How to set up a Mercury wireless router laptop wirelessly connected to a second computer

There are two ways to solve the cascading problem of routers:

1.Change the connection mode of the second-level router, connect the network cable connected to the LAN port of the first-level router and also connect to the LAN interface of the second-level router, at this time the second-level router is used as a switch, there is no need to set the WAN interface parameters, directly connect the network cable to the computer, just log in to set the wireless part of the parameters can be used, the wireless terminal searches for the wireless signal of the wireless router and enters the encryption key, and can be connected and used after verification;

2.Another way is to use the WAN interface of the second-level router, at this time the router is working in the routing mode, connect the computer with a network cable to log in to the second-level router, set the second-level router WAN interface to dynamic IP mode or static IP mode (the static IP address needs to be set according to the login IP address of the first-level router), and then set the parameters of the wireless part. However, it should be noted that the IP address assigned by the LAN of the second-level router must not be in the same network segment as the first-level router, otherwise there will definitely be conflicts;

3.In general, in the case of cascading multi-level routers, the first-level router needs to be set to the route mode, that is, after logging in, enter the WAN interface setting -PPPoe mode, and enter your broadband and password.

If the notebook is directly connected wirelessly, the desktop needs a network cable with double crystal heads, one section is connected to the router, and the other end is connected to the host, which is changed to automatic acquisition in the network attribute Internet protocol.

Mercury wireless router.

Mercury Wireless Router Connect to Another Router Steps:

There are 2 ways to set the WAN port: 1. The second router WAN port is set to dynamic IP; 2. Use the second router as a switch. For the convenience of illustration, here is a brief introduction to the setting environment, the first router has been set up successfully, you can connect to the Internet to surf the Internet; The second router is connected to the LAN interface of the first router with a network cable).

All settings are done on the second router, and there is no need to make any changes on the first router.

Method 1: Set the second router's WAN port to a dynamic IP address

Prepare two network cables, one end of which is connected to any LAN (1, 2, 3, 4) interface on the first router, and the other end of the network cable is connected to the WAN interface of the second router. Connect one end of the network cable to any LAN (1 2 3 4) on the second router, and connect the other end to the computer.

Type in your browser and press enter – > enter your login username.

Log in with your password to enter the settings screen of the second router.

Click "Network Parameters" - WAN Port Settings "- WAN Port Connection Type" to select: dynamic IP (called "Auto Acquisition" and "DHCP" on some routers) - click "Save".

Click "Network Parameters" - LAN port to set Wang Oak "- IP address on the right".

Modified to: > click "Save", and then you will be prompted to restart the router.

Tips: After the second router is restarted, the user needs to log in to the settings interface of the wireless router, that is, the IP address of the router LAN interface, which is the setting of the Wuzha line router**.

Method 2: Use the second router as a switch.

Connect the computer to any of the LAN (1, 2, 3, 4) ports on the second wireless router with a network cable; Note: The second router cannot be connected to the first router with a network cable temporarily.

If the settings of the first router are, then the LAN port IP of the second router is modified to Warm Reminder: After the LAN port IP is modified, the router may be prompted to restart, and after restarting, you need to enter the changed IP address in the router to log in to the settings interface, such as or.

Prepare another network cable, one end is connected to the LAN (1 2 3 4) interface of the first router, and the other end is connected to the LAN (1 2 3 4) interface of the second router.

Shut down the DHCP server on the second router.

Click "DHCP Server" - DHCP Service - DHCP Server "Select: Do Not Enable - > click "Save".

After completing the 4 steps of appeal, the second router can access the Internet, if you want to use the wireless wifi on the two routers, you only need to set the wireless wifi name and password on the second router, and you don't need to go through other settings.

The router needs to be set up in the background of the router to connect to other routes

1.Use a computer to connect your own router to the background management page (how to enter the router background manual has an introduction), your router should be entered into the settings, and the IP address of the secondary LAN port is different from the IP address of the main router. Disable DHCP and save the restart.

Further reading: Attention to the problem:

1) The connection principle of the router: the computer can only be connected to any one of the LAN ports of the router, which is a prerequisite for entering the settings interface. Moden (moden), optical modem, or home network cable can only be connected to the WAN port of the router, which is a prerequisite for the router to be able to access the Internet.

2) After the installation of the Mercury router is completed in accordance with the appeal, the computer will not be able to access the Internet temporarily, and when the Mercury router completes the Internet setting, the computer will automatically be able to access the Internet, and it is no longer necessary to use the "broadband connection" on the computer to dial up the Internet.

3) In addition, when setting up the router, you don't need a computer to be able to access the Internet, just connect the computer to the LAN port of the router with a network cable. Many novice users often ask me, how can I set up a router when my computer has no network? Please don't ask such questions again.

