How to deal with the plaster line when it is dirty, and what to do if the plaster line in the room f

In order to make the interior decoration effect more beautiful, many families will use gypsum line to decorate the house, the gypsum line will be used for a long time, it will inevitably be stained, affecting the aesthetics, so how to clean up the dirty gypsum line?

How to clean a dirty plaster line.

1. If the gypsum line is only soiled by dust, then as long as you use a dry brush to gently sweep the dirty area, you can clean up the dust. When sweeping, it should be swept along the horizontal position, so that it can be cleaned more cleanly.

2. You can also use a dry brush to clean up the dust, and then sprinkle some water, when the water is about to dry out, spray a thin layer of gouache pigment solution on the surface of the gypsum line, and when the water pigment solution is dry, spray a thin gouache pigment solution again, so that the surface of the gypsum line at the repair position has the texture of gypsum.

3. If the gypsum line is only stained with some stains on the surface, then just use a knife to gently scrape off the thin layer of the surface of the plaster line where it is soiled.

4. If it is a gypsum line that has been used for more than 20 years and is very dirty, then you can first dilute ammonia and soapy water according to a certain ratio, and stir it sufficiently, and then use a rag dipped in some solution to gently scrub the dirty area, and finally use water to wash it again.

5. If the gypsum line is stained with ink stains and has penetrated into the gypsum line, then the ink stain position should be dug out first, and then a new gypsum slurry should be prepared according to a certain proportion, and fully stirred, and then applied to the ink stain position, so that the gypsum slurry can fill the ink stain position.

6. When the gypsum slurry is dry, use sandpaper to polish the surface of the gypsum slurry. If you are afraid that the color of the old and new plaster slurry will be inconsistent, you can use the plaster paste to apply the surface of the entire plaster line to make the color consistent.

The above is a detailed introduction on how to clean up the dirty plaster line, I hope it can help you solve the problem of the plaster line being soiled. If the cause and degree of staining of the plaster line are different, the treatment method is also different, and everyone should deal with it according to the actual situation.

If the plaster line is dirty, generally if it is dust, then use some guts to dust it off, if it has changed color, then there is no way to deal with it, it is best to brush a layer of latex paint on the plaster line, so that it can be!

First of all, use high-grade gypsum powder to add the special adhesive glue for the gypsum lineStir evenly, use the shovel paste, according to the meridians of the gypsum lines to "carve", and when there is a little hardness, then brush the water, but not everyone can do the repair of the gypsum wall in the decoration. Secondly, if the color of the plaster line is not satisfied, it can be refreshed with paint.

Gypsum line is the decoration material of the house, the main interior decoration. It can be practical and beautiful with various patterns, with fireproof, moisture-proof, heat preservation, sound insulation, heat insulation functions, and can play a luxurious decorative effect.

Tap to listen. You can use your fingers to gently tap the plaster line, if the sound is muffled and mostly inferior plaster line, if the sound of tapping is brittle, or even has a ceramic-like sound, then it means that the quality of the plaster line is good. Check the elasticity of the gypsum board, tap it with your hand, and make a very solid sound, indicating that the gypsum board is strong and durable; If it makes a very empty sound, it means that there is a hollow drum in the board, and the texture is not good. The weight of the plasterboard can also be measured by hand.

Generally, the concave and convex patterns of gypsum relief decorative products should be more than 10mm, and the production is fine. In this way, after the installation is completed, the surface can still maintain a three-dimensional effect and reflect the decorative effect. If the pattern pattern of the gypsum relief decoration product is shallow, only about 5 9mm, the effect will be much worse.

The reason for the detachment of the gypsum line from the wall is that the leveling treatment of the wall is unqualified, which is a construction quality problem. Solution:

The gap is too large, first scrape the putty on the wall, carry out appropriate leveling treatment, and then paint it.

If the gypsum line wants to be firmly bonded, it should first be adjusted with glue to speed up the adhesive powder.

The spacing of the installation points with the point should not be too large. What's more, after the line is angled to the corner of the wall, it must be pressed hard for more than a minute.

It is operated with latex gloves to prevent the glass filament from pricking your hands.

Apply the spilled quick-tack powder with your fingers to fill in the visible gaps.

Note: Immediately after that, clean the surface of the plaster line with a brush dipped in water. After drying, it is difficult to handle the smooth and slippery.

Method 1: When you are just contaminated, you can soak it in cold water or light salt water for a few minutes (do not use hot water, because the blood contains protein, it will coagulate when heated, and it is not easy to dissolve), and then wash with soap or alcohol.

Magic weapon: cold water, light salt water).

Method 2: You can use lemon juice and salt water to remove the stains, or you can use white radish juice or mashed carrots mixed with salt to remove the stains.

magic weapon: lemon juice + salt water; radish juice + salt; Carrot + salt) method 3: remove stains with enzyme laundry detergent, the effect is very good;

Magic weapon: add enzyme laundry detergent).

