The Tengda 311 and D Link605 wireless routers bridge 5

Two wireless routers set up bridging steps:

1.Modify the IP address of the LAN port.

Set the LAN port addresses of the two wireless routers to different IP addresses of the same network segment, if the LAN port address of the higher-level wireless router is, you can set the LAN port IP address of the wireless router to the last value can be 2 254).

2.Set the SSID, encryption mode, wireless password, and channel of the two wireless routers to be the same.

3.Set up a higher-level wireless router.

1) Go to the wireless extension interface of the wireless settings, select WDS in the wireless extension mode, and click to start scanning.

2) Find the SSID of the wireless router in the pop-up dialog box, and then click to connect.

3) In the key, enter the wireless wifi password of this router.

4: Set up a lower-level wireless router.

1) Log in to the wireless router settings interface, refer to step 3, and add the upper wireless signal;

2) Disable the DHCP function of this wireless router.

5.After the setting is complete, check the IP address obtained by the computer, when the address of the "default gateway" is the IP address of the LAN port of the higher-level wireless router (in this case, the device can access the Internet.

The bridge compatibility between different brands is poor, and the wireless may not be able to set up encryption.

Go to the D-Link605 router, configure the LAN port and the other router in one segment but with different IPs. Then turn on the wireless function, turn on the bridge, and write an SSID number. Select the encryption mode.

Hello, first of all, take a look at the following articles:

1.Both wireless routers need to have bridging capabilities.

2.The wireless name and SSID used by the wireless router must be the same.

3.The wireless channel used by the wireless route must be the same.

4.Both routes have bridging mode WDS enabled, and the MAC addresses of each other's routes are filled in with each other.

5.The wireless encryption mode and password of the wireless route must be the same.

6.It is best to use wireless router products from the same manufacturer, or even the same model, to avoid compatibility problems.

If you still don't know how to set it up, you can contact technical support.

Change the wireless mode, channel, SSID, encryption mode, and wireless password of D-Link 605 and 311R to be consistent.

The DHCP of the D-link605 is turned off, the LAN port IP is changed to the DHCP of the 311R, the LAN port IP is changed to the D-link605, and the WDS is turned on.

This setup allows auto-roaming between the two routes.

First of all, make sure that the first router can access the Internet normally: Step 1: The first route gateway SSID is set to 111, and then only the Internet can be set to wireless settings Basic settings:

Network Mode 11BGN Mixed Mode Channel 6 Wireless Security Settings "Security Mode WPA-Personal Encryption Rules AES Password 12345678 Step 2: Second Router Go to the settings page Change the gateway to Select the mode at the beginning of the R of the WDS settings Enter the password when scanning the 111 connection 123456789 Pay attention to the encryption rule mode, turn off the DHCP wireless settings, basic settings Network mode, 11BGN mixed mode, channel 6, wireless security settings, "Safe Mode, WPA-Personal Encryption rules AES password 12345678》 The first one should also select the mode at the beginning of the R set by WDS Scan the second route, the default SSID is 222 Enter the password when connecting 123456789 Pay attention to the encryption rule pattern to be consistent Step 3: Local connection of the second router Disable and re-enable Find another computer to connect to the second router If you can enter the settings page of the first router, the bridging is successful.

Generally, it is recommended that the bridging product is the same as the chip, if the chip is different, it is recommended to bridge without encryption first, and then use WEP or OPEN devices with strong encryption compatibility for bridging.

In the network era, the router is a bridge between computer networks, but in the process of connecting the network to the network, the configuration of the router plays a key role, and the router equipment produced by Tengda is extremely cost-effective, so do you know how to bridge the Tengda W316R router? Here are some relevant information about Tengda W316R router bridging that I have compiled for your reference.

How to bridge the Tengda W316R router:

WDS function setting network topology diagram: (W311R and W316R are connected to one computer each for testing).

W311R is Lazy modem modem, W316R is repeater mode, (the wireless security trembling setting security mode of the two routers cannot be encrypted, and the encryption situation cannot be bridged).

W311RSelect Lazy Mode For the TENDA wireless routerIn this mode, the peer router must be in Bridge mode or repeater mode, click Save after selection, then W311R will restart, and W311R will be set successfully.

For the W316R, you need to set the LAN port of the router before WDS, and the LAN port address must be in the same network segment as the LAN port IP of the W311R.

W316R, enter the router settings interface, wireless settings - wireless basic settings - select bridge mode.

For the W316R, the broadcast channel and expansion need to be consistent with the channel of the W311R's wireless basic settings.

The default WDS working mode of W316R is only Repeater mode, click to turn on scanning.

W316R, select the corresponding SSID of W311R, click OK in the pop-up dialog box, and click OK under the click page.

W316R, you need to turn off the DHCP of W316R, and click OK.

Test whether the WDS is successful.

Connect the W316R's SSID W316R wirelessly on another computer

Connect successfully and get the IP address assigned by the W311R router.

Check whether you can ping the gateway and the external network, and WDS is successful.

2. WAN (Wide Area Network) port setting: PPPoE dial-up, enter broadband and password.

3. LAN port setting: keep the default one.

4. Wireless settings: wireless mode selected as WDS+AP+Router mode SSID wireless name custom (generally not supported Chinese), channel: (choose any one general signal interference is small), turn on the wireless function, turn on the SSID broadcast function (so that the wireless device can search for this wireless disturbance Zhengshu Road), wireless security settings:

Generally, use WPA-PSK WPA2-PSK, set a password (at least 8 digits), 5. MAC address: You need to fill in the MAC address of the secondary router (you can check the MAC address on the label at the bottom of the device).

