The practice of making your own blackboard wall, how to make your own blackboard

Step 1: Select an area where you need to make a blackboard on the wall, remove the problematic wall skin, and repair the defects on the wall. Lay a good foundation on the surface as much as possible. Then sand it smooth with sandpaper and wipe off the floating ash with a towel.

Step 2: Use a ruler and a pencil to draw the edge of the blackboard on the wall, taking care to ensure that the blackboard is level. In addition, you should prepare an eraser to erase the wrong place at any time.

Step 3: Attach masking strips along the border you drew with a pencil. (If you want the blackboard to be curved, you can DIY a wax paper template by yourself).

Step 4: Brush the finished frame with chalkboard primer. Dry fully according to the time specified in the paint instructions.

Step 5: Carefully sand with fine sandpaper and wipe clean with a soft, dry towel.

Step 6: Brush the blackboard finish in the same direction to ensure a drying time of more than 12 hours.

Step 7: Carefully sand with fine sandpaper again, then wipe clean with a soft, dry towel.

Step 8: Brush the blackboard topcoat for the second time from the opposite direction, pay attention to keep the strokes smooth and even, and dry for 24 hours after brushing.

Step 9: In order to get the best writing feel, you also need to work on the entire surface of the chalkboard. The easiest way to do this is to roll back and forth on the surface of the chalkboard with the sides of the chalk.

Then wipe off the chalk ash with a chalkboard. Wipe it again with a soft, slightly damp cloth, and finally, remove the masking paper or stencil from the wall.

Tools Raw materials.

A clean wall is needed with chalkboard paint, brushes, masking tape, sandpaper, soft towels.

Method steps.

1 6 Step by Step Reading.

We need to choose the wall to be used as a blackboard, and after determining the area, if there is a problem with the wall skin, we need to shovel it off, and then repair and smooth the wall, polish it with sandpaper, and wipe off the floating ash. The foundation must be laid!

Draw the outline line of the chalkboard and apply masking tape along the outline line.

Brush the blackboard paint in the painted frame, the general blackboard paint has two kinds of oil-based blackboard paint and water-based blackboard paint, when brushing as a general paint with a roller brush, can only be brushed vertically or horizontally, and the brush is even. There will be instructions on the chalkboard paint, and wait for it to dry sufficiently according to the instructions above.

First sand it with fine sandpaper to smooth it and then wipe it clean with a paper towel. Then brush the chalkboard paint in the same direction, and the drying time is more than 12 hours.

It is a repeat of the previous step, but the re-brushing is in the opposite direction to the previous one, and there is no pause in the middle of the brush. The drying time after brushing is also one day.

Finish the blackboard wall by making sure that the writing is smooth, and then remove the masking tape from the wall to complete the chalkboard wall.

Precautions. It is recommended to clean the blackboard surface with a soft cloth, do not cause scratches, scratches will affect the effect, and the wipe will not be clean.

You can regularly wipe it with a wiping cloth that has been wrung out after wetting, and it can be cleaned.

How to make a pro on the blackboard! Hello, happy to answer your <>

The pro-blackboard can be made with the following materials and methods: 1. The material used in the old-fashioned blackboard is wood, which is obtained by brushing black paint on the wood. 2. Hard objects such as cement can also be used to make blackboards, which can be made by coating black paint on the surface of cement.

3. Glass blackboard, as the name suggests, uses glass, which is brushed with dark green paint on the back of the glass. 4. At present, a kind of blackboard that is widely used is made of rubber and made of mechanical assembly line, and the process is synchronous for cladding and cutting, and then framing, quality inspection and storage. 5. Color-coated steel plate is made of high-quality alloy steel plate coated with wear-resistant coating.

6. The new material composite panel is made of imported polymer alloy particles and epoxy resin after one-time pressing and molding, and the surface is not treated at any time. 7. Magnetic blackboard, lining the inside of the blackboard with magnetic stripe magnetic rods, or attaching magnetic particles on the surface. When using, you can use magnetic nails, magnetic blocks, etc. to fix small teaching tools or ** for easy display.

1.Choose an area where you need to make a blackboard on the wall, remove the problematic wall skin, and repair the defects on the wall. Lay a good foundation on the surface as much as possible, then sand it with sandpaper and wipe off the floating ash with a towel.

2.Use a ruler and a pencil to draw the edge of the blackboard on the wall, taking care to keep the blackboard level. In addition, you should prepare an eraser to erase the wrong place at any time.

3.Attach masking paper tape along the border of the painting. (If you want the blackboard to be curved, you can DIY a wax paper template by yourself) 4

Paint the finished frame with a chalkboard primer. Dry fully according to the time specified in the paint instructions. 5.

Carefully sand with fine sandpaper and wipe clean with a soft, dry towel. 6.Brush the chalkboard topcoat in the same direction to ensure a drying time of more than 12 hours.

7.Carefully sand again with fine sandpaper and wipe clean with a soft, dry towel. 8.

Brush the blackboard topcoat a second time in the opposite direction, pay attention to keep the strokes smooth and even, and dry for 24 hours after brushing. 9.In order to get the best writing feel, the entire surface of the chalkboard also needs to be treated.

The easiest way to do this is to roll the side of the chalk back and forth on the surface of the chalkboard, then wipe the chalk dust off with a chalkboard eraser, wipe it again with a soft, slightly damp cloth, and finally remove the masking paper or stencil from the wall. 10.Don't forget to tell your child that it's okay to scribble on the board, but not anywhere else.

I hope my can-do can help you <>

Do you have any other questions?

Preparation: or spike black paint, cardboard, sponge, ice cream sticks.