Method 4: If the stain time is long, you can use 10% ammonia or 3% hydrogen peroxide to wipe the dirt, and after a while, wash it with cold water.

Summary. 2. If there is a large crack but there is no damage, you can choose to repair it.

If there is a large crack in the gypsum line, but the plaster is not damaged, and the crack is not in the ceiling or other places that are easy to fall and affect safety, we can take a knife and cut a V-shaped incision along the cracked place, and then use gypsum powder to glue for repair, or we can directly use a special gypsum line to repair the glue. When you fill it, be sure to clean up the excess glue around it in time, and then use a hair dryer to dry it, so that the plaster line is not only strong and durable, but also does not show that it has been repaired at all.

How to repair the plaster line.

Hello, how to repair the cracks of the gypsum line: 1. If the cracks of the gypsum line are not large, or there are some stains that cannot be removed on the surface of the wax, then we can use the same color pigment or latex paint to spray it, so that the cracks can cover the wax.

2. If there is a large crack but no damage, you can choose to repair if the gypsum line has a large crack, but the gypsum is not damaged, and the place where the crack is found is not in the ceiling or other places that are easy to fall and affect the safety of filial piety, we can take a knife and cut out a V-shaped incision along the cracked place, and then use gypsum powder to glue for repair, or you can also directly use a special gypsum line to repair the glue. When you fill it, be sure to clean up the excess glue around it in time, and then use a hair dryer to dry it, so that the plaster line is not only strong and durable, but also does not show that it has been repaired at all.

3. If there is a crack in the key part, it is necessary to decisively replace the gypsum line, if there is a crack in the upper space of the wardrobe or the stone or old plaster line on the roof, then no matter the size of the crack, it must be replaced decisively. Because once there are cracks in the appearance of these areas, the situation of the pasted hall inside cannot be guaranteed, and it is even very likely that there are large gaps inside. If a fall occurs under the influence of gravity, it will induce a safety accident.

Enter the area and get the installation and burn repair for free**].

After being used for a long time, the gypsum line will inevitably crack and turn yellow, which will affect the appearance. So how to solve the yellowing of the gypsum line? What is the reason why the plaster line turns yellow? Let's take a look!

How to solve the yellowing of the gypsum line:

First of all, you must first find the yellowed place, then use a knife to remove the yellowed plaster line, and sand it with sandpaper. Secondly, lightly apply a layer of putty powder to the surface. Finally, wait for the putty powder to dry thoroughly before applying latex paint.

What are the causes of the yellowing of the plaster line:

There are two main reasons for the yellowing of the gypsum line, one is that in order to save time, the decoration workers apply the second and third putty before the first putty is dry, which causes the color to penetrate outward, and then discoloration. The second is that the sealing primer is not brushed before brushing, and the substrate is too alkaline to cause the paint surface to turn yellow.

How to clean the plaster line:

1. When there are stains on the gypsum line, just use a knife to scrape off the stains, and then use Zhaoye gypsum powder to mix gypsum slurry to fill the dug holes, and wait for the paint to dry thoroughly, and then use something to smooth it and grind it.

2. When stains appear on the gypsum line, gypsum water can be made of gypsum powder to fill the stains. Add 50g of quicklime and 1500ml of water to make gypsum water, stir evenly, put the stained gypsum mold in it and soak it for about 3-10 minutes, then clean it with water 2-5 times, dry it after washing, and sprinkle chalk powder on it to restore the color.

3. If the plaster mold is covered with oil, put the mold in 1000ml soapy water, soak it for about 20 minutes, and then clean it with water. If some stubborn stains cannot be removed, you should use some dye and apply it to the plaster, and it is best to choose a copper-like color, which will look better.

Article summary: Well, how to solve the yellowing of the gypsum line and what is the reason for the yellowing of the gypsum line is introduced here, if you need more information, please continue to pay attention to Qeeka Home, and we will have better and more exciting content for you in the future.

Do the math how much it will cost you to renovate your home

How to remove the cement on the gypsum line, hello, the method has two remaining key cracks and vertical closure; First, clean it with dilute hydrochloric acid or dilute sulfuric acid used in the laboratory of the cement plant! Because cement is alkaline, it melts or dissolves when exposed to acid. However, strong acids can damage the ground where the cement has solidified.

Second, bright objects are cleaned with cement cleaning agent. Generally, cement cleaning agent is composed of compound acid, resist and descaling accelerator, which can quickly and thoroughly dissociate the accumulation of cement scale, rust scars and other minerals, so that the sediment and the sediment in the cement scale are washed away together. Generally, the cement cleaner needs to be diluted before use.

However, cement cleaners are acidic, so be careful not to contact them for a long time**. I hope my answer is helpful to you, and finally I wish you good health and a happy mood again! <>