What s wrong with the sinking of the barrel in the automatic washing machine?

That's the washing machine drum.

The bearings on the spindle were broken, causing the fully automatic washing machine drum to sink. Solution: First of all, use a wooden square to support the sinking drum of the washing machine, and fix the drum well, so that the drum cannot shake.

Then remove the large pulley of the drum from the back of the washing machine; Then remove the bearing seat of the washing machine, and then remove the inner circle (inner sleeve) of the bearing on the main shaft of the washing machine. Carefully check whether the washing machine drum spindle and the body water seal kit of the washing machine are damaged or leaking, and if damaged, they can be replaced; replacement of damaged bearings; After filling with grease. Replace the bearing seat of the washing machine, the large pulley of the drum, and the accessories in turn.

It depends on whether you are a roller or a fully automatic roller, generally the roller will not drop things, if it is a roller, it depends on where you are falling, whether it is an inner barrel or an outer barrel or under the roller, if it is under the roller, it may occur winding reducer.

Shaft and water leakage or washing abnormal, you can solve it yourself, you can remove a screw in the center of the wave wheel, add half a bucket of water in the bucket, generally the wave wheel will float up by itself, if you can't float, you can find two hard about 20cm iron wire or steel wire bent on a hook from both sides of the wave wheel hook up and lift it up, what is below at a glance, you can also easily take it out; If it falls into the outer cylinder, it doesn't matter, you can also leave it alone, if you want to make a decision, it's simple, you can lie down the washing machine from the bottom of the washing machine can be seen and can take out the things that fell in, but generally there may be an anti-rat net at the bottom of the washing machine, which is inserted at the bottom, you can remove one or two grain screws and pull him out to solve the problem.

When the weight of clothes and water reaches a certain level, the boom spring will sink due to gravity, and the washing program can run normally.

1. Due to the automatic washing machine barrel, the four-point suspension spring damping and damping mechanism is adopted;

2. In the process of laundry, clothes and water are put into the bucket, and the spring will move downward due to the change of weight;

3. This situation is normal, and it will be restored after the laundry is finished and drained.

Precautions for the use of washing machines.

1. Install the washing machine in a flat place, away from heat sources, avoid direct sunlight, and avoid placing the washing machine on a carpeted floor.

2. After the installation is completed, check whether the ground is stable, and if there is shaking, adjust the feet until it is stable.

3. The washing machine that is often used is actually easy to hide dirt and dirt, there is a bucket on the outside of the washing machine, and the laundry water will flow back and forth between the two buckets when the washing machine is working, and if the drainage is not complete, the humid environment in the washing machine will breed various bacteria and molds, and the washing machine will produce peculiar smells.

4. Before washing clothes, check whether there are any foreign objects in the pockets of clothes, such as coins, mobile phones, bank cards, wallets and tissues. If it is not taken out during cleaning, it will not only cause unnecessary losses, but also have the possibility of damaging clothes, especially metal foreign objects such as keys, and scratching the inner cylinder parts of the washing machine.

Summary. It is caused by the displacement or breaking of the three springs that support the inner barrel in the washing machine. The inner cylinder of the wave turbine is supported by four booms, with air damping boom and spring boom, no matter what kind of boom is elastic, the inner cylinder will naturally sink 5-10 cm after putting in clothes and water, and the inner cylinder will float up again after washing and emptying.

It is caused by the displacement or breaking of the three springs that support the inner barrel in the washing machine. The inner cylinder of the wave turbine is supported by four booms, with air damping boom and spring boom, no matter which regret touching and planting the blue trace boom is elastic, the inner cylinder will naturally sink 5-10 cm after putting in clothes and water, and the inner cylinder will float up after the clothes are washed and emptied.

With maintenance. This is normal and will resume when the laundry is finished and drained.

Don't worry.

Thank you. You're welcome.

1.If the brake is not loosened, remove the rear cover and open the door cover of the dry barrel, observe whether the brake will correspond to the action and release, if the brake is not loosened, check whether the cable connected with the door cover is too loose or disconnected, adjust or connect the cable, so that the brake can be loosened when the door cover is opened.

2.Excluding the reason that the brake is not loosened and the motor is damaged, it may be that the motor rotates freely when opening the door cover, and the power is still not turning, and the problem is that the door cover safety switch is in poor contact or there is a phenomenon of rat biting the broken wire (after disassembling the washing machine, the upper three screws and opening the operation panel cover to check, and shorting the two wires of the door cover switch to test the machine).

