How to adjust the Suzuki Tianyu light, where is the Suzuki Tianyu fog light switch

1. If you adjust it yourself, it is best to adjust it at night, but don't adjust it on the road, not to mention the danger, it is not easy to see the effect, try to choose it in the community or yard.

2. It is best to prepare a flashlight, which is not very clear at night.

Adjustment essentials: 1. Put the front of the car vertically against the wall, about 10 meters away from the wall.

2. Turn on the high beam tone, generally the high beam is suitable, the low beam is also suitable, it is best not to turn on the low beam tone, it is not easy to distinguish whether the high beam is suitable.

3. Cover the temporarily out of tune lamps with a cloth and tune them one by one.

Steps: 1. After turning on the high beam, stand in front of the headlight, keep your feet as close to the headlights as vertically as possible, observe the position of the high beam on your feet, take the center of light (that is, the brightest light from the headlights) as the center point, and write it down.

2. Then go to the wall, move vertically to the wall (don't go crooked), and mark the wall according to the position of the light center on the foot.

3. Use the screws to the scale teeth of the rotating headlight, and be sure to shine the light center on the mark you engrave (the distance between the top and bottom should not exceed 10 cm).

4. If there is no other person in the car when the lights are adjusted, you can adjust the optical center slightly higher (generally not more than 5 cm), the reason is very simple, the empty car should be higher, and the car should sink a little bit.

5. Adjust up and down to find that the center of light moves obviously, if you adjust the left and right, the center of light is not obvious, I turned several times before moving a little, so don't worry if you see that the center of light is not moving left and right, continue to turn the screwdriver hard until the center of light shines on the mark you engraved.

6. After the center of light of the two lights is aligned with the scale, stand in front of the front of the car (slightly away from the car), pay attention to the lamppost emitted by the headlights, and it is easy to see the high beam at night to see if it is vertical forward, because it is possible that you have shifted when you walk to the wall to make a mark.

Supplement: 1. If you don't change the headlights, you generally only need to adjust the height, and the left and right are basically more accurate.

2. Adjust the headlights, please note that the left light (seen from the driver's seat) should be slightly lower than the right light, otherwise it will shine on other cars when driving, which will affect safety.

Put a board in the front of the car, turn on the lights, there will be a gear or hexagon at the back of the lights, turn it will find that the lights are also moving, generally the left side should be adjusted lower than the right side, because to prevent the car from being dazzling.

Summary. That is, there is a button marked with fog lamp near the instrument panel, and after turning on the light, press the front fog lamp to light up the fog lamp in front; Press the rear fog lights to light up the fog lights behind the car;

That is, there is a button marked with fog lights near the dashboard, and after turning on the lights, press the front fog lights, and you can make trouble to light up the fog lights in front of you; Press the rear fog lamp to light up the fog lamp behind the car with a lack of cover;

Hello pro, Suzuki Tianyu 11 roof lights off the method is as follows, first find the switch of the roof light, generally in the case of oak loss, it is in the middle of the front of the main driver's head Oh pro, turn the switch of the roof light in the car to off, the light will go out. You can also set the switch to "door" mode next to the pin, and the light can be turned off when the door opens and closes again. If the switch is in the off position, the light will always be on, and at the same time, there will be a button next to the ceiling lamp in the car, and there are generally three modes on this button, namely on-even-on mode, door opening and closing mode, and off-off mode.

When the button is set to "Door", the light will automatically light up when the door is open and turn off automatically when the door is closed

Summary. Hello dear. The reasons why the turn signal frequency is too fast are:

1. The turn signal bulb wire is burned out; 2. Poor contact between the bulb and the lamp holder; 3. The power of the bulb is too small; 4. Individual turn signal lines are short-circuited. It is recommended to go to the repair shop for inspection, and the specific situation needs to be analyzed and understood. If one of the three bulbs in the turn signal shade on one side does not light up, the resistance value in the relay will increase, which will cause the flickering frequency to increase.

If a bulb does not light up, the resistance value in the relay will be different, and it will flash fast. If the bulb is broken, the current is small, and the frequency will be faster.

Hello dear. The reasons for the rapid frequency of turn signals are: 1. The turn signal bulb wire is burned out; 2. Poor contact between the bulb and the lamp holder; 3. The power of the bulb is too small; 4. Individual turn signal lines are short-circuited.

It is recommended to go to the repair shop for inspection, and the specific situation needs to be analyzed and understood. If one of the three bulbs in the turn signal shade on one side does not light up, the resistance value in the relay will increase, which will cause the flashing frequency to increase. If a light bulb does not light up, the resistance value in the relay will not be the same, and it will flash quickly.

If the bulb is broken, the current is small, and the frequency will be faster.

Hello dear, if it's convenient, give me a 5-star thumbs up with a fortune hand, thank you.

There is a lever on the lower left side of the steering wheel, and the handle of the joystick can be turned on by turning on the night lights and low beams. Push forward and down to turn on the high beams and pull back to turn them off.

Here's the one:

Precautions] Generally, it is best not to drive high beams when driving in the city, because the lighting conditions in the city are generally better. If the angle of the high beam is too high, it is easy to shake the eyes of oncoming cars and surrounding pedestrians, affecting the vision of others, which is very unsafe and is an impolite driving behavior.

However, at night, the high beam can be turned on and off alternately to warn pedestrians and vehicles around the horn to avoid causing too much noise.

When driving on highways and in places where there are no street lights in the suburbs, you can turn on the high beam to expand the field of vision. However, when there is a car on the opposite side and you need to meet the car, for the sake of safety and courtesy, switch to low beam.

Tips] If there is a vehicle in the opposite direction and the high beam is not turned off, it is an illegal act, and the traffic police can fine and deduct points.

Toggle the light control button forward, it is explained in the manual.

Summary. Hello, I am very happy to answer this question for you, the headlight adjustment of the Suzuki Tianyu SX4 model is a knob on the left-hand side of the steering wheel.

Tianyu Suzuki SX4 headlights adjust the tune up and down, that tune left and right, and the knob is in**.

Hello, I am very happy to answer this question for you, the headlight adjustment of the Suzuki Tianyu SX4 model is a knob on the left-hand side of the steering wheel.