How to set up the Mercury MW313R wireless router

Dear users, hello.

Hope the following can be helpful to you:

1.Plug the broadband modem or home network cable into the WLAN port of the router, and then connect to the computer through the network cable or wireless network.

3.After entering the page, you will be prompted to enter management, which also needs to be found in the manual, and the general password is admin.

4.Click the Setup Wizard, follow the prompts on the page to set up broadband without PPPOE dialing, and enter the broadband password.

5.According to the prompts on the page, check the box to turn on the WiFi network, and set the password, when finished, click Next, and the device will automatically restart.

Anhui Telecom will serve you wholeheartedly.

Here's how to set up the Mercury router:

2. Then open the browser of the computer, enter the login address and login password of the router, and the specific login IP and password can be looked at the label on the back of the router.

3. After entering the router, there will be a setup wizard, first fill in your broadband account and password.

4. Then set the wireless name and connection password.

5. After the successful setting, a prompt will appear for the successful setting, and it will take effect by restarting the router.

The steps to set up the Mercury MW313R router are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, open the browser and enter: press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be in the back of the router, in general: account name:

admin password: admin.

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system. 7. Click Done, restart the router, and the settings have been successful.

As long as the router is connected to the power supply, it can be connected normally. First of all, make sure that the broadband account password is correct, and secondly, the network cable connection. The incoming cable is connected to the WAN port of the router, and then the LAN port is connected to the computer. Generally fine.

Are you connected to broadband? WLAN port look.

Here's how to set up your wireless router:

1. Power on the wireless router first, connect the computer or mobile phone to the wireless router, enter the router, network parameters, LAN port settings, and change the LAN port address to avoid conflicts with the LAN port address of the cat;

2. Connect the network cable from the LAN port of the cat to the WAN port of the wireless router

3. Open the browser, enter the login address of the wireless router: , enter, enter the management user name: admin, password: admin (the login address, management user name and password of different brands of wireless routers are different, you can refer to the manual), confirm;

4. After entering the wireless router, set up the wizard, next, select the PPPOE dialing method, next, enter the Internet access and password, next;

5. Set the wireless network name under the SSID, set at least 8 digits of the wireless network password under the PSK, and tell the stalk of the next chicken class;

6. Save, restart the wireless router according to the prompts to complete the installation of the wireless router.

Configuration steps (factory reset of router is recommended):

The WAN port of the router is connected to the network cable of the broadband modem.

The LAN port of the router is connected to computers, TVs, and set-top boxes.

Assuming that the cat does not have a router, the new router should be set to "PPPOE dialing", use the account number and password given when handling broadband, and pay attention to distinguishing between "uppercase and lowercase letters".

The local connection of the computer is set to "Automatically obtain IP address, automatically obtain DNS server address".

The computer can no longer dial up, and if there is a broadband connection, be sure to disable it.

Here's how to set up the Mercury MW313R router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

See what you need! Generally, the bus is connected to the WAN port, the LAN port is connected to the computer, and the computer IE input is generally this address by default), enter the user and password on the router nameplate, enter the router background, set up the wizard, and follow the prompts step by step. It's simple.

Mercury MW313R is an ordinary router, the network cable connects the router LAN port and the network card; Use a computer browser, log in to the router settings page, run the setup wizard to complete the setup step by step, and the login information is printed on the sticker on the back of the router; Feel free to ask!