How to install the water tank, how to install the toilet water tank

The water tank is the main part of the cooling system and maintains the heat of the engine by circulating the coolant through the engine waterways. In winter, the air conditioner also transfers heat from the water tank to the car.

In the past, domestic large cars and tractors generally used water, and the water was easy to freeze, so in the northern winter, it was common to see drivers using fire and hot water to bake the engine in the morning. It is also easy to boil in summer.

However, today's cars are relatively delicate, and if you use water, it will corrode the sensors, engine waterways, and water pipes in the tank. Professional coolants contain chemicals such as alcohols, which reduce the freezing point of the solution and increase the boiling point, making it suitable for use in many areas. However, there are also classifications of coolants, and the coolants used in different regions are also different.

Nowadays, cars use special coolant, and pure water can be used in a short period of emergency, but you have to immediately go to a professional car repair shop to repair the cooling system failure, and then clean the cooling system, and then add new coolant. The coolant can be replaced with a two-year or 20,000 km interval. Hope.

If it is a stainless steel water tank, I recommend that you find a professional manufacturer to install it

The installation of the general manufacturer staff is.

1. First, the stainless steel plate is molded into a one-meter square plate for assembly, 2. The bottom plate is spread out on the flat ground and connected by argon arc welding.

3. Assemble the side plate again, and then connect it with the bottom plate for welding.

4. The inner tension ribs of the water tank should be both transverse and longitudinal, and should not be too thin, so as not to deform the water tank due to excessive pressure.

5. Regarding the roof, after the roof is spliced, it is placed on the top of the water tank, and the connection can be welded with argon arc welding in the water tank!

1. First, use a tape measure to measure the size and wall-mounted height of the old water tank at home, and then buy the same or the same water as the original water tank.

2. After purchasing a new water tank, please check the accessories first, find the attachment table, and then identify the accessories. As shown in the figure, the right side is the drain pipe, the left side is the water tank body, and the center is the connecting cup and tapered washer.

3. To start the installation, please assemble the drain pipe first, connect the two straight pipes, and then connect the elbow pipes as shown. Install the entire drain in the old pipe location. If you want to leave the old tube intact, you can ignore this step.

4. The left side is the drain valve, and the right side is the water inlet valve. Screw the drain valve and water supply valve into the water supply tank, check if there is no problem, and then lock the top cover of the box. Find the hook, place it on the wall, drill two holes and open the screws. Snap the hook into the back of the tank.

5. Use a hook to hang the water tank on the two screws. Place the conical rubber ring on the connecting cup, put the connecting cup over the drain pipe, and tighten the drain pipe at the bottom of the tank. On the left side is the connecting cup, and on the right is a tapered rubber ring.

6. The installation is basically completed, just connect the hose to the water inlet of the water tank. Once you're done, you can test the water. If there is a water leak, check the installation manual for any installation errors.

Household stainless steel water tank installation method:

1.First of all, the stainless steel water tank with a size of 170*40*54cm must be welded by professionals to ensure that there is no leakage.

2.Secondly, there are four water pipes on the water tank, which are the inlet pipe, the overflow pipe, the outlet pipe and the laxative pipe. The location of the water pipes is set according to the installation position of your water tank, so that it is easy to connect the tap water and floor drain.

Among them, the overflow pipe determines the height of the water stored in the water tank, and the valve cannot be installed; The outlet pipe should not be too close to the bottom of the water tank to avoid the sediment flowing out; The Epsom Hose is the one that discharges sediment and should be installed at the bottom of the tank.

The steps for the installation of the water tank are as follows:

1.Choose the location for installation: The first thing to do is to choose the location where the tank will be installed, usually the roof and the ground.

2.Prepare the foundation: Lay the foundation in the installation position to make sure it can withstand the weight of the tank.

3.Mounting bracket: The bracket is a necessary condition for the stable installation of the water storage tank, and the judgment needs to select the appropriate bracket according to the size of the water storage tank.

4.Installation of pipes: The water storage tank needs to be connected to the water storage pipe to ensure that it is connected to the drainage pipe on the roof.

5.Install the water tank: After installing the bracket and pipes, install the water tank to the bracket.

6.Installation Accessories: The water tank also needs some accessories, such as water pumps, floats, filters, etc.

7.Test run: After completing the above steps, perform a test run to confirm whether there is any leakage at the connection between the storage tank and the pipe.

It should be noted that when installing the water storage tank, it is necessary to comply with the relevant safety operation section specifications to ensure their own safety and the normal use of the equipment.

Summary. 2. Grounding: Knock the steel expansion bolt into the grounding hole, insert the expansion spiral into the bottom corner of the toilet, tighten the nut to fix, the toilet drain and the ground preset drain pipe should be tightly connected, and then take sealing measures. 3. Install the water tank (1) First, according to the installation height of the water tank and the position of the hole on the back wall of the water tank, punch the hole in the corresponding position on the wall, and hit the steel expansion bolt with a hammer.

2) Place the tank according to the prompts, insert the expansion bolt into the wall hole, add a 3mm thick nylon washer, and then tighten the nut. (3) When installing the connecting pipe between the water tank and the toilet base, you need a copper pipe or plastic pipe, don't ignore this problem, the connecting pipe between the inlet pipe and the bottom of the water tank is a stainless steel corrugated pipe.

Hello, Jane Bang for your question is; The answer is the See's Simplified Frequency Tutorial.

1. Preparation (1) First check the model and quality of the toilet, confirm that there is no problem, manually select the number of parts and prepare the installation kit. (2) Conduct the actual inspection, plan the installation location, decide on the implementation plan, measure the required dimensions and make arrangements. (3) After aligning the ground drainage nozzle and the drain at the bottom of the toilet, draw the position of the bottom corner of the toilet, fix the hole on the ground, and drill the hole to a depth of about 5 cm with an impact percussion drill.

2. Grounding: Knock the steel expansion bolt into the grounding hole, insert the expansion spiral into the bottom corner of the horse fuel bucket, tighten the nut to fix, and the toilet drain and the ground preset drain pipe should be tightly connected, and then take sealing measures. 3. Install the water tank (1) First of all, according to the installation height of the water tank and the position of the hole on the back wall of the water tank, punch the hole in the corresponding position on the wall, and hit the expansion bolt of Pi Yunxiang steel with a hammer. (2) Place the water tank quietly according to the prompts, insert the expansion bolt into the wall hole, add a 3 mm thick nylon washer, and then screw on the nut and tighten.

(3) When installing the connecting pipe between the water tank and the toilet base, you need a copper pipe or plastic pipe, don't ignore this problem, the connecting pipe between the inlet pipe and the bottom of the water tank is a stainless steel corrugated pipe.