Is it necessary to remove the insulation layer on the balcony tiles? What is the reason?

If there are crops attached to the surface of the wall, including the insulation layer, it should be completely removed, and the dust (ash) on the wall should be washed off with water. In order to improve the adhesion of cement mortar. The tiles can also be safe, strong and reasonable.

On the contrary, it may cause the cement mortar to reduce the thickness (continuity), and warping, bulging, loosening, layering and peeling and falling bricks, and finally endanger the actual effect and service life of tiles. Stencil insulation, interior wall paints, exterior paints, or waterproofing materials, melamine...and other decorative items. Gypsum board, lime powder layer, interior wall putty powder (paste), or other coating chemicals...

Wallpaper, wall coverings, plastic films, and other soot, oil pollutants...Wait. It will definitely endanger the assembly, (plastering) floor tiles should have a practical effect. After the insulation is removed, leakage and water seepage can easily occur.

Everyone is likely to not know much about the thermal insulation of the living balcony, which is all pasted with the internal and external walls of the living balcony, whether it is a pasted thermal insulation board or a wiping thermal insulation particles, the practice is all like this. Especially in the area where the balcony doors and windows are closed, there is thermal insulation to carry out the solution. If we remove the insulation, it will cause the edge of each hole to be exposed, and water seepage is easy to occur in the middle and later stages.

The temperature in the living balcony is too low. The temperature of the living balcony is too low, and the most fundamental factor is that the insulation layer has been removed. We may not think it would make a big difference to shovel off a little insulation, but I don't think so.

Since there is no thermal insulation in the future, our living balcony items will be particularly cold. Condensation can also occur in the summer. In fact, this is the result of the formation of a situation similar to a hot and cold bridge.

Solve the batch putty on the surface of the balcony insulation. At this time, people should first check the compressive strength of the batch putty on the surface of the thermal insulation layer, so that the sand can not fall. In addition, the surface of the insulation layer should not be hollowed out or falling.

In the event of the above situation, we have to shovel out this thermal insulation layer and then hang the label again to carry out a batch of putty.

The insulation layer of the indoor balcony is beautiful and generous, it looks suitable to immediately paste tiles on the top, but its compressive strength is relatively low, and it can not withstand the net weight of the floor tiles. As the master said, the insulation layer on the inside of the living balcony is because the neighbor's living balcony is sealed, so you don't have to worry about the heat in the room after scraping off the insulation layerAfter scraping, it will be much easier to put tiles on, and it can also make the tiles more solid, so you don't have to worry about the risk of falling off.

It is indeed needed; Because if you add tiles to the insulation, there is a high chance that problems will occur in a relatively short period of time.

Yes, if you don't shovel it off, it may not be very firm when you put the tiles, and it will fall off easily.

The balcony tile should be shoveled off the insulation layer above; Because the insulation layer on the balcony is made of foam board, the hardness is relatively low, it is difficult to bear the weight of the tile, and the flatness of the foam board is not very good, there is no way to absorb the components in the cement, so it is better to shovel it off.

1.The main reason why the insulation layer is removed is because the insulation layer is made of asbestos netting.

and foam made. It is not flat enough to absorb the moisture in the cement. It won't take long for the wall tiles to fall off, so if you want to put tiles on the balcony, be sure to shovel them.

If you want to seal the balcony at home, you can directly shovel off the insulation layer, because the outer wall of the balcony must have an insulation layer, and the window seal will not affect the insulation effect, just shovel off the tiles. Even if you don't have tiles, you can shovel it, because the insulation layer is at least 5cm, and shoveling it can expand the space of the balcony.

2.If it is a closed balcony, it is recommended to remove the insulation, because the exterior wall of the building will also have a protective layer, so for a closed balcony, the insulation inside is not so necessary. For balconies that are not enclosed, it is recommended not to remove the insulation layer, which can slow down the conduction speed of outdoor thermal imagery, and at the same time can play a good role in thermal insulation and improve indoor living comfort.

The insulation of balconies is generally asbestos netting and foam. These materials do not absorb cement mortar.

moisture, the surface is mostly painted for exterior walls.

or real stone lacquer decoration.

3.If the wall tiles are directly attached to the insulation, the wall tiles will not be able to adhere tightly to the infrastructure. In addition, the balcony is exposed to direct sunlight, which causes the insulation layer to expand and contract.

