How to solve the problem of slow toilet draining without suction

The toilet drains slowly and there is no suction, and the solution is as follows

1. It may be caused by the low water level of the toilet, we can take off the toilet tank cover, take out the inlet valve, rotate the inlet valve to the right to adjust the height, and then install it back.

2. The damage of the toilet seal will reduce the pressure, which will lead to insufficient suction power of the toilet, and the flushing will naturally be weak. We can remove the sealant at the bottom of the toilet, lift the base of the toilet to replace the seal, and then reseal the toilet.

3. The toilet is not installed properly, resulting in a part of the drain being blocked, which will also cause such a problem. You can remove the sealant at the bottom of the toilet, reinstall and fix the toilet drain with the sewage outlet, and then fix the toilet base with glass glue.

4. Damage to the toilet tank accessories will also cause the toilet to flush weakly. You can remove the toilet tank cover, carefully inspect the toilet water parts, and replace the damaged water parts.

Flush toilet drains slowly and has no suction:1. The amount of water in the water tank is small, and the length of the pressure rod changes, which causes the water stop pad to be reset quickly to stop the water, and the length of the pressure bar can be adjusted to a suitable one.

2. If the water level of the inlet valve is low, remove the buckle of the inlet valve, rotate the inlet valve body counterclockwise, then adjust the height of the body accordingly, and finally rotate the inlet valve body clockwise. Install the buckle, install the water inlet valve, and connect the filter and water inlet pipe.

3. If there is a lot of dirt at the toilet outlet, you can use baking soda or white vinegar to clean it, which will not hurt the ceramic glaze of the toilet bowl and can be cleaned quickly.

There are two reasons why the toilet drains slowly and has no suction, because the toilet at home is in these two conditions.

The first is that people put some soup water into the toilet that is not easy to flush, causing the toilet to clog. Nowadays, buildings have been built in many places, and our families also live in buildings, and it is not easy to get used to buildings after getting used to rural houses. Sometimes my mother chooses to pour the leftover soup water into the toilet, there is no problem at the beginning, the toilet can be flushed, but then once, my mother poured the remaining soup into the toilet, and my father, who was not at home for ten thousand years, caught up, and then the toilet appeared to be slow and had no suction.

I had to resign myself to the toilet, what a painful thing, and since then there has never been a phenomenon of pouring soup and water into the toilet at home.

The second is that the toilet has been used for too long, resulting in a small problem with the internal structure of the toilet, so that there is no suction. This is the second situation that arises in our family. The toilet at home has been used for about five or six years, and it can still be used at the beginning, but it will not work after a long time.

In fact, it is really a painful thing for the household toilet to encounter the phenomenon of no suction, and it is quickly solved when the toilet has this omen, and at this time, there is no need to spend a lot of money to reinstall the toilet after solving it. Our family just felt nothing at the beginning, and it has dragged on until now, it is really troublesome, and every time I go to the toilet, I have to change my clothes and go to the public toilet downstairs, especially in winter, which is miserable. Therefore, it is very uncomfortable to solve the problem as soon as possible, strangle all kinds of situations into the cradle, and open the toilet.

What should I do if the toilet drains slowly and there is no suction? Move this little trick to solve it easily!

There should be something clogged inside, so the water is slow and there is no suction.

1. The sealing ring is aging and leaking.

There is a sealing ring at the interface between the toilet bowl and the floor drain, and the aging of the sealing ring will cause no suction. Nowadays, it is common to use siphon flushing, so if there is an air leak here, there will be no suction.

Solution: You can buy a sealing ring in the building materials market to replace it, and then buy a tube of glass glue and apply it to the edge of the toilet bowl and tiles.

2. Pollution on the pipe wall.

Another situation is that the old house has accumulated dirt on the pipe wall for a long time, causing the drainage pipe to become thinner and the suction power is not enough.

Solution: There are many supermarkets that sell toilet descaler, and after removing the dirt on the surface of the pipe wall with descaler, the suction power can be enhanced.

Precautions for toilet use:

When buying toilets and other toilet hardware accessories, don't choose cheap ones. Some manufacturers will cut corners or add their own design issues and then sell them to wholesalers at a low price. Therefore, for something like a toilet that is often used, it is necessary to determine the main brand and choose the big brand products when purchasing.

If defective products are purchased, replacing them is not only a hassle, but also a waste of money and time. The toilet seal is damaged, and the sealing performance is impaired. One thing we should pay attention to in the structure of a toilet is negative pressure. The toilet can suck out "dirty" because of the negative pressure inside.

Pro, that is, 1Pour a decomposing unclog into the toilet bowl and let it dissolve the clogged sewer pipe to unclog the pipe. 2.

Replace the mat at the bottom of the toilet to block the air, and the suction power will naturally be greater if the air does not leak in. 3.The accessories in the toilet tank are misplaced, so the water in the tank does not reach the water level, and the suction power will be small, so it can be installed correctly.

Give a thumbs up for your hard work

What should I do if the toilet drains slowly and there is no suction? Move this little trick to solve it easily!

1.First of all, clean the toilet bowl and drain the water in the sink (with a rag - suck it out again and again, wring it out) so that the hydrochloric acid is not diluted after pouring it.

