The balcony is going to be tiled, do you want to shovel off the insulation layer above?

So I wanted to remove the insulation. So do you need to eradicate it? I will answer the following questions to you about the treatment of balcony insulation.

The master actually said that if he pasted it, he would scrape off the insulation layer on the inside of the balcony, isn't this a pitfall? Can't you just stick it on the balcony? To tell the truth, the master is really not a pit for him, my tiles are directly pasted on the insulation layer, and the master actually said that if you paste it, you will have to scrape off the insulation layer on the inside of the balcony, isn't this a pit person?

Can't you just stick it on the balcony? To tell the truth, the master is really not a pit for him, my ceramic tiles are directly pasted on the insulation layer but the balcony is to be tiled, the insulation layer seems to be flat, very suitable for tiles, but the materials of the insulation layer are mainly asbestos and foam, it can not absorb the moisture of cement, so the tile will be hollowed out or even fall off soon after it is pasted.

Now many exterior walls are insulated, the exterior walls are pasted with exterior wall tiles, the premise is to hang steel wire mesh, mortar leveling directly after the bricks, there will be no problems, those who say that the insulation layer must be shoveled off are laymen. The north can not be demolished, seal the balcony, close to the house can be demolished, by the outside can not be demolished, because it is directly in contact with the cold air outside, if there is a water pipe in the balcony afraid of winter, stick the brick water beads, with the insulation layer sticky, find a good bricklayer. For example, the waterproof base layer is "snatched up", such as the water and electricity heating line, and the "walk" again, such as the railing "don't".

What does this emblem? The limitations of architectural design, the low-end of construction, the courage of decoration, and the money to buy a house to chisel off the balcony insulation layer lead to the destruction of the closed-loop insulation system of the whole house, which may affect the thermal insulation effect of the house. If there are construction quality problems in the construction of the insulation layer, and the conditions for tiling cannot be met, you can ask the developer for rectification.

If you put tiles, it is recommended to shovel them out, so that the space of the house will be larger. If you stick tiles on the insulation, it is the length of time to say, it depends on the master you are looking for, and then the materials are said to be chiseled and brushed after the demolition, the glue used for brushing is not mixed with water, and the purchase of tiles is as much as possible to buy more weather-resistant exterior wall tiles, and the interior wall tiles are paved on the balcony and are affected by the climate, which is prone to cracking and delamination.

I don't think so. First of all, if you put tiles on top of the insulation, it will not affect its beauty, and it can ensure that the indoor temperature is very suitable in winter.

I think it's better to shovel off the insulation layer, because it is easy to burn and will have a very large odor, which is not good for children's health.

I advise not. The insulation layer is used to protect the temperature of the room, and if it is removed, it will cause excessive loss of room temperature.

How to tile the insulation layer of the balcony

1. Generally speaking, the inner surface of the balcony has an insulation layer, and many people will directly remove the insulation layer. If there is insulation, can it be tiled? If there is insulation, it is possible to apply tiles.

2. You can directly plaster the surface of the balcony, then use special coagulant materials, paste the insulation board on the wall of the balcony, and then fix the insulation board with insulation nails, and finally hang the fiberboard, and then plaster, you can paste tiles on the cement wall.

3. However, when pasting tiles, we must pay attention to the gap between the tiles to keep a certain distance to avoid thermal expansion and cold contraction, and the phenomenon of arching.

4. The insulation wall is a special wall, if the strength is not up to the standard, the tile can not be pasted successfully, not to mention hanging other objects. If you have to do it, you can also remove all the insulation layer, and you can also increase the area of the balcony, and wait until the cement wall inside is exposed, you can directly paste the tiles. However, in this way, it will also lead to the thermal insulation performance of the balcony will become very poor, and the balcony door can be installed later to isolate the temperature.

Thermal insulation wall, it is a special kind of wall, not to mention the low strength, even the weight of the tile is difficult to bear, not to mention the metal pendant after the tile is pasted. If you have to do it, then the best way is to remove the insulation layer, and at the same time, this method can also increase the area of the balcony, and wait until the cement wall is exposed for tiling, but in this way, the insulation of the balcony will become worse, it is recommended to install a balcony door to isolate the indoor temperature.

