What kind of board should be laid in a damp place?

Where there is moisture, it is better to lay floor tiles.

Well, wooden floors can lose their shape in a damp environment. Common floor tiles are: vitrified tiles.

Polished tiles, matt tiles.

Glazed tiles, printed bricks, non-slip tiles, special acid-proof floor tiles. Buying floor tiles should be chosen like this:

First, to check whether the color of the tile is pure. This trick is very simple, mainly to observe whether the color of the back of the tile is uniform and consistent. Good quality ceramic tiles, green body color system.

1. Symmetry. Second, it is necessary to observe whether the particles of the cross-section of the tile are delicate. Consumers should note that the cross-section here does not refer to the cutting surface around the tile, but to the tile fragments.

of the fracture. Generally speaking, the fracture is fine, hard and brittle, and the color is the same. Because the fine particles of ceramic tiles have strong waterproof ability; The ceramic tiles with larger particles are easy to soak in moisture and affect the quality.

Third, pay attention to the thickness of the glaze layer. The ceramic tile glaze is what we call the entire surface of the tile, and the glaze thickness is the thickness of the glaze cross-section. The glaze is the most expensive material in the construction of ceramic tiles, and the thicker the glaze layer, the better the natural quality.

Fourth, listen. Tap on the tiles and listen for a crisp sound. If the sound is clear and pleasant, it is the top grade, and if the voice is dull, it is the inferior product.

Fifth, test the waters. Consumers can pour some water on the back of the tile and pay attention to how quickly the tile absorbs water. After a few minutes, see if the marks left by the water on the front are obvious.

The density of tiles that infiltrate slowly after the water disperses is large, and the marks left by the water are not obvious, so they are regarded as the top grade. 6. Take two bricks back to back and face to face to see if they can be closely contacted, and there is no gap, and whether there is a phenomenon of excessive gap, you can judge whether there is warping. Seventh, find ink on the surface after an hour of scrubbing to see if there are traces, no traces are good bricks, there is no infiltration of the resolute do not choose.

8. Take two bricks to measure the geometric dimensions of the two bricks, the length and width and the diagonal to see the size deviation of the bricks, there is no deviation from the grade 9. You can refer to the test report issued by the national or industry testing agency provided by the merchant to compare the following index data: water absorption, wear resistance, acid resistance and pollution index identification and comparison.

Where there is moisture, I personally think that it is better to use the floor tiles directly, and if the floor is laid, it is generally made of bamboo or wood, which is easy to mold.

Wet areas are covered with PVC plastic flooring, which is made of polyethylene as a raw material. Safe, environmentally friendly, non-toxic, formaldehyde-free, fireproof, waterproof, non-slip, water-free, wear-resistant. Perfect for home décor.

Floor tiles, do a good job of overall waterproofing first, and do some waterproof work on the ground and walls before laying.

Now the better laminate flooring is basically very small by moisture deformation, if it is a solid wood floor, it will have a great impact.

However, no matter how good the laminate flooring is, it will also be affected by moisture, after all, thermal expansion and cold contraction are the law.

As long as the floor tiles are protected for a few days after paving, the humid air will not affect the floor tiles.

Moisture may cause gaps in the floor, and the ash on the ground will come out of the gaps because of stepping on the floor.

The second way is to use tiles to pave, waterproof tiles will not be affected by moisture, generally used in the bathroom!

If it is not the first floor, there is no need to do the ground moisture-proof treatment.

The floor has a wax seal. The damp effect is okay, but the quality is average.

Personally, it is advisable to lay tiles.

I do interior decoration by the sea. Personal experience. Thank you.

It is recommended that you lay tiles, no matter what kind of floor will absorb moisture, once it absorbs moisture, it will be deformed.

You can start with a layer of moisture-proof floor mats. Or find a layer of cement mortar, then lay a layer of waterproof membrane, and then find a layer of plain cement to laminate again, the effect is good. I just renovated a basement and it was with this construction method that it worked well.

Since it is a keel, the floor is not directly attached to the ground, in that case, there will be no big problem. As long as the ground is not very wet (that is, the kind that can see water stains on the ground on a rainy day), you can use the wooden floor. The key is to find a few inconspicuous places around the room, such as the back of the TV cabinet against the wall, the corner of the wall under the floor-to-ceiling curtains, etc., and make a few ventilation holes (that is, drill a hole in the floor).

No, the underside of the laminate floor is a cushion and is made of styrofoam. Function: cushion the force on the floor and protect the bottom layer of the floor; a certain thermal insulation effect; Isolate the base layer and the floor, so that the laying is even, and there will be no uneven feeling when used.

It's best to wait for the ground to dry a little longer.

No, it will peel after it is laid.

