Where is the installation location of the surface mounted copper and aluminum radiator?

Surface-mounted copper and aluminum radiators are generally installed in hidden locations, which can be beautiful, such as in the corners of walls or under window sills.

The installation of the radiator of the surface-mounted wall-hung boiler is divided into parallel, series and octopus test, the heating parallel installation method is the most used installation method at present, and the advantage of parallel connection is that there are multiple temperature control valves and multiple pipes, which can control the temperature of the radiator separately, and will not cause uneven temperature in the room. In the unlikely event of an accident with the radiators, such as water leakage and corrosion, the temperature control valves of the radiators can be closed and repaired and replaced, leaving the radiators unaffected.

After the installation of the radiator of the surface-mounted wall-hung boiler, the radiator is not hot.

The radiator part is hot and the part is not hot, mainly because there is air in the radiator, just vent the radiator. Steps:

There is an exhaust valve on each set of radiators, gently twist the exhaust valve, stop twisting the exhaust valve immediately when you hear the exhaust sound, and close the exhaust valve if you see a steady flow of water.

The radiators in the exposed buckets are installed under the windows, or in the kitchen and bedroom.

Wear the tall vertical radiator horizontally as a low one. Although this is not the reverse installation of the radiator, it will also cause the hot water circulation in the heating to be poor. Therefore, if you want to install a short film, don't buy a vertical back horizontal dress, which will affect the heat dissipation.

Install the radiators in and out in a way that goes down in and out up. This situation will form a circulation of water is very slow, the radiator can not heat up, and the need to change the pipe from scratch is a good cover.

Bottom in and bottom out type: the heating left in and right out of the water socks filial piety method into the right in and left out. The left side of the radiator is the water inlet pipe, and the right side is the return pipe.

The time and minutes of the device are installed in right in and left out. It needs to be noted that there is a stop alarm plate in the radiator (generally close to the baffle to connect to the water inlet, far to connect the water outlet), and other water inlet and outlet methods are not. Therefore, if it is installed in the opposite direction, the hot water will not be able to circulate.

1.The radiator should be handled with care during handling to avoid damage, and special attention should be paid to protecting the spraying surface from scratches. The radiator should be stored in a ventilated and dry warehouse, classified and discharged according to model and size, with a height of no more than meters, and the bottom should be stored 20cm high.

2.The installation method of copper-aluminum composite radiator can be made into bottom-in and side-out type and side-in and side-out type according to the design requirements.

3.Before the installation of the radiator, the import and export protection should be removed, the pendant should be placed according to the position of the fixed hole, and then the radiator should be hung, adjusted and fastened, and the radiator should be 25cm from the ground

4.The radiator thread is processed and manufactured in strict accordance with the standard J T6-1999 of the Ministry of Construction, and generally adopts two kinds of conical pipe pattern or cylindrical pipe thread.

5.For system experiment and operation, please pay attention to the hot water should not exceed the rated working pressure value. The steam should not exceed the gauge pressure), and an automatic pressure reducing valve should be set.

How to install radiators.

1. When opening the package, please carefully check whether the radiator model, color, and accessories in the package are complete. Accessories include, 1 plug, 1 bleed valve, 3 brackets.

How to install radiators.

Second, the inlet valve and outlet valve must be installed, and do not ignore these processes in order to save money.

How to install radiators.

3. During installation, the pipeline should be transformed according to the installation drawings of this book.

How to install radiators.

Fourth, pressure test: close the main connection valve, open the radiator inlet valve with pressure test equipment to test, the experimental pressure should be times of the normal use of pressure, and not less than the experimental pressure of the entire community pipe network, 3-5 minutes without leakage is qualified.

How to install radiators.

5. The fixed radiator pendant should be positioned with a horizontal ruler effect to ensure that the radiator is horizontal and vertical, and the connection between the pipe fittings and the radiator is accurately connected.

How to install radiators.

6. Please do not open the protective film of the inner packaging during the installation process, so as not to damage or scratch the paint film.