2. Then use black pigment to paint the cardboard to make the hole black, as shown in the figure below.

3. Then use the ice cream stick to make the frame of the blackboard, as shown in the figure below.

4. Next, use a sponge to make a blackboard eraser, as shown in the figure of Natuanfeng.

5. Finally, the homemade blackboard is completed, as shown in the figure below.

Steps to make your own chalkboard:

1. First of all, look around the home from all angles and directions, choose a wall to be used as a blackboard wall, shovel off the problem wall skin to repair the defects, and then polish it with sandpaper as shown in the picture and wipe off the floating ash;

2. Then use a level ruler and a pencil to draw the edge of the outer frame, pay attention to ensure that it is horizontal and vertical, ensure the flatness of the wall, and then paste the masking tape along the outer frame line;

3. Brush the blackboard paint in the outer frame, choose the water-based blackboard paint, and let it dry fully according to the specified time (12 hours) according to the paint instructions; Brush vertically or horizontally, try to ensure that one direction is brushed evenly;

After brushing it once, carefully polish the fine sandpaper and smooth it, and wipe it clean with a soft towel; Paint the blackboard topcoat for the second time in the opposite direction, and brush it evenly and meticulously, drying wide and hungry for about 24 hours;

4. Finally, use the chalk side to roll back and forth on the finished surface of the paint, and then wipe it with a moist soft cloth, never wipe it directly with a dry cloth, it is easy to leave scratches, and the wet soft cloth can ensure the best texture of writing after wiping.

The blackboard wall is mostly dark in color, which is easy to match the overall decoration style of the home. It is recommended that after delineating the area, paste a piece of colored paper in the same color as the blackboard paint. Brush black on black paper, simulate the color is satisfied before starting to brush.

People who have a little baby in the house will make a blackboard in their own home, so how to make the wall into a blackboard? This is a problem.

How to make a wall into a chalkboard Before making it, you need to use a shovel to repair the problematic wall and fix the wall defects, please choose the part of the wall that should have a wall. Lay the foundation on the surface as much as possible, soften it with sandpaper, and then wipe off the dust with a towel.

How to make a wall into a blackboard Use a ruler and pencil to draw the outline and border of the blackboard on the wall, paying attention to the height of the blackboard. Also, prepare an eraser and wipe the wrong place at any time. Textured tape is then applied along the boundaries of the painting.

You can also eat the wax paper template bending board directly and wipe the chalkboard primer on the frame. Completely dry according to the time specified in the paint instructions.

How to make a blackboard on a wall Carefully rub the sand with fine sandpaper and then wipe it with a soft, dry towel. Then wipe the topcoat in the same direction, making sure the drying time is at least 12 hours. Carefully sandwich the sample in the middle with good sandpaper and wipe it with a soft, dry towel.

How to make a wall into a blackboard, we must pay attention to brushing the blackboard a second time in the opposite direction and keep the strokes smooth and even. Brush and dry for 24 hours.

How to make a wall into a chalkboardIn order to get the best handwriting feel, you need to cover the entire surface of the chalkboard. The easiest way to do this is to use the side of the chalk to roll back and forth from the surface of the chalkboard, then wipe the chalk dust with the chalkboard, wipe it with a soft, damp cloth, and finally remove the ** or stencil from the wall. But don't forget to tell your child that you can draw on the board like crazy.

However, we can't graffiti anywhere else.

Focus on the environment. Because the interior wall occupies a large amount of internal space, many decorative materials are used, especially the environmental protection of interior decoration materials, especially the environmental protection of the elderly and children's families. Material selection.

Typical wall decoration materials include paint decoration materials, veneer materials, gypsum materials, etc. Paint wall materials are often used for home decoration, but the wall is a lot of harmful substances. When manufacturing materials, it must be clear that the environmental indicators of the materials must comply with the relevant terms.

Focus on construction technology. Care must be taken during the construction process, as the wires must be pierced to perform the embedded work. When adding or modifying water pipes, the grooves of the wall cannot be thrown horizontally, it is important to pay attention to the size silver size at this point, because it cannot exceed 3-5 cm, if the groove is deepened, it may touch the rebar of the wall, and due to the sawing of the rebar may greatly reduce the safety of the wall.

No matter what kind of wall decoration method, in fact, as long as it is careful and careful, it will have a good effect.

You can get it for free

1: Two people should cooperate together, and prepare a scratch card or bank card by yourself.

2: Tear off half of the stickers on the back of the blackboard, don't tear all of them.

3: Fix it on the wall, first use a scraper to scrape the top sticker of the blackboard paste, remove air bubbles, and stick it firmly. When scraping, pay attention to scraping from the middle to both sides, so as to remove the air bubbles.

4: Then gradually scrape from top to bottom, while scraping, another person pays attention to cooperation, while tearing off the sticker at the back.

5: After pasting the blackboard sticker, observe whether the whole blackboard sticker is uneven, small bubbles, if there is, and then use a scraper to remove the bubbles.

Linxi 7th Road North End South of Long-distance Bus Station.

The Commodity City Educational Supplies District sells a lot.

It's better to use blackboard paint than to use blackboard paste!!

I also made one at home.,It's that kind of wall sticker.。。 ** on a lot. The back is a special glue, back to the wall is not much harm, while.

Answer**There is a diagram on it, you can understand it at a glance, generally the wall is wiped with a cloth to remove the dust on the surface, and then the blackboard wall sticker is pasted on, and the transparent paper behind the wall sticker is pulled down little by little, and the wall sticker is smoothed with a towel. Pay attention when posting, the problem is not very big.