How to fix a leaky toilet, how to fix a leaky toilet

1. The process of checking and repairing the leakage of the toilet is: look-listen-find-repair.

2. Look, that is, check whether there is water overflow on the outside of the water tank and on the ground near the toilet; Listen, that is, when there is a filling time in the water tank, if the usual filling time is exceeded, you can hear the sound of water entering the water inlet of the toilet; Find, that is, open the toilet tank lid first to see if the irrigation height has exceeded the horizontal line marked by the toilet tank buoy; After finding the factor, repair it; Repair: After finding the water leakage factor of the toilet, replace the corresponding accessories and pipe fittings after finding the things.

3. Open the water tank and see that the water tank is full and the water flows out of an overflow pipe, which means that the water inlet group is broken. This necessitates the repair or replacement of the inlet or outlet group.

4. If it leaks from the bottom of the toilet after flushing the toilet, and it is accompanied by a smell, then it can be judged that the seal between the drainage pipe at the bottom of the toilet and the toilet is not good enough, which requires re-sealing.

3. In the case of unobstructed drainage, the dirt flows backwards, and the treatment of this situation is to determine whether the drain pipe is not unobstructed, if it is caused by unobstructed drainage, it is necessary to let the product seller reproduce the installation of the toilet, which is generally when the toilet is installed soon.

5. If there is water seepage on the surface of the toilet, it may be that there is a crack in the toilet itself. The detection method is very simple: first turn off the water inlet valve, then drain the water in the toilet tank, and then add red ink or ink to the residual water tank, wait for 30 minutes, and observe where the water seeps.

In this case, it is not advisable to repair the toilet, and replacing the toilet is the only way.

1.First, use a knife to cut the glass glue at the junction between the toilet bowl and the floor tiles, and then unscrew the bolts that hold the toilet open.

2.Raise the toilet a little higher. Never pull or push the toilet bowl into place. It is more troublesome to break the sewer pipe.

3.Then check the sewer pipe for cracks, and then connect a PVC pipe of the same thickness, stick it with PVC, put the toilet on the top and try it, maybe the length is not suitable, and then use a saw blade to see until the toilet can stabilize and stick to the floor tiles.

4.Test the water and it won't leak. Glue the base to the floor tiles with glass glue and tighten the screws to secure the toilet. Don't shake the toilet back and forth for three days. Just wait for the glass glue to dry.

There are several ways to repair a leaky toilet:

1. If the bottom edge of the toilet is leaking, if it is accompanied by a smell, then it can be judged that the seal between the drainage pipe at the bottom of the toilet and the toilet is not good enough, which requires re-sealing. In this regard, it is necessary to remove the toilet first and then reinstall it, and pay attention to the sealing must be in place during the period.

2. If there is a leakage in the toilet tank, the reason is usually the aging or damage of the water parts. As a result, the water level reaches the set height, but the water parts in the water tank cannot close the water inlet in time, resulting in water leakage.

3. Other situations are mainly divided into rubber ball valves that are broken, not tightly sealed, and leakage; and the rubber gasket of the drain under the ball valve is aging and the sealing is not tight, and only the parts need to be replaced in these two cases.

Precautions for choosing a toilet:

Generally speaking, if the quality of the toilet is good, then its surface must be smooth, rich and clean, this kind of toilet can last longer, and the probability of problems is relatively small.

Secondly, it depends on the caliber of the toilet, you can compare it with your fist, if the caliber is just about the same size as your fist, and the surface of the toilet is glazed, it means that it will be more convenient to use in the future, not only has a faster sewage speed, but also is not easy to hang dirty.

1. Look: First of all, open the toilet tank, let's see what level the water scoop inside the water tank is at when it is full of water. If the water inside is full and the tank is still flooding, then there must be a leak coming out. This is easier to handle.

2. We use water to pull the card position of the water scoop up and down, and the sensitivity of the water scoop is sold, if it is not smooth, or it is difficult to move, then the water scoop is faulty.

3. If the water scoop is faulty, you can remove the equipment of the water scoop and clean it, if you don't know how to disassemble it, just put dry water directly in the water tank and clean it with dish soap or laundry detergent.

4. Check the interface of the stainless steel hose outside the water tank and the position of the water tank to see if there is any water leakage. Sidelink teasing.

5. If there is no problem inside, then the only thing that may cause a problem is that the surface of the toilet is cracked.

