How to carry out the paving of vitrified tiles

Pay attention to the foundation treatment before paving. The most important thing before paving is to do a good job of foundation treatment. It should be treated first to be skin or ground leveling, and the bricks can be paved only after the dry paving base reaches a certain hardness.

When paving, most of the joints are adjusted between 2-3, it is recommended that the anti-pollution vitrified bricks with water wax on the surface are made of porcelain wear-resistant bricks, and micropores that cannot be seen by the naked eye will routinely appear after surface polishing, so it is best to coat a layer of floor wax on each vitrified tile before construction. Before paving, check whether the surface of the vitrified tile is waxed. If not, it must be re-waxed before construction.

The method of judging waxing: see if there is a layer of wax on the brick surface. The brick surface gives the feeling of fog.

If you touch it with your hands, you will have fingerprints.

Try to pave the road before you pave it. After using the same color number and size, mark the number on the bottom of the brick. If the brick surface has a decorative pattern or directional pattern, the product should be paved according to the illustrated method to achieve the best decorative effect.

The paving and tapping tool needs to be wrapped in a white cloth. During the construction process, construction workers are required to wrap in a white cloth before using a rubber hammer. Poor antifouling performance of the brick hammer striking the brick surface will leave black marks.

Pay attention to the protection of the finished product For the newly laid vitrified bricks, the tile packaging box must be covered on the paved bricks, preferably with a rainproof cloth, to prevent sand from damaging the brick surface, as well as decorative paint and glue dripping on the bricks and polluting the brick surface.

As a wall brick, vitrified bricks should pay attention to the following problems: check the wall foundation first to see whether the original wall is suitable for tiling, such as whether the wall is hollow and cracked, whether the wall waterproof brushing treatment is qualified, etc. If there is a problem, it needs to be rectified before tiling.

When fixing floor tiles and laying tiles, when laying vitrified tiles on the wall, it is necessary to determine the level of the tiles, and fix and support the vitrified tiles to prevent the tiles from falling. When paving, the content of cement mortar can be slightly greater than that of ordinary wall tiles, and the cement content can be slightly higher. It can be 1:

2. Glue can be added to the cement mortar to increase the adhesion of the tile.

The back of the vitrified tile should be evenly coated with cement mortar to prevent the tile from hollowing. When paving, it is recommended not to pave one wall at a time. The entire space can be laid out layer by layer.

When laying one wall at a time, the main purpose is to avoid the cement mortar setting time and make the tiles fall. The tiles are laid in a circle, the setting time is more sufficient, and the tiles are easier to fix. When laying tiles, it is necessary to protect the finished products of doors and windows and other related items to prevent damage.

At the same time, clean up the cement mortar extruded from the brick joints in time, and hook the joints after the tiles are dry. After the tile paving is completed, it is necessary to check the quality of the wall paving and whether there is a hollow drum.

First of all, it should be determined whether the glass brick is flat, and then the bottom glass brick should be fixed, which can be bonded with cement mortar, or it can be supported by wooden cylinder air, and then the off-seam paving method is adopted, after all the paving is completed, you can wait for the mortar to dry thoroughly, and during this period, you must not walk on the brick to prevent the drill bit from cracking, uneven or dislocated.

Before paving, should be dealt with well to be skin or ground leveling, dry paving method of the base layer to reach a certain hardness to pave bricks, paving joints between 2-3 adjustment. Before paving, first try to pave on the ground, after using the same color number and size, and then mark the number at the bottom of the brick, if the brick surface has a pattern or directional pattern, the product should be paved according to the method shown in the figure, in order to achieve the best decorative effect.

First sweep the ground, sweep all the gravel on it, spray a little water, then lay cement to make it sticky, and then paste the prepared bricks and then use a small hammer to knock them, so that the gaps will become smaller, just wait for the air to dry.

Summary. Hello dear and happy to answer your <>

The process of vitrified brick floor paving project is increased as follows: 1. Clean the site first, clean the surface layer of the concrete floor, and avoid impurities affecting the strength. 2. Measure the highest level at the construction site, and do not knock off the convex objects on each wall at this point, and the mortar can not be paved with more than 1 to 4 materials to clear the cement and sand The ground is sprinkled with an appropriate amount of water first, and the ground is sprinkled with cement powder before construction.