It will directly lead to tile peeling off or large areas of hollowing.

phenomenon. The insulation layer is relatively flat, but because of the foam used in it, although we can also paste tiles, but because the foam cannot absorb water, the tiles will not be pasted for a long time, and they will still fall.

4.If the insulation is removed, there will be no problem. The insulation layer is relatively flat, but because of the foam used in it, although we can also paste tiles, but because the foam cannot absorb water, the tiles will not be pasted for a long time, and they will still fall.

If the insulation is removed, there will be no problem. The main purpose of removing the original insulation layer of the balcony is to consider the tiles on the wall when decorating later, and the balcony tiles often fall off, so removing the insulation layer is only the first step in the decoration of the balcony. Pay special attention when tiling the balcony and try to choose ordinary tiles.

There is no need to shovel off the insulation layer above, because the insulation layer will not affect the tiles, the insulation layer can play a good thermal insulation effect, if the shovel will affect the insulation, so it is best not to shovel.

Will definitely be demolished. Because the insulation layer is made of foam board, it can play a relevant thermal insulation effect. If you put tiles directly on it, it will look particularly unsightly.

Yes, the upper insulation layer needs to be removed, because this insulation layer is generally not flat enough, and it cannot absorb the moisture in the cement, so it is not much use.

needs to be demolished; The insulation layer can not absorb the moisture in the cement slurry, resulting in the wall tiles and the base structure can not be closely fitted, and it is easy to drill off or hollow the phenomenon.

Exterior wall coatings are relatively strong and not easy to remove, and the labor cost is not cheap. If it's not loose and free of putty, then it's not shoveling. Use reinforced tile adhesive to add supporting facilities base oilIt can firmly adhere to the super strength of the floor tiles and is not easy to burst, the construction speed of the project is faster, and the cost of the comprehensive project is equal or even smaller than the basic practice.

If the balcony is closed, the architectural paint is removed and the wall tiles are fully pasted, it is not unsightly if it has no impact on the appearance. If the balcony is not sealed, it is best to ensure that the height of the railing is pasted to the half wall to prevent obstruction; Then the shoveling needs to do semi-finished product processing and maintenance, pay-off engineering construction, and at the same time consider how to close the convex surface of floor tiles and architectural coatings.

If the wall and living balcony have a thermal insulation layer, try to avoid destroying it when removing the architectural coating, so as to prevent the fracture surface from becoming branches, and the future heating and air conditioning will consume energy and burn money. If the balcony wall is made moisture-proof, you need to be more cautious when shoveling the architectural paint layer, a small crack is enough to toss for many years. This layer of lime must be shoveled off, whether it is tiled or sprayed with latex paint in the middle and late stages, it cannot be stored.

He can't make the premise fit with the surface raw materials, and if he doesn't shovel the damage caused by the middle and late stages, the cracks in the wall will blister.

Wall and exterior wall tiles are the process done by real estate developers before. The first is the quality of the brick itself, the second is the beauty of the brick, and the exterior wall tiles are all small bricks; If the insulation layer is not shoveled off, the middle and late tiles or paint will harm the bottom layer is not firm, resulting in the middle and late stage of the wall tiles falling off and the latex paint cracking. If it is a wall exterior wall coating, the wall tiles must be shoveled off, otherwise the cement mortar and the wall will fall off, and the floor tiles will fall off in the middle and late stages.

The normal construction method is to start the construction of the house, and the balcony insulation layer will be immediately removed and tidy when the wall is smashed, and then the balcony wall of the insulation layer will be removed during the construction of the masonry project, and then the next project construction will be carried out. There is a special thing to pay attention to when dismantling the insulation layer of the balcony, that is, the living balcony will be sealed normally, so the insulation layer should not be removed beyond the part of the sealed window, otherwise it is easy to seep water in the middle and later stagesIn the future, you will find that it has a very large role, is the key factor to ensure that the closed balcony is not seepage, are the first step, if this step is not done well, it is difficult to ensure that the closed balcony is not seepage.

Balcony tiling requires the removal of the original coating. Because if the original layer is not removed and the tile is re-coated and tiled, it may cause hollowing or aging of the previous coating, resulting in the problem of tile peeling.