2.Pour the whole bottle of dilute hydrochloric acid (about 500ml) into the toilet sink, do not dilute with water, the pure descaling effect is good, and the ceramics will not be damaged. At this time, you will find that the acid enters the tank and reacts with the scale, turning up the bubbles, so after adding the acid, you should use a waste rag to plug the groove, so that the bubbles generated by the acid will turn down as much as possible, so that the scale inside the siphon pipeline will be cleaned more cleanly.

At first, there will be some smoke and strong smell, so it is recommended to turn on the exhaust fan.

3.Wait for half an hour, clean the scale, and then flush the water, and the toilet drain is smooth and powerful.

How to solve the problem of slow toilet draining without suction

1. If it is caused by the quality of the toilet itself or the design of the problem, the toilet should be replaced with a high-quality toilet produced by a large brand manufacturer.

2. If the toilet seal is damaged, causing air to enter the toilet, which reduces the pressure in the toilet, the seal should be replaced with a new one.

3. If the bottom of the toilet is not installed properly and there is an offset, resulting in a small part of the toilet drain being blocked, the bottom of the toilet should be reinstalled.

4. If the toilet drain is blocked by foreign objects, you should use a pipe dredging machine, caustic soda, etc. to dredge the blockage.

Tips: There are many original search Zheng reasons that cause the toilet to be slow and there is no suction, the reasons are different, and the grinding solutions will be different.

How to effectively prevent the toilet from draining slowly.

1. In daily life, try not to pour leftovers into the toilet, if you must pour it in, then the leftovers should be flushed with more water, and the inside must not contain hard objects such as bones, in addition, you can not throw hair, sanitary napkins and other insoluble items into the toilet, if these things are thrown into the toilet, it will inevitably cause the toilet to be blocked, causing the toilet to drain slowly.

2. In order to effectively prevent the problem of slow draining of the toilet, it is recommended that when you buy a toilet, you must try to choose a toilet with a large drain outlet and pipe. Because the toilet drain is slow because the sewer pipe is blocked, if you want to discharge the dirt quickly, it is best to choose the toilet with a large drain outlet and pipe, the sewage discharge effect and speed of this toilet will be better, and it is not easy to block.

1. If the sealing ring of the toilet is aging, the sealing function is not particularly good, once there is a leakage, there must be no suction, go directly to the building materials market to replace a new one, to do a good job of sealing, you can use glass glue to hit the edge of the floor drain, as long as the sealing work is in place, there is no problem with suction.

2. If the pipes at home have been used for a long time, especially some old houses, you have to buy descalers, some people are tyrants, like to use Coke, but it is more wasteful, it is better to buy detergents directly in the supermarket, the effect of dredging agent is very ideal, can effectively remove the dirt on the inner wall of the pipe, and then you flush it, you will find that the water flow is relatively large, and the suction power is relatively sufficient.

3. If the water in the siphon toilet is not full, we must check whether there is a water leakage, and check it one by one to solve the leakage such as the collapse.

How to adjust the amount of toilet flushing?

Open the upper lid of the toilet, there are two buttons on the lid of the water tank, one is a small amount of water, the other is a large amount of water, the leaky tank of the toilet is generally a general rule is less on the top and more on the bottom, if you want the full drainage and semi-drainage of the water output is the largest, just adjust the two buttons to the bottom.

The full drain should be adjusted to the bottom, because the full drain is generally used for stool, and the larger the amount of water, the better. Semi-draining is used for urinating, and generally does not need to use a large amount of water, so it is appropriate to adjust it to the middle position.

What should I do if the toilet drains slowly and there is no suction? The toilet drains slowly and has no suction, which is generally caused by the aging of the water seal, broken or clogged pipes. So how should we solve it? Let's take a look.

1. First of all, we need to check whether there is a problem with the inlet pipe of the toilet. If it is found that it is a problem with the water inlet pipe, it needs to be replaced in time, otherwise it will easily lead to leakage of the toilet, and in serious cases, it may also lead to the rupture of the toilet. In addition, it is also necessary to check whether there is a foreign object blocking the lower drain pipe, and if there is a foreign object blocking the water outlet, it will also affect the normal drainage.

Therefore, it is recommended that all friends must pay attention to keeping the bathroom clean. Avoid the accumulation of clutter to avoid unnecessary trouble.

2. Secondly, we can open the sewage outlet and observe whether there is a large amount of yellow water in the stool, if there is, it means that the pipeline has a leakage of the stove and needs to be repaired in time, otherwise it will cause greater problems. If not, it may be due to insufficient water pressure, resulting in unclean flushing, at this time, we can increase the amount of flushing appropriately. If you still can't solve the problem, you need to contact the property and ask a professional master to come to repair it.

3. Finally, we can also use a plug to insert the plug into the drain hole, and then press hard, so that it can play a sealing role. However, it should be noted that it is important to choose the right size and model, otherwise it is easy to cause the plug to be broken. At the same time, it is also important to pay attention to never pierce with sharp objects, otherwise, it is easy to cause water leakage and even lead to the rupture of water pipes.