3.The washing machine spins off the barrel slowly, and the weakness is generally caused by the change or failure of the capacitor. Try to change to the same capacitor, but remember that the capacity of the capacitor should not exceed the original value, if it is too large, it is easy to heat up the motor, or even burn out, and if it is too small, the speed is not enough.

In addition, if the line has a broken circuit, there will also be this problem, at this time, the capacitor does not work, it is better to check whether the line and capacitor are in good condition, if it is confirmed that the capacitor is broken, and then buy a capacitor to replace it, so as not to waste.

4.Excluding the reason why the brake is not loosened, it is still difficult to rotate the motor coupling because of the lack of oil, damage or burning of the windings of the motor bearing (it is recommended to find a professional repairer).

5.If it does not turn, it is suspected that the capacitor of the motor is variable and the capacity is insufficient, and the capacitor test machine of the same specification should be replaced, which should solve the problem.

There are many reasons, first of all, check whether the brake is locked and not loosened, resulting in the motor not operating normally. It should be adjusted to open and close the brake freely.

If there is no problem with the brake, it can be repaired according to the following methods:

There are many reasons why the motor does not work, first of all, turn the motor shaft by hand without power, and see if the rotation is flexible? If there is resistance to rotation, it means that the motor bearing is seriously worn or the lubricating oil is dry, and the new bearing should be replaced or lubricated to make it rotate flexibly without resistance. When installing the fixed motor, it is necessary to tighten the screws diagonally, and it must be tightened gradually, not in one step, and at the same time, it is necessary to hit the shaft back and forth with a wooden handle driver to ensure that the shaft is concentric with the bearings at both ends, so that the rotation will be flexible and without resistance after fastening.

If it turns flexibly without resistance, there are several reasons:

First, the capacitance capacity decreases, and a new capacitor of the same capacity should be replaced.

The second is that there is an inter-turn short-circuit fault in the coil, and the resistance value of the running winding and the starting winding can be measured with a multimeter to judge the quality of the winding. If the resistance value is abnormal, it is necessary to replace the motor with a new one.

It may be that the bearing is short of oil, you can take it apart and take a look, and add some if there is no oil.

The washing machine should also be cleaned regularly, otherwise there will be a certain amount of dirt in it that will affect its operation after a long time.

There may be several reasons for the sinking of the barrel in the fully automatic laundry rock roller machine:

Unstable center of gravity: If clothes or other items are not evenly positioned inside the washing machine, it can cause the center of gravity of the washing machine to become unstable, causing the bucket to sink. Try reassigning the laundry so that it's evenly distributed in the bucket.

Broken suspension springs: The bucket in the washing machine is usually connected to the body by the suspension spring, and if the spring is broken or loose, it will also cause the bucket to sink. Suspension springs need to be replaced or repaired.

Aging of shock absorbing pads: Washing machines need to use shock absorbing pads to cushion vibrations when running, and if the shock absorbing pads are aging, it will also cause the inner barrel to sink. The aftershock pads need to be replaced.

Deformation of the body: When the washing machine is used for a long time or is hit by external forces, the body may be deformed, causing the inner barrel to sink. Airframe parts need to be replaced or repaired.

In short, if you find that the barrel in the automatic washing machine is sinking, you need to check the cause in time and repair or replace it accordingly. It is advisable to seek the help of professional maintenance personnel to ensure safety and repair effectiveness.

What is the problem with the sinking of the barrel and fiber in the automatic potato scale laundry shed? Hello dear, the sinking of the barrel in the automatic washing machine is not a problem, it is normal. Due to the fully automatic washing machine barrel, a four-point suspension spring damping and damping mechanism is adopted; During the laundry process, the bucket is filled with clothes and water, and the spring will move downward due to the change in weight; This situation is normal, and it will be restored after the laundry is drained, and there is no problem. Hope it helps!

When the weight of clothes and water reaches a certain level, the boom spring will sink due to gravity, and the normal operation can be resumed after the washing program is over.

1. Due to the automatic washing machine barrel, the four-point suspension spring damping and damping mechanism is adopted;

2. In the process of laundry, clothes and water are put into the bucket, and the spring will move downward due to the change of weight;

3. This situation is normal, and it will be restored after the laundry is finished and drained.

When the automatic washing machine is drained, the weight of the bucket is reduced because the water of the bucket is discharged out of the barrel, and the spring in the damping cylinder lifts the bucket upwards under the action of the spring's own elasticity due to the reduced force, so when draining, you will see that the inner barrel rises again and is trapped.