Water seeps from the bottom of the toilet in the bathroom, and water seeps up from the bathroom floo

If there is water seeping at the bottom of the toilet toilet, check whether it is a leak in the toilet flush, or a leak caused by a blockage under the toilet, or the toilet is permanently loose, or the toilet is not installed properly and there are gaps, or it is caused by uneven floors, etc.

If the edge of the toilet is leaking, then first scrape the glue on the edge, tilt the toilet at a certain angle, see if the rubber ring of the toilet connection test is damaged, replace it if it is damaged, and then let the toilet drain face the lower pipe, and then use new glue to apply the edge of the toilet bowl to the bottom edge.

If the bottom of the toilet is a cement slab, you need to open the cement slab first, then get the cement inside out first, and then re-smear the black cement inside. Then the outermost layer is plastered with white cement.

If the toilet is blocked because there is a foreign object in the toilet, you must disassemble the toilet bowl first and then glue it to fix it. Similarly, due to the long use of time, the leakage caused by the loosening of the toilet bowl also needs to be replaced with spare parts and glue.

The toilet is repaired, do not use it for a short time, and do not flush it. It has been used for a long time and leaks, so you need to replace the toilet sealant.

The toilet leakage caused by cracks at the bottom of the toilet bowl is mainly caused by the poor quality of the toilet, and even the cracks appear when the toilet is fired, and the water leaks out along the cracks when used.

2. The toilet and the ground are generally bonded with glass glue, if the glass glue is too little or the glue is too thin, in the cumulative use, it is easy to appear between the glass glue and the toilet or the ground, in this case, you can see whether there is an obvious gap between the glass glue and the ground, if so, you can shovel the existing glass glue clean, and then buy the relevant glass glue for re-bonding, under normal circumstances, try not to use the toilet in 24-48 hours after smearing.

3. The quality of the water parts in the toilet is not up to par, the toilet parts are aging after being used for a long time, the buoyancy of the float in the toilet tank is not enough, the float is mainly to control the water valve in the water tank, if there is a problem, the water valve can not be automatically closed, and the water will always enter the water, and it is easier to seep out of the base of the toilet when the amount of water is relatively large.

4. It may be that the sealing ring at the bottom of the toilet is not tightly sealed during installation, and the sewage outlet at the bottom of the toilet bowl and the diameter of the toilet are not aligned when the toilet is installed, resulting in the liquid overflowing from the connected place when the toilet is draining or discharging.

Glass glue. Glass glue, a commonly used adhesive in the household, is composed of sodium silicate and acetic acid and organic silicone. Sodium silicate is soluble in water and viscous, and is called water glass in the south and bubble alkali in the north.

The bottom of the toilet in the bathroom is mixed with water, which may be caused by the installation of waterproof measures are not done, you can scrape off the glue, re-do the waterproof and then install it.

It was not installed properly during the installation, and there was a rubber ring at the bottom, which may not be aligned with the eye. You remove it, re-symptomatize it, and it doesn't leak.

Water seepage at the bottom of the toilet in the bathroom may not be installed properly, the underground leather ring can be cut and seen, and then put it on the toilet, and then put the sealant on it, and then use it when the glue is dry, so that it can be.

This indicates that the bottom of the toilet is not tightly sealed with the sewage pipe.

What should I do if the toilet leaks?

Causes of groundwater leakage in the bathroom:

a) The gap between the floor tiles is not sealed. Water from the bathroom seeps through the gaps between the tiles into the cement mortar layer beneath the tiles, and water flows everywhere down the floor. The owner has no basic knowledge of waterproofing, and he can't think that the gaps between the tiles are the next road.

He thinks the bathroom at home is waterproof. In fact, the developer made the caisson waterproof to ensure that the downstairs would not leak. The level of waterproofing of renovation companies varies greatly.

2) The water inlet joint of the toilet squatting toilet is not tightly connected. Because the joints are buried under the tiles, the water seepage is short at the moment of water release. The water in the cement mortar layer should slowly extend to the living room to the wall. If upstairs, it will drip down the stairs.

3) There is a gap between the floor drain and the sewage pipe. Everyone knows that the water on the toilet floor is drained from the floor drain. The problem is that when decorating, due to the various mismatches between the floor drain and the sewage pipe, the connection is often not good.

What materials may be used to remedy it at that time, but after blisters and water flush the floor drain and sewage pipe, there will be spacing and water seepage. (d) There is no space separation between the bathroom shower area and the washing area, and there is no waterproof layer in the floor tile area. At the door of the bathroom, there is no waterproof treatment, separating the dry area from the wet area.