Find out the real cause of the leak at the bottom of the toilet bowl and see if it is a leak at the bottom of the toilet bowl or the toilet flush, or if there is a blockage under the toilet. If the rim of the toilet is leaking, just scrape the glue off the rim. If a hard object clogs the toilet, you need to disassemble the toilet bowl and then glue it to fix it.

Extended information] 1. Toilet is a sanitary appliance in the field of building water supply and drainage materials. The main technical characteristics of this utility model toilet are that: in the upper part opening of the existing toilet S-type water trap, install a cleaning bolt, similar to the drainage pipeline to install the inspection port or the cleaning mouth to clean up the silt, after the toilet is blocked, the user can use this cleaning bolt to remove the blockage conveniently, quickly, hygienically, economical and practical.

Second, the toilet is technically characterized in that a cleaning bolt is installed in the upper part opening of the existing toilet S-type water trap, and its cleaning bolt is mainly made up of an inspection port and a cleaning bolt gun, and the inspection port is embedded on the reserved mouth of the upper part of the S type trap, and the cleaning bolt gun is a tool used for removing silt.

3. The toilet can be divided into two types: split toilet and connected toilet, generally, the space occupied by the split toilet is larger, and the space occupied by the connected toilet is smaller. In addition, the shape of the split toilet should be more traditional, ** and relatively cheap, and the one-piece toilet should be novel and high-end, ** relatively high.

Fourth, the outlet has lower drainage, (also called the bottom row) and horizontal drainage (also called the back row). The horizontal drain is on the ground, and a hose should be used to connect it to the back outlet of the toilet. The drain at the bottom row, commonly known as the floor drain, only needs to align the drain of the toilet with it when using.

Fifth, the split toilet has a high water level, sufficient punch, many styles, and is the most popular. The split is generally a flush type launch, and the flushing noise is large. Because the water tank and the main body are fired separately, the yield is high.

The selectivity of the split is limited by the pit spacing, if it is much smaller than the pit spacing, it is generally considered to build a wall behind the toilet to solve the problem. The water level of the split is high, the flushing power is strong, and of course the noise is also loud. The split style is not as good as the one-piece one.

Sixth, the shape of the conjoined toilet is more modern, the lower level of the split water tank, the water used is slightly more, and the lower grade is generally higher. The conjoined body is generally a siphon type drainage, and the flushing is silent, because its water tank is fired together with the main body, which is easy to burn out, so the yield is low. Due to the low water level of the conjoin, the pit spacing of the conjoined is generally short, in order to increase the flushing force.

The conjoined body is not limited by the pit distance, as long as it is smaller than the pit distance of the house.

The leakage of the toilet is caused by the lack of installation and gaps.

Solution: 1. Scrape off the glass sealant on the contact between the base of the toilet bowl and the ground.

2. Copy the toilet bowl to a certain angle and check whether the sealing ring on the sewage outlet of the toilet bowl is damaged and the sealing is not tight.

3. The new toilet discharge pollution sealing trap is used in the toilet drain outlet.

4. Re-apply glass glue to the part where the toilet is in contact with the ground.

Precautions: 1. Regularly clean the pipe of the toilet or punch the filter with water, and use a nylon brush with a long handle to clean it with soapy water when cleaning, at least once a week.

2. Be cautious when using, avoid sewage sediment blocking the return port, and try not to pour cement, lime, paint and other substances into the toilet bowl every day, so as to prevent the sediment from precipitating and agglomerating in the toilet bowl and clogging after a long time.

3. Prevent feces from blocking the air return hole, it is best not to throw paper pads and other things that are easy to clog in the toilet, if it is blocked, it should be sucked out immediately with a leather suction device, and the return air hole of the flush toilet should be checked daily to ensure that it will not be blocked.

4. Make sure that the air return hole is normal, if you find something blocked, check whether it can operate normally, and it is best to clean it up immediately if it is blocked.

5. There are a lot of bacteria in the toilet seat, so we should also pay special attention to the need to clean the toilet in time after use, in addition, the toilet is also easy to stick to feces and urine stains and other dirt, and if there is still residue after flushing, it is necessary to use the toilet brush to clean it in time, otherwise it will be easy to appear macula after a long time, resulting in the breeding of mold and bacteria.

If the rubber ball valve is damaged, the seal is not tight, and there is a water leak, it needs to be replaced immediately.

Check if the flush switch is reset. The plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored. Generally, the switch can be reset by repeating it several times.

Check whether the rubber gasket of the drain port under the ball valve is aged, the seal is not tight, and the problem needs to be replaced, check whether the connection between the spherical float of the water tank and the water inlet switch is loose, whether the float is in place and whether the switch is not closed, so that the water inlet does not stop, and the water flows out from the upright drain pipe after the water is full, as long as the connection between the float and the water valve switch is tightened.

