-
In daily life, many of our bags are zippered, which is convenient for our lives, and at the same time, it also brings us trouble. It's easy to break, so what to do when the zipper breaks. Let's take a look at how to repair the zipper.
First dial the top tooth of the zipper with pliers, and then pull the lock of the zipper to the top on both sides, and then merge the teeth on both sides and then put the zipper lock into it (there is a certain degree of difficulty, because the diameter of the metal zipper is thicker, if you really can't fit in, cut a small hole on the radial line, remember, don't cut it in the place where the big tooth is installed, it should be cut by the top place, otherwise the big tooth will not fit up).
After the zipper lock is put in, everything is OK when the big tooth is installed, and if the opening and closing are not smooth, if you pull the chain head hard, it will cause a tooth element occlusion failure. At this time, paraffin wax or lubricating spray is applied to the surface and inside of the tooth, and then the slider is moved several times before sliding easily.
If you really can't: when opening and closing the zipper, sometimes the chain head bites the line segment or the cloth and makes the slider unable to pull the case, if you force the slider to pull, it will bite deeper and deeper, you should turn the slider backwards on one side, and untie the cloth on the other side. When you bite into it completely, do not pull the slider vigorously, but slowly reverse the slider.
And when sewing zippers, don't leave hidden dangers.
If you want to solve it temporarily, use pliers to clamp the tail of the slider, pay attention to the tail, but be careful not to use too much force or clamp off, if you want to completely solve it, you have to replace the slider. Zipper repair is actually very simple, precautions to pay attention to maintenance when using. You can apply some lubricating things like soap from time to time.
If the zipper is broken, you have to replace the entire zipper, which is generally more troublesome.
-
What should I do if the zipper puller is broken? This trick will give you a new look.
-
Nowadays, many things are broken zipper pulls, such as some pants and clothes can be directly taken to a nearby splitting point, and they can help you change a slider.
-
First, pull off the top tooth of the zipper with pliers, and both sides should be dialed. Then pull the lock of the zipper to the top, and then merge the teeth together. Then put the zipper lock into it, there is a certain difficulty, because the diameter of the metal zipper is thicker, if you really can't put it in, cut a small hole on the radial line, remember, don't cut it in the place where the big tooth is installed, it should be cut by the top place, otherwise the big tooth will not be fitted.
After the zipper lock is put in, put the big tooth on and it's OK.
-
If the zipper puller is broken, you can replace it with a new slider. Generally, shops that modify clothes outside and shops that polish shoes or maintain leather goods can replace the zipper pull.
-
First, if the zipper is not flexible, consider that the zipper may be damp or rusty, especially after the iron zipper oxidation will cause it to be unsmooth when pulling, and when it can't be pulled hard, you can actually put a candle or soap on it back and forth, and then wipe it off and you will find that the zipper is smooth.
Second, if the zipper can't be opened, the problem may be on the slider, the slider is generally made of two pieces of metal, and after a long time, the distance between the metal sheets will be widened, and the zipper will not be opened. At this time, you only need to use pliers or teeth to gently bite up and down or left and right, but the force should not be too large, be careful that it will break.
Third, if the zipper is missing teeth, you can pry the zipper teeth open with pliers or a camera at the original tail to remove a few teeth, install them after the tooth is lost, and then let it be tightly stuck in the notch, and pull it back and forth several times to ensure that it is close to the notch.
-
Main tool: a piece of clothing with a broken zipper head.
Auxiliary tools: scissors, straws, hot melt adhesive.
Pincers. Steps to get started:
1. Prepare a straw.
2. Use scissors to cut a length of about two centimeters.
3. Cut the straw from the middle.
4. Then turn the straw on.
5. Then fold it in half from the middle.
6. Then place it on the edge of the damaged zipper puller.
7. Then stick it with hot melt adhesive.
8. Fold it back in half and pinch it tightly, and wait for the glue to dry.
9. After waiting for the glue on the previous side to dry, turn the clothes over and stick the bottom of the zipper puller with hot melt glue.
10. Then pinch it tightly in the same way.
11. Then clamp it hard with pliers along its edge.
12. Then use scissors to cut off the excess part of the straw.
-
Tools required: taper pliers, scissors, needle, thread.
Steps: 1. We pull the zipper to the very bottom, make a comparison with the side of the zipper, and find the chain teeth parallel to the zipper head.
2. We use scissors to cut off this chain tooth.
3. Next, there is a gap after cutting.
4. We put the zipper through this notch.
5. Pull it up and get it back on track.
6. Sew the mouth of the chain teeth cut with a needle and thread, and sew it a few more times to make it firmer, so that when you pull the zipper down again, you don't have to worry about the zipper head running out.
7. After the repair is completed, use pliers to clamp the two ends of the zipper slightly.
8. The repair is complete.
-
For the broken zipper pull, the materials you need to prepare include: a new zipper pull.
First, at one end of the zipper, find a groove.
Second, then pull the broken zipper puller diagonally outward, so that one corner of the zipper puller slides out along the groove.
3. In this way, the bad zipper puller can be removed.
Fourth, then look at the number behind the zipper pull, which represents the model.
5. Find a zipper puller of the same model, and slide one corner of the new zipper puller into it along the groove just now.
Sixth, this will replace the broken zipper puller with a new one.
-
Pull the zipper puller to the bottom of the zipper of the garment, diagonally outward, so that one corner of the zipper puller slides out along the groove, and continue to force your fingers to slide the zipper puller out along the groove to the outer corner. After removing the broken zipper pull, look at the model number on the back of the zipper puller and find a zipper puller of the same model. Thread the new zipper puller through this chute in the same way as you take the zipper pull, and the zipper puller can be replaced.
1. Pull the zipper puller to the bottom of the zipper of the clothes, pull it diagonally outward, let one corner of the zipper head slide out along the groove, and continue to force your fingers to slide the zipper puller out along the groove to the outer corner.
2. After removing the broken zipper pull, check the model on the back of the zipper pull, and find a zipper head of the same model.
3. Use the same method as the zipper puller to thread the new zipper head through this chute, and then you can replace the zipper pull.
First of all, don't worry, it's a very patient problem to open under the zipper, first of all, calm down, take a drink, untie your clothes, cool and cool. >>>More
Zippers are always indispensable in our daily life, not only our pants, coats, quilt covers and these dolls, the zipper on it is broken, because a small zipper throws away all these broken things, it is inevitable that there will be a little waste, so today I will share with you several very common ways to repair zippers. >>>More
Have you ever been in this situation where the zipper of your clothes has been accidentally broken? >>>More
If the zipper of the mosquito net is broken, if you want to fix it, you can sew the side up with a needle, so that it can be used.
1. First find the installation direction, there is a small bump on the zipper, facing up, don't make a mistake, the zipper will not be smooth. >>>More