How to clean the pressure relief valve of Supor electric pressure cooker

The cleaning method of the Supor electric pressure cooker decompression valve is as follows:

1. Lift the pressure limiting valve, clean it with water, and then put the pressure limiting valve body on the pressure limiting valve seat.

Remarks: 1. Cleaning method of electric pressure cooker:

1.Please unplug the power plug before cleaning.

2.Wipe the pot with a rag, and it is forbidden to soak the pot in water for cleaning or spraying with water.

3.Remove the water collection box and wash it, and wipe the upper seat clean with a damp towel.

4.Wash the inside of the lid with water, including: sealing ring, pressure limiting valve, anti-blocking cover, exhaust pipe, float valve, and then wipe clean with a rag.

5.Wash the inner pot with a sponge or non-metallic soft brush, then dry it with a rag.

Second, the cleaning of the sealing ring:

Grasp the support cover tightly and pull the nail upward, clean it, pull the support cover and press down against the support shaft in the middle; After installation, check whether the gap between the sealing ring and the perimeter of the lid is uniform and rotates freely before use; Be careful not to put the top and bottom on the reverse (pull the hand outward).

3. Cleaning of float valve:

Gently move the float valve core up and down by hand, and rinse the food residue of the float valve seal with clean water.

General cleaning. It is best to wash it directly with water.

But the cleaning is done.

Be careful. Rubber rings.

Has it been changed position?

If you won't get it.

It is advisable to find a professional master for this purpose.

Perform cleaning. This valve is for pressure cookers.

It's still a more important component.

It should be adjusted to a suitable level according to the different foods cooked, but I doubt that Supor can do it, my newly bought Supor electric pressure cooker, the first time I use it at night, when the heating is over, just turn to the heat preservation function, the stop valve falls, and it can't achieve the promised pressure holding function at all, let alone pressure regulation.

Cleaning and maintenance:

When using the Supor Computerized Electric Pressure Cooker for the first time, it is advisable to wash the pot with mild detergent and water.

Then wipe dry with a soft cloth. Do not use corrosive detergents or any rough metal scrubbers or rags to avoid scratching the non-stick bottom surface of the pan.

Coatcoat, heat the pan over low heat, and then wipe clean.

It can be activated after wiping.

The anti-blocking cover should be cleaned frequently and kept clean.

1. The pressure limiting valve cannot be disassembled, but it can be pulled out for cleaning. The pressure limiting valve is generally a filling process, the inside is iron, the outside is plastic, it is a whole, so it cannot be dismantled, it must be dismantled, and it can only be destroyed. 2. The pressure limiting valve of the Supor electric pressure cooker can be pulled out directly, but if the pressure relief valve of the pressure cooker does not fall off, it means that the pressure inside is still high.

If you're in a hurry to open the lid, the best way to speed it up is to place a water-soaked towel over the pressure cooker lid.

First, where is the Supor electric pressure cooker check valve located above the sealing cover, that is, the vent of the lid. Li Jian: When the pressure is applied to the pot, do not forcibly open the lid, after the pressure is relieved, the check valve will usually drop automatically, and the lid can only be opened at this time. The main reason for not being able to open the lid is that the check valve is under pressure in the pot and the leakage cannot be lowered, so the lid cannot be opened.

How to deal with the leakage of the Supor electric pressure cooker valveHello dear, 1. Solve the deformation of the inner pot mouth: replace the inner pot 2, the inner pot cover, sealing ring, sealing fixing ring and other parts of the fault solution: repair the inner pot cover, remove the sealing fixing ring hair-stripping or replace the sealing fixing ring.

3. Ball pad rupture or size deviation solution: replace ball pad 4, rice milk or foreign body blockage caused by exhaust Solution: Regularly clean ball pad and steel ball 5, ball gasket sealing ring broken or steel banquet without ball deformation Solution:

Replace the ball gasket sealing ring or steel ball 6, the solenoid valve stem and the sealing ring against the steel ball Solution: Check whether the sealing ring is closely matched with the rod valve or replace the solenoid valve 7, check the crack of the sealing ring of the open rod or the foreign body in the hole Solution: Replace the seal ring of the stop rod or remove the foreign body 8, the hole of the stop rod is crooked or the size is too small (the stop rod can not rise normally) Solution:

Replace the inner pot cover 9, safety valve failure or safety valve seal ring rupture Solution: Replace the safety valve or its sealing ring 10, the pressure is too high due to the loss of control of the control board Solution: Check whether the relay and its related circuit components are damaged, and check whether the thermistor resistance is normal.

It can be washed directly with water, and the one I bought is also Supor's, which is mechanical, and every time I wash it, I wash it directly with water.

Wipe the pan clean with a rag. It is forbidden to soak the pot in water for cleaning or spraying with water. 3.

Remove the water collection box and wash it, and wipe the upper seat clean with a wet wipe. 4.Wash the inside of the electric pressure cooker lid with water, including:

Sealing rings, pressure-limiting air release valves, anti-blocking covers, exhaust pipes, float valves, and then wipe clean with a rag. 5.Wash the inner pot with a sponge or non-metallic soft brush, then dry it with a rag.

6.Wash the pressure-limiting bleed valve seat with a fine brush. 7.

Cleaning of the sealing ring: The sealing ring should be cleaned after one week of normal use. The cleaning method is as follows:

Open the lid of the pot and take out the sealing ring, add 8-12 drops of detergent to two-thirds of the water in a small basin, soak the sealing ring in the basin for two hours (hot water at 60°C), and then rinse three times with clean water. (When you have cooked oily foods such as meat, they should also be washed as described above.) Precautions for electric pressure cooker 1

It is forbidden to use the product in flammable materials and humid environments. 2.The height of the food and water added to the inner pot must be specified in step 2 of the usage method.

3.The sealing ring cannot be damaged, it cannot be replaced by other rubber rings, and the tension ring cannot be used to increase the seal. 4.

Do not forcibly twist the inner steel ring of the lid with your hands or other tools, if the steel ring falls off the lid, please suspend use and replace the lid. 5.The anti-blocking cover should be cleaned frequently and kept clean.

6.When the float valve is not falling, do not force the lid to open. 7.

No heavy objects shall be added to the pressure limiting relief valve or replaced by other objects. 8.The contact surface between the bottom of the inner pot and the heating plate should be kept clean, and the inner pot should not be placed on other heat sources for cooking, and the inner pot should not be replaced by other containers.

9.The inner pot is coated with a non-stick coating, and to prevent scratching the inner wall coating, use a wooden or plastic rice spoon. 10.

Keep warm for a maximum of 24 hours, and should not be used for more than 6 hours, so as not to affect the cooking effect. 11.In the process of heating and cooking, it is found that a large amount of exhaust around the lid of the electric pressure cooker is an abnormal working phenomenon, at this time, the pressure relief safety device is protected, please unplug the power plug immediately, suspend use, and send it to the company's maintenance point for maintenance.

12.When moving the product, please carry the handle and do not lift the handle of the lid. 13.

Users should not disassemble the product by themselves, or replace it with other parts, and the product can only use the company's spare parts. 14.Since the lid of the electric pressure cooker fits with the plastic lid, it is normal for the lid to have bumps and bumps inside.