home have been used for a long time, especially some old houses, you have to buy descalers, some people are tyrants, like to use Coke, but it is more wasteful, it is better to buy detergents directly in the supermarket, the effect of dredging agent is very ideal, can effectively remove the dirt on the inner wall of the pipe, and then you flush it, you will find that the water flow is relatively large, and the suction power is relatively sufficient.

3. If the water in the siphon toilet is not full, we must check whether there is a water leakage, and check it one by one to solve the leakage such as the collapse.

How to adjust the amount of toilet flushing?

Open the upper lid of the toilet, there are two buttons on the lid of the water tank, one is a small amount of water, the other is a large amount of water, the leaky tank of the toilet is generally a general rule is less on the top and more on the bottom, if you want the full drainage and semi-drainage of the water output is the largest, just adjust the two buttons to the bottom.

The full drain should be adjusted to the bottom, because the full drain is generally used for stool, and the larger the amount of water, the better. Semi-draining is used for urinating, and generally does not need to use a large amount of water, so it is appropriate to adjust it to the middle position.