5) Cracked pipes in the wall or leaking tees. It is necessary to test the water pressure. After discovery, the tube can only be changed by opening the abdomen.

OneCauses of leakage in the toilet base

1. The common cause of water leakage is due to:The hemispherical rubber cap that caps the drain is lighter, and the water leaks due to insufficient gravity and not enough when it falls, often need to be repeated again and again to cover the tightness.

2. Leakage at the bottom of the toilet bowl may also beThe connection sealing flange between the toilet outlet and the ground drain is not in place

IISolutions to leaking toilet bases

1. Disassemble the toilet, buy a new flange and install it anew, and fix the toilet with glass glue. The glass glue only plays the role of fixing the toilet bowl on the ground without moving the position, and does not play the role of draining water when the toilet drains. If the main sewer pipe is drained smoothly, the flange will not leak to the outside if it is slightly misaligned.

2. The leakage of the base is easy to turn black with glass glue to make up, and it cannot be used as a leak plugging for a long time. It is suitable for plugging leaks around the foot of the toilet and fixing the toilet.

The primer is not laid, and now the toilet master is only putting sealant on the outer ring, so that it is easy to seep water. It should be to put the toilet down before installation, put a circle of glue on the base, and then hit the outer ring again after installation.

Answer 1: If there is a leak at the edge of the toilet, it is generally at the bottom of it, mainly because the sealing effect has failed, and it is directly related to the fact that the toilet was not installed when it was installed. For example, if the diameter of the ground drain outlet and the toilet pipe is not completely aligned, it will lead to water leakage at the bottom, and there will be a smell at the same time.

2. Another point is that the flange ring is not installed during installation, or the flange ring is not sealed. Long-term use can cause gaps and loosening between the toilet and the floor, which can lead to water leaks at the edges.

3. When encountering this kind of problem, we first need to disassemble the toilet, and then see at the bottom whether the sealing work is not in place, and then clean the bottom of the toilet bowl and reseal it with sealant. Apply a thick layer of glass glue along the edge of the hole in the floor drain, press the toilet tightly according to the drain, and wipe off the spilled glue along the bottom with a rag.

4. It cannot be used within 24 hours after installation, and it can only be used in the later stage until the glass glue is completely solidified and the sealing work is in place.

5. If it is because of the quality of the toilet, some toilets have been used for a long time, the pressure resistance will drop, and there are cracks, in this case, you can only buy and replace the new toilet.

The edge of the toilet base is leaking, don't just stick it with glue, that's a symptom rather than a cure.

When water seeps from the bottom of the toilet, you can use the pull-burst bolt fixing method to solve the problem: place the toilet in the installation position, draw the outline of the toilet base on the ground, and draw the location of the bolt holes in the mounting holes.

Toilet removal begins by unscrewing the connecting tube between the toilet and the wall. Then use a blade to remove the white sealant from the bottom of the toilet that is in contact with the ground, and then remove the toilet.

When installing, first clean the area around the toilet eye, and there should be no sewage. Align the eye of the toilet with the toilet hole on the floor and lay it flat, then lift the toilet left and right, apply a circle of glue to the inside of the toilet, then apply glue to the outside of the toilet and flatten, and use a circle of glue to connect the tube to the wall.

Do not use water after 42 hours of installation. Wait until the glue is dry.

What to do if water seeps at the bottom of the toilet is as follows:

1. If the internal parts of the water tank are aging and cause water seepage at the bottom of the toilet bowl, it is necessary to replace the parts as soon as possible. If there is a problem with the water inlet group and the water outlet group of the toilet, you need to open the water tank and see that the water tank is overflowing, and the water flows out of a water pipe indicates that the water inlet group is broken, and if there is a sound of water inflow, the water outlet group is broken. If the water leaks from the tank, you can take off the drain core and clean up the scale.

After the above problems are removed, if the decoration is not good, it is easy to leak.

2. If it is installed in a specialty store, it is usually padded with a sealing ring inside, and the glass glue around the toilet bowl can be used to prevent water seepage at the bottom of the toilet bowl. Things to prepare: wrench, (if you need to disassemble and install the angle valve, you need to prepare) water adhesive tape, utility knife, glass glue and glass glue gun, toilet special sealing ring (if you need to replace it).

