How to put the zipper on the bag back if it falls off

Pry the slider open a little bit and put it on it, just knock it on, first tuck one zipper into one side of the head, and plug the other side. When you plug the other side, it may get a little stuck, so don't stuff it in, don't ask for the same length on both sides, just hold it with your hand. Then hold the protruding head of different lengths and pull the zipper in the opposite direction, at this time the zipper is not closed, but the zipper is already closed, but the length of the two sides is asymmetrical.

Pull it to the end of the opposite direction, hold the short end and pull it back, and the length will be adjusted. Pry the slider open a little bit, put it on, and knock it on.

1. Generally, it will come out at the end of the opening, open the zipper, and you can put it on from the very top. If there is a jam on the top, just pull it out and you can wear it in.

2. The installation position of the zipper head is divided into left and right, find the wide side below, and load it upside down from the top of the zipper, and it is best to sew the top of the zipper with a needle and thread after loading, so as not to fall off again.

After the zipper is on, the other end of the zipper is pulled out of the cloth on both sides, and the key action is to insert two needles into the zipper on both sides, push it to both sides, and at the same time slide the zipper inward, and it is very easy to slide in.

If the zipper on the bag falls off, you can't put it back because it's broken, and you can take it to sew clothes, and let him install it for you.

Here's how to put the bag back in when the zipper puller falls off:

Prepare materials: bag, zipper, screwdriver, fork.

1. Use a screwdriver at home to remove the parts at the end of the zipper.

2. Place the new zipper on top of the fork.

3. Place the zipper on top of the new zipper pull.

4. Put the parts at the end of the zipper back on.

5. Finally, the zipper of the bag was repaired.

The zipper puller has fallen off, how can I easily put it back in? It's actually very simple, and you can learn it at a glance.

I pried open the two zippers with a flat-neck screwdriver and took them off with a single click.

If you really can't get it down, ask someone else to take a look.

How to repair the zipper of the school bag: use pliers, candles, etc.

1. With pliers:

The zipper of the schoolbag can not be closed can be repaired with pliers, often pull the zipper diagonally upwards will make the zipper lock loose, take a pliers, clamp the zipper lock, press it gently, press the lock tightly, and then pull the zipper to close.

2. Use candles:

If the zipper of the bag cannot be closed, it can be painted with candles, if the zipper does not move, it means that it has rusted, resulting in the zipper cannot be closed, the candle is painted on the zipper, and then wiped with a paper towel, the friction will make the rust of the zipper fall off, so that the zipper can be closed.

Zipper maintenance tips:

1. When using it at ordinary times, it is necessary to pay attention to whether there are problems such as "broken belly" and "tooth loss" on the zipper, and these problems should be repaired in time and not deadlifted. If the zipper is loose and the teeth are missing, you can use a small hammer to gently knock a few times on the zipper head to make the upper and lower chain teeth bite tighter, and the teeth will not be removed again.

2. The zipper of aluminum alloy is more susceptible to corrosion, so it should be kept dry, not damp, and should also be careful not to contact with alkaline and acidic substances. When storing, it is necessary to ensure a certain degree of ventilation, do not store it in a sealed environment, and do not store it in a humid environment, and use moisture-proof paper or dehumidifier if necessary.

3. When pulling the zipper, you should first align the teeth on both sides, and then pinch the zipper head and gently pull it forward along the track, do not pull hard, so as not to cause "crooked teeth", "broken belly" and "only stop the teeth".

The method is as follows: 1. First use the blade to cut the thin line at the end of the zipper, and the purpose of this step is to free the end of the zipper.

2. After cutting, the end of the zipper is exposed.

3. Put the zipper on the upper side into the zipper pull.

4. Put the zipper on the lower side into the zipper pull.

5. Therefore, the zipper can continue to be used.

Prepare tools: pliers.

Step 1: Open the zipper of the schoolbag to the bottom, and expose the top of the slider.

Step 2: Clamp one side of the slider with pliers and clamp it upwards. (Be careful not to clamp the sides of the zipper so as not to break the zipper).

Step 3: After clamping off one side of the slider, use the same method to clamp the other trapped side. (The other side only needs to be clamped roughly).

Step 4: Clamp to the following figure, and finally pull the slider diagonally.

Note: When using pliers, pay attention to the position of the clamp bite, and never clip the zipper; If the slider's loop affects the operation, you can remove the loop first.

Replace in five steps:

Tools required: 1 new zipper pull, 1 blade.

1. Use a blade to cut the thin line at the end of the zipper, and the purpose of this step is to free the end of the zipper.

2. After cutting, the end of the zipper leaks out.

3. Put the zipper on the upper side into the zipper pull.

4. Put the zipper on the lower side into the zipper pull.

5. Therefore, the zipper can continue to be used.

Note: The end of the zipper can not be sewn to death, as long as you pay attention to the zipper does not pull to the end.

The bag zipper is separated and repaired as follows:

First, the zipper is rough.

Slowly pull the zipper to the end of the zippered bag, so that you can pull the zipper back smoothly, if the zipper is stuck by the bag cloth, you must separate the bag cloth from the zipper. Apply some lubricant to the zipper and rub it back and forth.

Lubricants can be soaps, pencil ends, lip balm, and more. After adding lubricant, lay the zipper flat, then slowly pull the zipper to the other end, and if there is resistance, you can stop and add some more lubricant. Pull the zipper back and forth to see if the zipper is still separated.

Second, the zipper is loose or broken.

If the zipper is loose, you can press the zipper with pliers. If it's because the zipper is broken, you first need to remove it with pliers. Then attach a new slider and clamp it tightly.

How to choose a school bag

1. Tailor-made purchase. Pay attention to whether the size of the bag is suitable for the child's height. Consider a small bag and choose the smallest one that can hold your child's books and stationery.

In general, the bag should not be wider than the child's body; Carry it on your back, and the bottom of the bag should not be 10 cm lower than the child's waist.

2. Focus on design. When parents buy a schoolbag for their child, they should not ignore whether the internal design of the schoolbag is reasonable. The internal space of the schoolbag is reasonably designed, which can classify children's various books, stationery and daily necessities, which can cultivate children's storage and sorting ability from an early age and let children develop good habits.

3. The material should be light. The material of children's school bags should be light, because students have to carry a large number of books and items back to school, so in order to avoid the increase in the load of students, school bags should be as light as possible.