If you want to keep the insulation wall, and you want to put tiles, you can also do it. But the premise is to look at the construction sequence of the balcony insulation layer, when the sequence is the wall, the insulation layer, galvanized mesh, cement mortar, you can treat the wall and then paste the brick; When one of the items is missing from the sequence, it needs to be replaced and tiled with high-standard cement or adhesive. Even if there is such a method, it is still necessary to note that the insulation layer of many buildings is now on the inner side of the load-bearing wall, in order to enhance the thermal insulation of the house, so many times the insulation layer becomes the inner wall of the room wall, but because the strength of the insulation layer is very low, it is best not to directly paste the tiles, and the firmness will be very poor.

One way is to remove the insulation layer, this way is suitable for the balcony to be completely closed, used as an indoor balcony, after the insulation layer is removed, the original wall plastering leveling and brushing treatment, and then the tiling, with the adhesive mortar for paving, the advantage of removing the insulation layer is that the space of the balcony will be larger, and the other way is to hang the net and paste the brick, directly install the steel mesh on the balcony insulation layer, and fix it on the wall with expansion screws, this way is similar to the cement pressure plate hanging net and tiling, and it is easy to fall off the hollow drum.

Because the insulation layer is hollow foam, it is the sound of hollow drums. Therefore, it is possible to put tiles on the insulation layer, but it is impossible to check whether there is a hollow drum problem when laying tiles.

It is definitely possible to put tiles, because the insulation layer is on the outside, so the tiles are just right on the inside.

In terms of thermal insulation, the insulation layer of the balcony is usually made of asbestos net and bubbles, which mainly has the effect of thermal insulation, but the material absorbs the moisture in the cement mortar, if the ceramic tiles are directly paved on the insulation layer, the adhesion of the cement may be greatly reduced, and the insulation layer has been exposed to the sun for a long time, and the ceramic tiles may be hollowed or fallen off in a large area due to thermal expansion and contraction. Tile paving is the use of cement mortar and tile surface bonding, the common base surface may be due to pasting, paste method of the wrong and hollow, falling off, at the same time with other materials of the waterproof wall need to add cement mortar bonding, and for the balcony there is a thermal insulation layer where there will be no hollowing, and reduce the bonding of cement mortar.

<> whether it is the insulation layer or the original wall, as long as it is a tile, it is necessary to make a scratch off the cocoon on the wall of the original room, so as to enhance the rough roughness of the tile and adhesion, and the insulation layer is composed of insulation cotton and outer coating, the tile and cement are not fixed, if forced paste, it is also very likely to fall off. At the same time, after the cancellation of the insulation board, if the wall is very light, it is also necessary to turn the light wall into a pothole-ridden surface, because the wall is rough, the greater the friction, the better the adhesion of the cement, and the stronger the brick.

In addition, the insulation layer itself has a material problem, the bearing capacity is poor, the overall gravity of the tile and the cement mortar is very large, and the insulation layer is difficult to withstand the overall gravity, resulting in the tile falling off. The asbestos net and the foam itself can not absorb the moisture in the cement mortar, and the moisture in the cement mortar cannot be absorbed by the base surface, the adhesion between the base surface and the cement mortar will be reduced, the tile and the base surface can not be closely adhered to, and the bond strength is also relatively reduced, and the problem of tile falling off in the later stage will naturally occur. The balcony is based on the entire building space, it is the most direct face to the sun, long-term natural exposure, the insulation layer will produce thermal expansion and contraction changes, the tile and the base surface will deviate, and a large area of hollowing or even falling off will occur after a long time.

Because the tiles of the balcony are exposed to the outdoors, if there is an insulation layer, the tiles will not be broken due to the sun or cold weather, and they are more durable.

Because the tiles on the balcony have a protective layer on the top of the wind and sun, it will make the tiles more durable, even in extreme weather will not break.

It may be a protective effect, as it will prevent moisture and burst problems.

When the wall is renovated, many homes will put tiles on it. Will the balcony insulation fall off if the tiles are not removed? PChouse will take you to find out.

1. Although the insulation layer looks relatively flat and suitable for direct tiling, the insulation layer is mainly asbestos net and foam, which can not absorb the moisture of the cement, and will fall off if the tile is pasted on it for a long time. However, this will not be the case if the tiles are applied after eradication.

2. Check the strength of the plastering on the surface of the insulation layer, and do not allow sand to fall. In addition, it is known that in addition to grinding and dismantling, the surface of the insulation layer can not be hollowed out and fall off. In the above situation, we must shovel out these insulation layers and re-hang the net for plastering.

3. For pasting tiles on the balcony wall, it is recommended to use a tile adhesive with a high adhesion force to paste. It is not recommended to use ordinary cement mortar for pasting. Because of the tile adhesive, we can try to use the thin paste method, so as to meet the paste of the tile.