How to set up WIFI Internet access on Tenda W311R wireless router?

Here's how to set up your router:

1. Line connection:

a.Connect the network cable from the cat to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1, 2, 3, 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable connected to the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet (when you are not connected to the router), you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP Mode", and enter your fixed IP address, subnet mask, gateway, DNS domain name server and other parameters correctly.

4. After setting, click "Advanced Settings" - "System Status" to check whether the connection status of the WAN port shows that it is connected, and whether the corresponding connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

**The following is how to set it up

Hello landlord! This is how it is set, but you need to set the IP acquisition to "automatic acquisition" in the advanced settings. As for wireless encryption, your password is too simple, it is recommended to change to a key with a combination of English and numbers!

Computer: 1. Connect A301 to the power supply, and connect the computer and A301 with a network cable at the same time, (the desktop computer is only connected to the A301 with a network cable, not a router and other equipment; Disconnect the laptop from the wireless connection, or connect to the WiFi signal of the A301) Open the browser, enter **:, press Enter, and enter the login interface.

2. Enter the password: admin, click OK to enter the setting interface.

4. In the pop-up prompt box, click "OK", the device will automatically restart, and you can verify whether you can surf the Internet after restarting.

Verification method: Verify that the setup is complete:

1. The lights on the left, upper and right sides of the A301 indicator are always on.

Check the original WiFi signal strength, the signal strength means that the setting is complete.

Note: If the status light is flashing and cannot access the Internet, you must check whether there is any error in the settings and check carefully.

Mobile phone: 1. Connect the extender to the power supply.

3.Open the browser of your mobile phone, enter **: enter, enter admin and click OK.

4. Enter the settings interface, click "Turn on Scan" in the judgment, select the enlarged wifi name, enter the password, and click Save.

5. After clicking "Save", in the pop-up prompt box, click "OK", the device will automatically restart, and verify whether the Internet can be accessed after the device is restarted.

Verification method: Verify that the setup is complete:

1. The lights on the left, upper and right sides of the A301 indicator are always on.

Check the original WiFi signal strength, the signal strength means that the setting is complete.

Note: If the status light is flashing and cannot access the Internet, you must check whether there is any error in the settings and check carefully.

Frequently asked questions. 1. Can't enter the settings interface on my phone?

Answer: Please turn off the mobile data first, make sure the mobile phone is only connected to the WiFi signal of the A301, and then try to enter the settings interface.

2. Why can't I find the signal of the previous A301 after setting?

Answer: After the A301 is set, the WiFi name and password will automatically remain the same as the WiFi name and password of the original router, so you can only search for the WiFi signal of the original router.