4) After the Mercury wireless router is successfully installed, the SYS indicator on the device will flash, the WAN interface will be solid or flashing, and the port connected to the computer in port 1 2 3 4 will be solid or flashing.

For the second Mercury router, follow these steps to connect and set up wireless

1. First, look at a global map, and b is the second route.

2. Connect router B to the computer separately to set it, don't connect the WAN port of B first, and only use LAN to connect to the computer.

3. Open the management interface of router B in the browser and change the IP address of the LAN port of route B.

4. Turn off the DHCP function of route B.

5. The connection method of the AB router, after B is set, the WAN port of B is idle (or not).

6. If B is a wireless router, set it as usual, and finally the LAN port of B is successfully connected to the LAN port of A.

Note: 1. The IP addresses of the two routes cannot be the same.

2. DHCP cannot be turned on for the second route

3. The third and fourth steps cannot be reversed.

Turn on the wireless function, turn off DHCP, and no network cable of the second router can be plugged into the WAN port, but can be plugged into any of the 1234 ports.

Whether it's a cat or a network cable, the network cable that comes out of the home is plugged into the WAN port, the PC connects a line to the LAN port, enters the routing IP, enters the settings page, finds the setup wizard, and the next step is to select the PPPoE mode, and the next step is to enter your adsl account password, save and then find the wireless settings, turn on the wireless, wireless broadcasting, and set an encryption password (you can not set it, but someone may steal the network) Save and exit It should be OK.

I also use the Mercury router, which is actually quite easy to get. Isn't there several network cable sockets on the router? Find the wan socket, plug the cat on top of it, and the rest will be similar to the cat.

Are you sure your router is set up? It's LAN connected to the computer.,And then set the network neighbor-attribute-local connection-attribute-protocol-select automatic--okClose the router without a broadband connection.,It's an automatic connection in the future?

1. The router port usually consists of one W port + 4 L ports.

2. Set up the router, if there is wired Internet access, you can pull out four network cables from the L port for 4 computers to access the Internet.

3. If it is wireless, the IP address pool is from 1 to 99, which can be used for 99 wireless devices to access the Internet.

If the Mercury wireless network card appears.

If you are connected but cannot connect to the Internet, you can troubleshoot the problem by taking the following steps:

1. Press the network cable and the crystal head tightly, and re-insert and unplug the wireless network card;

2. Reinstall the wireless card driver.

4. In the software after the wireless network card is inserted and installed, select "Press the access point or wireless router."

button", click "On" on the advanced softap, and follow the prompts on the virtual AP to operate.

1. Make the correct connection according to the manual.

Line: Signal splitter to cat routerwan router lan computer network card.

Note: To use the 568b method to make a cross-twisted pair, not 568a

2. Set the address of the computer network card to be automatically obtained (new router, if it is an old router, the auto-allocation function may be turned off, so it can be set to fixed.)

3. Turn on the computer and type ping in the running to test whether the connection is normal.

Note: The premise is to make sure that the NIC is working properly, and the test method is ping

4. Open IE, enter, the login window appears, the account is admin, the password is empty, and enter the management interface.

5. Choose the correct connection method according to the actual situation, the cell LAN is generally a fixed IP, some may be dynamic IP, if it is ADSL, select PPPoE, fill in the correct relevant information, and it will be done.

Note: Some of them may already be bound to your Mac, so you need to clone them.

6. After saving, you can go to the system status to check whether it can be connected normally.

Plus the model of the route, it will be more detailed.

The local connection IP address of the computer is set to automatically obtained, and after the connection is successful, check the gateway address and enter the routing setting interface through the gateway.

In the WAN settings, just fill in the username and password for surfing the Internet.

Wiring: WAN port of the cat breakout router, LAN port of the computer router.

Connect the network cable to the WAL port of the router,The network cable of your computer is connected to 1234,Just one of those numbers,IP is set to automatically obtain,That's it。

Probably the browser enters the account password prompted, and the admin password is the same.

Then there is a setting, select popp, enter your account password, and save it.

Then you plug four computers into port 1234. The cat can be inserted into the blue mouth.

1.First of all, make sure that your 5 machines have opened the LAN sharing permission, and the general XP system is forbidden to share, and you need to reset it!

2.Connect the router to any computer, go to the router settings management page, select DHCP server settings, then enable the DHCP server, enable the wireless function of the router, and finally save and restart the router.

3.Connect your 4 desktops to the LAN port of the router under 4 excuses, and connect the laptop to the Internet cable with Wi-Fi and WAN.

After setting up, the local office network composed of these five machines has been set up, and each machine can access each other after setting up and sharing.

Open the webpage or enter the password admin and then set up broadband, you should have the account and password, and you can access the Internet after setting.