7. After saving the configuration, check the running status of the router and whether the parameters take effect.

9. WAN port setting: no need to set up.

10. LAN port settings: modify the default one, (generally you need to restart the router, and then you need to use Cong guess to log in, and the modification is to prevent the IP conflict between the two routers).

11. Wireless settings: Select WDS+AP mode, set the wireless name, channel, encryption method, and password to be exactly the same as the main router, and fill in the MAC address of the main router in the MAC address column (MAC address can be viewed on the label at the bottom of the device).

12. The DHCP server of the secondary router needs to be shut down, and you can save it!

A TP wireless router can be bridged with a 311R wireless WDS trunk. Specific steps:

1.First of all, set up the TP-Link wireless router, set the wireless router to the web type, and ensure that it can access the Internet after setting.

2.Set w311r:

1) Set the router's wireless security mode to WEP. Due to the use of WEP encryption, this is easy to be cracked wirelessly, so it should be limited by the MAC policy in the wireless connection.

2) Go to the WDS settings page and select the WDS mode as Repeater Mode. Encrypt select WEP and finally fill in the wireless MAC of the TP router. If you don't know, you can click to turn on the scan first, and you can find the SSID and MAC of the TP router in tens of seconds.

Confirm the connection. 3) Turn off the DHCP service. Finally, save the settings and restart the router and it's OK.

Referring to this, in fact, there is too much information about wireless bridging on the Internet. Similar. Instead of us copying and pasting here and seeing you dizzy, it's better to search for it yourself, hehe.

Tengda N3 set wireless bridging method:

Primary Router Settings].

1. Enter the settings interface of the main router, then click [Running Status] in the left option bar, and you can find the DNS server in the WAN port status bar, there are two in total, the primary DNS and the alternative DNS server, record them.

2. Click [Network Parameters] - LAN Port Settings] to set the LAN address of the router to save, at this time, it will be restarted and then return to the settings interface and click [Wireless Settings] - Basic Settings.

3. Set the SSID to TP Link A. Set the wireless channel to: 11. Note: The WDS or Bridge feature must be turned off.

4. Click [Wireless Settings] - Wireless Security Settings, and select WPA-PSK as the encryption method, in this example, 12345678 as an example. Note: WPA WPA2 encryption is more secure and more stable to bridge than the old WE encryption, so WPA WPA2 encryption is recommended.

5. Click [DHCP Server] -- DHC Server Settings] and set [Address Pool Start Address] to; Set the End Address of the Address Pool to Click Save to restart the main router. The main router is set up.

Set up the secondary router].

1. Enter the settings interface of the secondary router.

2. Click [Network Parameters] --LAN Port Settings.

3. Set the LAN address of the secondary router to prevent conflicts with the main router, and it is also convenient to manage the main and secondary routers.

4. Click [Wireless Settings] - Basic Settings.

5. Set the SSID to TP Link-B. Set the wireless channel to: 11.

6. Check [Turn on WDS], click Scan in the pop-up interface, find the SSID of the main router after getting the AP list, that is, TP Link A, click the [Connect] button on the right, select WPA-PSK as the encryption method, fill in the key of the main route: 12345678, (keep it consistent with the main router), and click Save.

7. Because the new WDS function is different from the old bridge and more advanced, you only need to turn on WDS on all secondary routers and fill in the information of the main router, if the main router turns on the WDS or bridge function, please turn it off, otherwise the WDS function cannot be used.

8. Click [Wireless Settings] -- Wireless Security Settings to set the password of the secondary route wireless.

9. Click [DHCP Server] -- DHCP Server Settings], change [Address Pool Start Address] to [Address Pool Start Address] to [Address Pool Start Address]. [Gateway] Fill in the IP address of the main router, that is. The primary and alternate DNS servers fill in the previously recorded addresses and save and restart the router.

10. The setting is complete and the connection is successful.

To set the same wireless name, channel, encryption method and password, and then fill in the MAC address of each other, it is recommended to use the same product for wireless bridging.

No problem.

No matter what model of router you use, switch mode settings:

1. First, set the router to switch mode, which can be obtained either statically or dynamically.

2. Take a static IP address as an example: select a static IP address.

WAN port settings:

IP - Setting: It needs to be the same network segment as the router on the first floorx can be any number from 2-254).

Subnet mask –

LAN port settings: You can choose that x cannot be the 1st floor router segment 1, and y can be any number from 1 to 254.

DHCP: On (Provides automatic IP assignment for downstream PCs).

Wireless settings: Turn on the wireless function, select the protocol mode, and set encryption.

Note: If you are using an Apple mobile phone to surf the Internet, you must select the protocol or compatibility mode, and other terminal devices do not support a b g mode. ）

SSID setting: This is the name of your router's wifi.

It is possible not to broadcast, no one can see this wifi signal, but you must remember it yourself).

Login password: Change the login account and password of the router.

When you're done, save the settings.

3. Plug the network cable from the first floor into the WAN port of the wireless router on the fourth floor.

4. The machine can be connected to the LAN port of the router on the 4th floor with a network cable.