There is no need to shovel it off, because it is easy to seep and leak after shoveling, and the temperature of the balcony is too low, and there will also be air leakage.

In the process of pasting tiles on the balcony, there is no need to remove the original layer, and the presence of the original coating can better waterproof. Tile pasting can be done directly on it.

For balconies that are not enclosed, the insulation layer can be unplugged or not. If you don't plan to remove the insulation layer and want to paste some solid tiles, there is another way: add barbed wire to the outer wall of the insulation layer, then apply gypsum mortar, then apply flexible mortar, and finally use nails to drive it into the wall to paste the tiles.

<> balcony tiling or not, whether to shovel the insulation layer depends on the situation, if the family chooses to seal the balcony.

Then the insulation layer needs to be removed before tiling. Because the balcony is sealed, there is no need to worry about uprooting the insulation that will make the indoor temperature run away, so it seems that the insulation is not necessary. Although the insulation of the interior balcony looks flat and is suitable for the appearance of direct tiling, it is due to the asbestos netting.

And in the form of foam, the hardness is very low, it is difficult to bear the weight of the tile, and it is also difficult to absorb the moisture in the cement, so the tile is just easy to fall off.

Do you have to remove the insulation before tiling your balcony? That's it, so don't be fooled! Because I chose to seal the balcony, my girlfriend asked whether to seal the balcony first or paste the porcelain first?

Tiles will stick more firmly after removing the insulation, while also expanding the balcony space, as some small homes can choose to do. Whether the insulation layer is to be removed depends on the situation; If it is a closed balcony, it is recommended to remove the insulation layer, because the exterior wall of the building will also have a protective layer, so for the closed balcony, the insulation layer inside is not so necessary; For unenclosed balconies, it is recommended not to remove the insulation layer, which can slow down the conduction speed of outdoor heat, and similar to this, it can still have a good thermal insulation effect and improve the comfort of indoor living at the same time.

Do a detailed explanation of the problem for a detailed interpretation of the problem, I hope it will help you, if you have any questions, you can leave me a message in the comment area, you can comment with me more, if there is something wrong, you can also interact with me more, if you like the author, you can also follow me, the like is the biggest help to me, thank you.

There is no need to shovel off the upper insulation layer, because if all the insulation layers are directly removed, our house may not be insulated in the future, which is not good.

There is no need to do this, the insulation is very important, if there is no winter time it will cause the indoor temperature to drop, and in the summer the temperature will be particularly high.

When tiling the balcony, try not to destroy the insulation layer. Because the original insulation is maintained, it is very comfortable for future living.

The balcony is an important part of the home, and this area can meet many of our movements, such as using it as a drying area and a relaxation area, and it can also be transformed into a laundry area. No matter what kind of area it is, it can show its perfect side, and if it is well designed, it can also bring our overall interior space to the highest level. If you want to tile the balcony, you have to take into account some problems, such as the existence of insulation on the original wall, then it must be completely eradicated before you can paste the tile.

So what is the reason for this? Let's talk about this topic for a while. <>

The reason why the insulation layer will be made on the wall of the balcony is because the energy-saving standards promulgated by the state stipulate that new buildings must be mandatory to do the insulation layer of the exterior wall. If this insulation layer is not removed, it can also achieve a good use effect, but most families do not use this insulation layer, especially in the south, the insulation layer will be removed, and the tiles will be paved to maximize the use of the balcony. So why do you need to shovel off the tiles before you can put them on?

Because the tile and the wall must achieve a tight fit in order not to fall off, the tile on the insulation layer is not attached, because the insulation layer is a layer of foam, a large area of tiles may not be able to bear the weight, collapse is possible. <>

Therefore, it is necessary to shovel all the original insulation layer of the balcony clean, and then carry out a flat treatment on the wall, and only after the treatment is completed can the tiles be paved. There are also certain requirements for paving tiles on the balcony, that is, the material of the tiles should be sunscreen as much as possible, because the balcony will be sunburned for a long time, and ordinary tiles will change color after being sunburned for a long time, which will affect the overall effect of our space for a long time. And sunscreen will not change color no matter how the sun shines, which can not only achieve the effect of sun protection, but also achieve an aesthetic effect.