Precautions for the use of toilets.

It should be noted that when the toilet is rinsed and cleaned with warm water, the water temperature should be controlled at 1 -45, and superheated water should not be poured into the toilet to avoid the occurrence of the toilet**.

Users need to pay attention not to throw newsprint, diapers and other easily clogged items into the toilet for flushing, easy to block, if there is a blockage, it should be discharged immediately with a skin suction device.

In order to prevent damage and water leakage, do not hit the ceramic so as not to hit the cover plate and seat with excessive force, and do not clean it with steel brushes and strong organic solvents to avoid damaging the glaze of the product and corroding the pipe.

The above content refers to Encyclopedia - Toilet.

People's Daily Online-Reduce health hazards in the bathroom It is important to flush the toilet properly.

The leaking toilet may be caused by the material of the water tank, and the toilet tank is leaking and needs to be replaced.

The material of the water tank is not good or the internal parts of the water tank are old, which will lead to the leakage of the toilet wheel slag water tank, and the toilet produced by inferior materials is usually not good or bad on the outside, but the small parts inside may be damaged due to infrequent use, of course, there are also some cases because the toilet tank has been used for a long time, which makes it aging and deteriorates, resulting in problems with the quality of the toilet tank, which causes water leakage.

Solution: Layan quietly disassembles the toilet tank and checks them one by one to see if the parts in the toilet tank are in good condition. If there are parts that are broken, they can be repaired, and it is best to replace them if they cannot be repaired, if they are too inferior in the case of more damage, it is recommended to replace the entire water tank, so as not to bring more serious consequences.

Other reasons

Leakage of toilet tank caused by drain valve failure, the drain valve of the toilet is mainly responsible for the water of the toilet tank, generally speaking, many situations may be a problem with the toilet drain valve, there may be cracks and deformations in the installation hole, or a series of reasons caused by carelessness in installation. Solution: Since the drain valve needs to be tested with many professional tools, it is recommended to have a professional repair it.

The leakage of the toilet tank caused by the failure of the sewer pipe, the leakage of the toilet tank may also be due to the problem of the sewer pipe, the sewer pipe is connected to the toilet tank and a pipe that transports water, and the possibility of leakage of the toilet tank is also very large. Maintenance method: Carefully check the interface between the toilet bowl and the sewer pipe, whether it is loose, or whether the pipe is broken, if it is, you need to replace the pipe again, if it is just not connected, you can use some iron wire or fixing material to fix it.

The method of repairing a leak toilet is as follows:

1. If the edge of the toilet is leaking, first remove the surrounding rubber stains, replace the damaged chain rubber ring, install the toilet, and reapply the sealant.

2. If there is a leak at the bottom of the toilet, it may be that the sewage outlet is not aligned, and it is recommended to re-open the toilet to be re-opened, aligned with the sewage outlet, and sealed well.

3. If the toilet tank is leaking, the water tank should be disassembled, the water parts should be fastened, and sealed with glass glue, if the water tank is broken, it needs to be replaced.

How to choose a toilet

1. Weight. The heavier the toilet, the better, the weight of an ordinary toilet is about 50 catties, and a good toilet is about 100 catties. The density of the toilet bowl with large weight is high, and the quality is relatively passable.

2. a water outlet.

The drain hole at the bottom of the toilet is good one, and the more drain holes there are, the more it affects the punch. The water outlet of the bathroom is divided into lower drainage and horizontal drainage, and the interval between the drain ** and the wall behind the water tank should be measured, and the same type of toilet should be bought to sit at the opposite distance, otherwise the toilet can not be installed.

3. Glaze. Pay attention to the glaze of the toilet, the glaze of the toilet bowl should be smooth and smooth without blistering, and the brilliance should be saturated. After overhauling the glazed surface of the outer surface, you should also touch the drain of the toilet, if it is clumsy, it will easily cause hanging in the future.

4. Caliber. Large-diameter sewage pipes and glazed inner surfaces are not easy to hang dirty, and the sewage is rapid and powerful, effectively preventing blockage. Test method, put the whole hand into the toilet mouth, generally can have a palm capacity is better.

5. a water tank. Flush toilet storage tank leakage in addition to the significant dripping sound can be determined, generally not easy to find, simple inspection method is in the toilet tank dripping oak quietly into the blue ink of the beam, stir well to see if there is blue water flowing out of the toilet outlet, if there is a leak in the toilet.