3. If it is a decoration of plumber and electrical tooling, white cement is usually used. Things to prepare: a flathead screwdriver (used to eliminate the original white cement), white cement (when loading from scratch, first mix the water at the bottom of the toilet, then put the toilet seat up and put it steadily, and then use the mixed white cement to seal the toilet footsteps in a circle, and then it can be used when it is dry.)

Be careful not to let the white cement fall into the pipe, otherwise the pipe will be blocked, and the bottom of the flush toilet is also prone to water seepage.

Repair method of leakage at the bottom of the toilet:

1. The toilet is clogged and causes water leakage

The toilet is clogged with foreign objects and cannot be flushed for a long time, resulting in water leakage at the bottom.

Solution: If the toilet plugs the leakage, you can first unclog the toilet to make the toilet unobstructed, and then make glass glue on the edge of the toilet.

2. The toilet is not installed properly, resulting in water leakage

If the toilet is not properly installed, for example, the toilet flange is not aligned with the drain port, then when flushing, water will overflow.

Solution: Reinstall the toilet, replace the toilet flange, and then put a glass glue interface on the edge of the toilet.

3. The glass glue on the edge of the toilet is damaged

The glass glue around the toilet is damaged, which is easy to deteriorate after a long time, resulting in water leakage.

Solution: Re-apply the glass glue, clean the old glass glue on the bottom edge of the toilet with a blade, and then re-apply the glass glue and wait for 24 hours to use.

4. The toilet parts are damaged

The water tank parts of the toilet are damaged, and the water tank of the toilet floats for a long time and cannot be used for aging.

Solution: To replace the damaged parts, you need to know which part of the toilet is damaged, and then replace it.

Dirt cleaning and maintenance method at the bottom of the toilet:

1. Before cleaning the toilet, open the bathroom window for ventilation and take away the miscellaneous objects on the toilet.

2. Pour toilet cleaner around the inner wall of the toilet, cover the toilet lid and soak for a few minutes.

3. Pour disinfectant on the rag and wipe the water tank, flush button, toilet edge, and toilet washer.

4. Use a paper towel to wipe the area where the toilet has been wiped with disinfectant, and use an old toothbrush to clean the sanitary dead corners that are not easy to clean.

5. Open the lid of the toilet, and Qizhen should use the toilet to scrub the inner wall of the toilet, especially the various outlets inside the toilet, and focus on cleaning.

6. Finally, flush the toilet bowl with clean water, borrow the toilet water flow, and flush the toilet brush, so that the toilet bowl is cleaned.

1.Check the water tank and water pipes: First of all, check whether the water tank and water pipes are rotten for water leakage, and if so, they need to be repaired or replaced in time.

2.Check the gasket: Check that the gasket on the bottom of the toilet is aged or broken, and if so, need to replace it with a new one.

3.Check the screws: Check whether the screws at the bottom of the toilet are loose or missing, and if so, need to tighten or replace the screws.

4.Check the drains: If none of the above solves the problem, you need to check whether the drains are blocked or damaged, and if so, you need to clean or repair the drains.

5.Please ask the professional personnel to repair: if the above methods cannot solve the problem, it is recommended to ask a professional to repair.

Water seeps from the bottom of the toilet, dismantle the toilet first, and then reinstall the toilet.

The first step is to dismantle the toilet

Remove all the glass glue from the junction between the bottom of the toilet bowl and the floor, and use a wallpaper knife to cut it. Then you can pull the glass glue off with your hands, so that you can remove the toilet from the ground; Then we can check the installation of the seal.

The second step is to reinstall the toilet

Check the sealing ring at the bottom of the toilet and install it in place, or replace it with a new good sealing ring, and then install the toilet on the ground drain pipe, and finally put glass glue on the part where the bottom of the toilet bowl and the floor tile meets, so as to complete the repair of the leakage at the bottom of the floor toilet.

What is the substructure of the toilet?

The first part is the outlet pipe at the bottom of the toilet. The lower outlet pipe of the toilet bowl is a water outlet made of ceramic. When we turn the toilet over and look at the bottom of the toilet, we will find that the bottom of the toilet has an almost S-shaped elbow, and then there is a ceramic pipe that comes out of the bottom of the toilet, which is the outlet pipe of the toilet.

The second part is the connection on the toilet outlet. Generally speaking, the toilet outlet pipe is covered with a rubber sealing ring, the role of the rubber sealing ring is very large, it is a key component to realize the connection between the porcelain outlet pipe and the PVC pipe at the bottom of the toilet. So the rubber ring must be installed correctly and in place.