What is the problem with Haier washing machine E5

There must be a failure e is generally some kind of failure, the meaning of each brand is not the same, it is recommended to find a professional after-sales solution.

E5 is a water level sensor fault.

Here's how to fix it:

1. Use the hot and cold water inlet program, and then answer the hot water for 30 seconds when washing the water inlet, so as to ensure that the water temperature in the bucket of the washing machine does not exceed 50 degrees.

2. It is best not to choose the hot water program, so that only hot water when washing may cause the water temperature in the cylinder to exceed 50 degrees, causing damage to the machine.

E5 means low voltage protection, and the solution: it will automatically resume operation when the grid voltage rises.

When the following numbers appear at the same time, the washing machine failure ** fault cause solution:

E1: Overtime for water inlet or water replenishment, open and close the door cover, check the water inlet valve, etc.

E2: After 6 minutes of drainage, the water level sensor still cannot be reset, open and close the door cover, check the drainage pipe, etc.

E3: The door cover is not closed before dehydration.

The E5 of Haier's old water heater is power-off or overheating, and the thermostat shows that E5 is a temperature sensor fault. If there is no problem with the heating tube and thermostat, replace the overtemperature protector. If the hot water thermostat is broken, it will be heated directly until the over-temperature protector trips, so the thermostat needs to be replaced; The heating pipes are installed in the opposite direction, resulting in excessive water temperature.

The original heating tube needs to be reinstalled and the bent part is kept downward; The safety valve does not have an anti-backflow function, and the over-temperature protector operates due to the dry burning of the inner tank without water, and the safety valve needs to be replaced. Workaround:1.

First, check whether the pulse igniter is normal, whether the gas is sufficient, whether the voltage is abnormal, whether the computer board can work normally, etc. 2.The Haier E5 fault code indicates that the temperature sensor of the water heater is faulty, and a technician should repair or replace it.

The E5 fault code of gas water heater may be a fault of wind pressure, or it may be heat exchange carbon deposition and heating. In case of wind pressure failure, the first thing to check is whether there is strong wind outside. If the wind outside is too strong, the air pressure switch usually won't turn on the water heater.

In this case, you just need to wait until the high winds stop and then return to normal. If the water heater is not maintained or repaired for more than a year, carbon deposits can cause the water heater to not work properly. This is where cleaning comes in.

If neither of these two situations solves the E5 fault code of the gas water heater, then the problem of the air pressure switch of the water heater itself needs to be considered. Check whether the air pressure switch is invalid, check whether the wind pressure detection port is blocked, whether the silicone pipe falls off, or whether the air pressure switch connection line falls off.

The e5 of the washing machine refers to the water inlet that has not reached the washing level within 8 minutes (8 minutes refers to the total water inlet time of each washing stage); This is due to the fact that the water inlet valve is a little blocked, or it may be due to the damage of the solenoid valve, or due to the relatively low water pressure, so the slow water inlet leads to a longer washing time;

You can unscrew the water inlet pipe joint connected to the washing machine, see if the water inlet on the washing machine is blocked by dirt, and clean it to see if this problem is solved; If it still can't be solved, you can only find after-sales maintenance personnel.

Information. Stick.

Library. **。

User. Apply.

Shopping. Posts.

Map. Mini programs.

Note. Procurement.

**。Live broadcast.

**。Hot discussion.

When the Haier washing machine E5 fails, it is generally the cause of the blockage, and the specific problem is that the water inlet does not reach the washing water level within 8 minutes. If there is a problem, you should unscrew the water inlet pipe joint of the Haier washing machine, check whether the water inlet on the Haier washing machine is blocked by dirt, and if so, you need to clean up the dirt;

If there is a fault before the water ingress**, the problem is on the motherboard and the water inlet solenoid valve, first check whether the motherboard is supplying power to the water inlet solenoid valve, no power supply, the motherboard is damaged, there is power supply, water inlet solenoid valve.

When the Haier washing machine has an E5 failure, the filter can be removed from the water inlet of the water inlet pipe, and then the flow-limiting rubber mat can be removed.

It depends on the time period when this failure** appears, such as when the laundry is running, the failure** may be a problem with the motherboard. It may be caused by data loss from the motherboard.

Little Swan Washing Machine Failure**E5: Low voltage protection, automatic resumption of operation after the grid voltage rises.

