What should I do if the toilet tank is not watering? What is the solution to the toilet tank not wat

The solution to the toilet tank not watering is as follows:1. Close the angle valve first, remove the angle valve with a tool, and check whether the angle valve is rusty or scaled.

2. After the angle valve is disassembled, replace it with a new angle valve, and there is a filter screen under the toilet tank, remove the filter screen, and then rinse it with clean water.

When buying a flush toilet, you should pay attention to the appearance gloss of the flush toilet, generally the higher the gloss, the better the quality, and the longer the service life.

As we all know, the toilet will be used for a long time, there will be problems such as water leakage and non-water, which brings great distress to our lives, so what should we do if the toilet tank is not watered? Let's take a detailed look at the two repair methods for toilet tanks not watering, I hope we can give you some help and inspiration.

What to do if the toilet tank doesn't go to water:

1. What should I do if the toilet tank does not --- water

1. First of all, it may be that the filter screen in the toilet water filler is blocked by scale, resulting in the tap water not coming in, so as long as the stains in the filter are cleaned during maintenance, but during operation, the valve should be closed, and then the toilet should be flushed to discharge the water in the water tank.

2. Secondly, to check whether there is a hexagonal nut under the toilet, it is connected to the water replenisher of the water tank, rotate the nut with a wrench, and then look up along the position of the nut, there is a same nut, unscrew it, so that the water replenisher can be taken out.

3. Finally, after the water filler is removed, see if there is a small square column in the middle of the tube, pull it out with needle-nose pliers, you can see whether the square column and the filter are connected together, and then take it out and clean the filter with a toothbrush and then install it back as it is.

2. What to do if the toilet tank does not --- water

1. Before maintenance, the water valve should be closed, so as not to be sprayed with water during operation, and then the lid of the water tank can be removed, you can see the accessories inside, the accessories are mainly divided into 3 parts, the first is the drain valve, just below the cover button, the second is the water inlet valve, next to the drain valve, and the third is the position of the button.

2. After turning the toilet lid up, see if it will touch the water inlet valve, if it will, you should adjust the position of the water inlet valve, and then see if the floating bucket and float of the water inlet valve are active, if it is not moving, the water can not enter the height, therefore, to adjust the position of some floating buckets and floats, so that the problem of the toilet tank not being watered will be solved, 3. If the above two methods cannot solve the problem, it is best to contact professionals to check the maintenance of Sui Yuji, do not move at will, In order not to cause more damage and bring more trouble to the repair, so that the guess outweighs the loss.

1. First of all, check whether the valve (angle valve) switch of the tap water at home is open.

2. If it is open, then check the flush switch: first check whether the flush switch has elasticity and whether it rebounds when pressed, if not, it means that the spring inside the button is rusty, at this time you can replace the button, or if you are not too troublesome, it is okay to press it several times each time you use it to reset.

3. If the water pressure is too low, it is difficult to get into the water. The low water pressure may be caused by the high floor of the house or the overall water pressure of the community, or it may be caused by the water pressure being too low due to the water valve being opened too small.

4. Open the water tank cover to check whether the triangle valve is blocked, if the triangle valve is blocked, the toilet can not be watered, you can disassemble the triangle valve to see if the connection with the inner wire is blocked, and see whether the valve core is open and closed normally.

5. After the toilet is used, the toilet does not have water, which is generally a blockage problem, at this time, you can use some waste toothbrushes and other tools to clean the water parts and filters, of course, with limescale cleaners, the cleaning effect will be better. You can also add some scale remover to the water filler to remove the scale, which is less likely to clog.

6. The toilet can be solved by adjusting the height of the pontoon, and the toilet tank cover will be pushed to the inlet valve, and the inlet valve needs to be adjusted until the float or float of the inlet valve moves freely, and the water generally cannot come in if the floating bucket is stuck.