4. Sweep evenly with a broom to increase the adhesion between the ground layer and the cement mortar.

Vitrified brick floor paving engineering process.

Hello Shenling, happy to answer your <>

The process of vitrified brick floor paving project is increased as follows: 1. Clean the site first, and clean the surface layer of the concrete ground to avoid impurities affecting the strength. 2. Measure the highest level at the construction site, so that the convex objects are not knocked off on each wall, and the mortar can not be paved with more than 1 to 4 materials to clear the cement and sand on the ground, and sprinkle the ground with cement powder before construction.

4. Sweep evenly with a broom to increase the adhesion between the ground layer and the cement mortar.

Hello dear, the following <> for your expansion

Old chain ground vitrified brick paving method: 1. Before paving tiles, it is necessary to keep the flatness and verticality of the base surface within the qualified range, and whether the high chain of the construction hole is blocked. 2. The concrete wall needs to be brushed, and all kinds of wall Qi and Sun noodles need to be moistened with water in advance, and then the wall surface should be cleaned to keep the wall clean and tidy and free of impurities.

3. Clean the back of the vitrified brick to keep it free of dust, oil stains and gravel.

Vitrified brick is a widely used building material, which can be used for wall and floor decoration. However, in China, due to the lack of professional knowledge and experience of many construction personnel, the construction quality of glass pai bricks is unsatisfactory. The following is the method of vitrified tiles on the wall.

1. Wall treatment.

Before construction begins, the walls need to be treated. First of all, check whether the wall surface is flat; If it is not flat, you need to treat the wall with cement mortar to a flat state. If you find grease or other obstructions on the wall, you need to remove it.

In addition, if you need to carry out construction in a damp room such as a kitchen or bathroom, it is recommended to apply a layer of cement sand core Sakura slurry after treating the wall to prevent water and moisture.

2. Prepare the mortar.

Before starting construction, the mortar needs to be prepared. Generally speaking, it can be made by mixing cement and aggregate and adding an appropriate amount of water. If you need to work in a special environment, such as in a humid room, you can add a waterproofing agent to prevent moisture penetration.

3. Laying bricks. At the beginning of construction, it is necessary to lay the mortar on the wall and place bricks on the mortar. Then, use a hammer and spirit level to adjust the position of the bricks, making sure that the bricks are horizontal and vertical.

After laying each layer of bricks, it needs to be verified with a 10-degree angle of the goniometer to ensure its correctness.

4. Caulking. After the bricks are pasted, caulking is required. When making joints, the mortar should be coated with gaps, and there should be no dead ends. After filling the joint, clean it with a brush and mop for subsequent construction.

5. Clean up and decorate.

Finally, the construction site needs to be cleaned and the walls decorated. When doing the cleaning, you need to make sure that the wall is free of any dust or residue. The walls can then be decorated with decorative materials such as paint or tile adhesive.

In short, the construction of vitrified bricks requires experienced construction personnel. The above is the method of vitrified brick sticking to the wall, as long as you follow these steps to operate, you can ensure the quality of construction.

Whether decorated indoors or outdoors, it has a modern and elegant taste.

The following are 5 things that should be paid attention to when laying vitrified tiles:

1.Base wall inspection.

First of all, check whether the original wall is suitable for paving vitrified bricks, such as whether the wall is cracked, cavitation, etc., and whether the details of the wall such as waterproofing and brushing are qualified.

2.Fixing the bottom layer of vitrified bricks.

When the wall begins to be paved with vitrified tiles, it is first necessary to determine whether the tiles are level, and then when paving vitrified tiles, tools such as wood should be used to fix the support to prevent falling.

3.Increase adhesion.

When paving vitrified bricks, the content of cement mortar is slightly higher than that of ordinary wall tiles, and the adjustment ratio can be 1:2.

4.Off-seam paving.

This is a more common method of use in international decoration construction, the joint between bricks and bricks is generally 1-3mm, in addition, it should be caulked after 4 hours of paving.

5.Since the newly paved vitrified brick is not completely dry, try not to walk around on the brick surface to avoid uneven brick surface caused by man. In addition, it is best to cover the newly paved vitrified bricks with cartons or fabrics to prevent the pigments, paints and glues used in decoration from dripping on the brick surface of the vitrified bricks and polluting the brick surface.