Common faults and treatment methods of Little Swan washing machine:

Fault 1: Stop the water inlet when the water inlet does not reach the set water level.

Analysis and maintenance: This fault is mainly due to the poor performance of the water pressure switch, so that when the air pressure in the gas collection chamber has not reached the specified pressure, its contact will be converted from the disconnected state to the closed state in advance and stop the water inlet, the specific reasons and treatment methods are:

1) The pre-compression amount of the water level control spring of the water pressure switch becomes smaller, and it can be solved as long as the adjusting screw is screwed to increase the pre-compression of the water level control spring. If the water level control spring becomes less elastic or loses its elasticity, the water level control spring should be replaced.

2) The groove on the cam of the water pressure switch is worn or damaged, and the cam can generally be replaced to solve the problem.

Fault 2: The water inflow must exceed the set water level before the water inlet will be stopped.

Analysis and maintenance: This phenomenon shows that when the actual water level has reached the specified height, the air pressure in the gas collection chamber of the water pressure switch still does not reach the specified value, and the water pressure switch will only operate if the water level continues to rise. The specific reasons and ways to deal with them are:

1) The air conduction nozzle of the water pressure switch gas collection chamber is blocked or leaking. As long as the debris at the air nozzle is removed; Or seal it with 401 glue at the air leakage. If the air hose is aged, kinked, or cracked and leaking, the air hose should be replaced.

2) The pre-compression amount of the water level control spring of the water pressure switch is too large. Just unscrew out some of the adjusting screws to reduce the amount of precompression of the water level control spring.

3) The reversing ejector rod and transmission parts in the hydraulic pressure switch are deformed or damaged. It can be solved by repairing and correcting, and in severe cases, the water pressure switch should be replaced.

Hello netizens, it's a pleasure to accept your questions. Little Swan washing machine E5 troubleshooting method 1, unplug the lower end of the transparent pipe of the water level sensor and blow the air, if you hear the action sound of the sensor, the water pipe is not leaking. 2. Find the sensor and remove it, blow again, if you find that the contact is poor, it is determined that the sensor is faulty and not the problem of the control board.

3. The sensor should be slowly pried open with a thin cone and then removed. 4. Find the contact, if the action is not sensitive when blowing, you can adjust the adjusting screw slightly to make it flexible to open and off. 5. Pay attention to the removal of the contact part, first remove the side shell (the plate is 2 fixed feet, pull off), and then remove the water level control iron pressure plate, spring and pressure cap (one pressure plate and one transmission rod), and then rotate the drive rod core 90 degrees to decompose.

Don't throw away those springs and caps. 6. Restore the machine and test the machine to see if there is still a fault. I hope mine is helpful to you and I wish you a happy life.

E5 means low voltage protection, and the solution: it will automatically resume operation when the grid voltage rises.

Washing machine failure** Failure cause solution.

1. E1 When water inlet or water replenishment is overtimed, the door cover should be opened and closed, and the water inlet valve should be checked.

2. E2 After 6 minutes of drainage, the water level sensor still cannot be reset, open and close the door cover, check the drain pipe, etc.

3. Before e3 dehydration, the door is not closed, and the door cover can be closed.

What type of washing machine, if it is a drum washing machine, E5 should be the reason why the solenoid valve is damaged or the water inlet pipe is blocked or the water pressure is too low. If it's a wave wheel, it's a temperature sensor failure.

Depending on the model of the washing machine, the E5 of the drum washing machine should be due to damage to the solenoid valve or the water inlet pipe is blocked, causing the water to enter too slowly, or the water level sensor is broken, if it is a wave wheel, the temperature sensor is broken.

My Haier XQG60-1000 model has an err5 failure, and it is normal after I press the start pause button again.

The water incomes too slowly, or the water level sensor is bad.

Added: The height of the sewer pipe is 80cm, not low!

Generally, it is the cause of the blockage, and the specific problem is that the water inlet does not reach the washing water level within 8 minutes. If there is a problem, you should unscrew the inlet water pipe joint of the washing machine, check whether the water inlet on the washing machine is blocked by the liquid fiber dirt, and if so, you need to clean the dirt.

This answer applies to most washing machine models such as Haier XQB80-Z1269. Mausoleum imitation.