1. There are 5 basic requirements for the laying of all PVC floors: 1. The foundation is firm, 2. The flatness is good, 3. The foundation humidity is small (less than, 4. The ambient temperature meets the requirements (greater than 15 degrees), 5. The foundation is clean and pollution-free.

The floor is wet and cannot be laid on the PVC floor, because the PVC floor construction is mostly bonded with water-based glue, the ground is wet and the glue cannot be dried, and the adhesive force of the glue cannot meet the bonding requirements, and there will be many quality problems such as blistering, so the ground humidity must be less than. Even if you use two-component glue, there will be mildew on the PVC floor due to the dampness of the floor, which will cause the PVC floor to discolor.

It can also be adsorbed with activated carbon, and it can also purify the air ,..

Plastic sheets can play a role in protecting against moisture, because they directly block the moisture from contact with the floor, and at the same time prevent the moisture from reversing upward. Therefore, laying a layer of plastic plate can effectively prevent moisture.

Not only is it not moisture-proof, but it can also damage the floor tiles. So don't use this way to protect against moisture, you can put a dryer indoors.

It is not suitable to lay plastic panels on top of the floor tiles when the first floor is wet, it is better to lay a layer of cement or tiles, so that it can effectively prevent moisture.

Yes, it can have a very good moisture-proof effect, and it is still more recommended.

OK.

Many people feel that laying wooden floors in damp places will easily damage the floor, so they choose to lay tiles. In fact, the tile is not easy to absorb the moisture of the outside world, and the moisture in the air will adhere to the surface of the tile, so the floor is easy to slip, which is not a small harm to the elderly and children. There are benefits to laying wooden floors in a damp environment.

When laying wooden floors, moisture-proof mats are often placed at the bottom to effectively isolate moisture from the surface. And the characteristics of the wood floor itself can absorb the moisture in the air, so that the moisture in the wood floor and the moisture in the outside world are balanced, and moisture will not be formed on the surface, and it is not easy for people to slip on it. It should be noted that when laying wooden floors, it is necessary to leave enough gaps, because wooden floors will expand after absorbing water, and leave enough buffer space.

Therefore, in a humid environment, you can choose to lay wooden floors.

Wood board installation and maintenance matters:

1. After the wooden floor is paved, it is necessary to wait at least 24 hours before use, otherwise it will affect the use of the solid wood floor. Generally, solid wood flooring has poor water resistance, and should not be wiped with a damp cloth or water to avoid tarnishing. Usually after experiencing the test of temperature difference in the four seasons, the wood floor will become more and more stable, and paying attention to daily maintenance can prolong the service life and improve the use effect.

2. After paving the wooden floor, do not move in temporarily, be sure to keep the indoor room ventilated, or often open the air conditioning device to adjust the indoor temperature and humidity, otherwise the risk of cracking or deformation of the solid wood floor may be caused by the change of indoor temperature and humidity, and do not cover the floor with plastic sheets, newspapers and other objects for a long time, otherwise it will affect the gloss of the paint surface.

3. Wooden flooring should also be noted to avoid long-term exposure to sunlight or sharp rise and fall of temperature and humidity in the room, which may affect the service life of wood flooring.

4. Pay attention to keep the wooden floor dry and clean, and avoid moisture, rain and flooding of the wooden floor; If there are stains on the surface of the floor, or there are dirt at the joints of the floor, it is recommended to clean it with special cleaning products for solid wood floors with vacuum cleaners, etc., and it is not appropriate to clean with objects with water, do not mop the floor with a wet mop, and do not use alkaline water, soapy water, flammable materials or high-temperature items to clean the surface of the floor.

If it is the ground floor, it is better to lay floor tiles. Above the second floor, you can do some moisture-proof treatment on the ground and then lay the floor.

In fact, floor tiles in a humid environment will be more humid because they cannot absorb moisture. On the contrary, wood has a very good effect on the humidity regulation of the environment, and the moisture absorption and dehumidification of wood itself can directly alleviate the change of indoor humidity.

However, the traditional wooden floor uses six-sided sealing paint, which turns the wooden floor into a piece of "plastic", and its humidity regulating effect cannot be played.

So, you can buy the Forest Star Cultural Floor, which is a floor that breathes. After adopting exclusive processes such as unsealed paint on the back panel, the surface of the floor is exposed to air in a larger area, and the air humidity and temperature of the room are adjusted to ensure the balance of indoor moisture and temperature difference, so that the floor can "breathe" freely.

It's better to deal with it before paving! By the way, how is the ventilation in your place?

The whole room is wet? Is it underground? Go buy dry and squeeze these and put them in the closet, but if you live in a basement room, then I recommend that you move early, it is not good for your health to live for a long time.

Ventilation for a long time, or spread a tarp on the ground.

If you turn on the air conditioner, you can dehumidify.