As soon as my wireless router is connected to the cat, the red light flashes

Two can be used at the same time,If you say,The network port light flashes is normal only data transmission,The signal light will flash,The network speed is slow,You check if there are other IP addresses to use,By cracking the software,Directly steal the router password,Then you can directly steal your network speed through wireless,Generally, two computers use a network end,The network speed is not much slower,At best,Two computers watch TV with a little bit of card,That's a small thing,But it won't say that it's a lot slower。

The suggestion is as follows: check the connector on the ** line and restart the router to see if the problem still exists.

Cancel the automatic login function of the router, set the dial-up with the computer, see if you can log in normally, or what is the error message returned by not logging in, and look for the answer to the question by the error returned.

Whether the routing cat is damaged, use the replacement method, and try to change it to a normal one.

Call ** to customer service for consultation or repair.

According to your description: first of all, you need to judge the situation when the broadband connection is dropped, and according to different appearances, you can really find the real cause of the disconnection. The following is a targeted solution according to various disconnection phenomena:

1) A small red cross appears in the lower right corner of the computer when the connection is disconnected. Suggested solutions: It may be caused by poor network cable contact, network card hardware failure, or abnormal power supply of network equipment such as ADSL modem, and it is necessary to fix the network cable, equipment power supply or replace the network cable.

2) A small yellow exclamation mark appears in the lower right corner of the computer when the connection is disconnected, and it is suggested that the solution may be caused by poor network cable contact, network card hardware failure, or abnormal power supply of network equipment such as ADSL modem, check whether the ADSL modem status light is normal, and replace the network cable, restore the initial settings of ADSL, etc.

Telecom price reduction, mobile phone bill is only 3% off! 49 yuan package 129 yuan, including 330 minutes of voice, 600m traffic, and you can add 1 yuan to double the traffic! 69 yuan for 189 yuan; 89 yuan for 289 yuan; 99 yuan for 329 yuan.

For more information, please visit the online business hall of Anhui Telecom.

Have a great day! Hope mine is helpful to you and can get yours!

Which red light flashes? If the LOS indicator (some optical modems write the "optical signal" indicator) flashes red, it is generally the optical fiber is broken, please contact the operator for maintenance, this cannot be solved by yourself.

Is it that the IP of the router and the cat are both in the same network segment causing a conflict.

Set the router separately to set the IP of the router to an IP that is not commonly used, for example.

There are several scenarios:

1. There is a problem with the optical interface of the optical modem, and the optical modem needs to be replaced. (This is rare).

2. The indoor pigtail connection optical cat connector is loose. Plug the connector in and it can be restored.

3. The bending of the indoor part of the optical fiber is too large. Excessive bending of the optical fiber will affect the total reflection transmission of the optical signal in the optical fiber, as long as the optical fiber is straightened.

The green light of the telecom optical modem network G keeps flashing, and it can't be connected to the network Originally, the router was used, but I don't know if there was a problem with the router, and the technician who came to repair it turned on the wireless function of the optical modem and used it as a wireless router. The family opened a grocery store downstairs, because they didn't use the router, they directly connected the network cable from the store to the router, and the mobile phone and laptop at home used the wireless Internet access of the light cat. It was fine last night.,Suddenly the green light of the light cat's network G began to flash.,And then I can't get on the Internet.,How to deal with it?

You turn off the power of the optical modem and then turn it on.

Summary. The indicator of the router has an optical signal, which means that this is a PON device that combines the optical modem and the router, and the light signal flashing red may be due to the following reasons:

1. The light port of the computer room emits low or no light, causing the user's optical modem to work abnormally, and the optical signal light cannot receive the optical signal sent from the optical cable or the power of the optical signal is too low, which will cause the optical modem to shake hands with the computer room abnormally, and the optical signal will flash or alarm with a red light.

The router shows that it is offline, and the cat signal light keeps flashing red light.

The indicator light of the router has an optical signal indicates that this is a PON device that combines the optical modem and the router, and the reason why the optical signal flashes red may be due to the following reasons: 1. The optical port of the computer room emits low or no light, causing the user's optical modem to work abnormally.

2. If the optical cable fails to remove the stool (including the broken optical splitter), it will also cause the light to be unable to receive or the light is too low, and the light signal light will also flash or red light warning; 3. The failure of the Yuwei optical cat itself, and the partial damage of the light collector will also cause this phenomenon;

4. If the server fails, such as the maintenance of the imitation town songr of the Beizheng service, it will cause a red light. No matter which of the above four situations appears, users basically can't solve it, and they can only report the problem.

You can check the solution based on these few notes.

The router 2G5G light keeps flashing, and the cat signal light keeps flashing red.

The phone router shows offline.

According to the situation you explained, there are several ways above and you said, you can troubleshoot and solve them.

Summary. If the optical signal light turns red or flashes, it means that the optical fiber signal cannot be received, which is usually caused by the following conditions:

1.If there is a problem with the optical interface of the optical modem, you need to replace the optical modem. 2.The indoor pigtail connection optical modem connector is loose, and the connector can be restored by plugging it in; 3.

The bend of the optical fiber in the indoor part is too large. Excessive bending of the optical fiber will affect the total reflection transmission of the optical signal in the optical fiber, as long as the optical fiber is straightened. 4.If the outdoor optical fiber is broken or the optical port of the equipment in the equipment room is faulty, you need to contact the staff to report the fault.

Can you elaborate on that a little bit more?

If the optical signal light turns red or flashes, it means that the optical fiber signal cannot be received, which is usually caused by the following conditions: If the optical signal light turns red or flashes, it means that the optical fiber signal of the Zen banquet cannot be received, which is usually due to the existence of the following situations: 1

If there is a problem with the optical interface of the optical modem, you need to replace the optical modem. 2.The indoor pigtail connection optical modem connector is loose, and the return excitation head can be plugged in to recover; 3.The bend of the optical fiber in the indoor part is too large.

Excessive bending of the optical fiber will affect the total reflection transmission of the optical signal in the optical fiber, as long as the optical fiber is straightened. 4.If the outdoor optical fiber is broken or the optical port of the equipment in the equipment room is faulty, you need to contact the staff to report the fault.

Summary. 3. The bending of the indoor part of the optical fiber is too large. Excessive bending of the optical fiber will affect the total reflection transmission of the optical signal in the optical fiber, as long as the optical fiber is straightened.

The wireless cat-light signal flashes red.

Hello dear! We're happy to answer for you! The reasons why the wireless caton signal flashes red are as follows:

1. There is a problem with the optical interface of the optical modem, and the optical modem needs to be replaced.

2. The indoor pigtail connection optical cat connector is loose, and the connector can be restored by plugging it in;

3. The bending of the indoor part of the optical fiber is too large. Excessive bending of the optical fiber will affect the total reflection transmission of the optical signal in the optical fiber, as long as the optical fiber is straightened.

4. If the optical fiber of the outdoor part is broken or the optical port of the equipment in the computer room is faulty, it is necessary to report the broadband fault, and there will be staff to come to the door to troubleshoot the fault after the fault report.