The toilet has some shaking, how can you hold it in place?

The toilet has been used for a long time, and the bottom is added to the water to soak and can be loosened. What should I do if the toilet is loose? What should I do with the bottom of the toilet? Let's take a look.

What should I do if the toilet is loose?

1. Change the seal.

2. The base is loose in an open place, such as a small section of wire, until you don't shake it, and finally play with glass glue.

Water. 3, go to the toilet, wipe the toilet and the floor, the amount is good, the toilet is in the middle, use a pencil line, then take the toilet, pencil line, on the glass glue, toilet seat, wipe the circle with hand glue water, there is no water on the day, do not sit in the toilet until the glue is dry.

What should I do if the bottom leaks?

Leaking toilet base. This is precisely what many friends think is a problem with the quality of the toilet, in fact, there is a drainage phenomenon, that is, there is a problem with the connection of the toilet base during installation.

If there is a leakage, first of all, we must determine the cause of the leakage, if it is a toilet quality problem, such as a crack in the wall, then you need to replace the toilet. Similarly, if it is sealed between the toilet and the sewage between the toilet, it needs to be treated.

Method. <>

1.Scrape the toilet base and the grounding contact part.

3. Adopt a new toilet sewage sealing ring and sit in the toilet row;

4.Align the sewage with the sealed seals, down the toilet, and put the toilet.

5.Apply glass glue to the toilet part with the floor.

Precautions: If the original toilet is installed, there is a fixed expansion bolt at the fixing hole of the base.

And the nuts must be tightened.

Then follow the second step above, then before the fourth step, and then before the fourth. The screw holes swell in the original floor. The waterproof coating is fully filled, then the 4th, 5th, and then screwed back the nut.

The reason for the bottom of the toilet.

1. The toilet is not installed when it is installed, resulting in the diameter of the ground sewage port and toilet sewage. There will be yellow water.

Water and smell. 2. The installation is not professional, there is no flange dish (the flange has a good fixation and prevents spillage).

3. Long-term use is suitable for toilet and grinding loose.

4.The problem with the bathroom bracket itself, there are cracks in the ceramic.

5. The internal parts of the water tank are aging.

6.There is a problem with the water supply group or outlet group.

7. Pumping toilet tank leaking.

Buy a hot melt glue gun and fix it with hot melt adhesive, which can stick to most materials and is very easy to use.

I have too much say in this, the two toilets at home are easy to shake before, you must choose a good special glass glue, such as the toilet base if the water leaks, you must not stick the glass glue there, you must choose a dry place, which can increase the adhesion between the toilet and the ground.

I think you can fix it at the bottom of the toilet bowl with glass glue and put a circle of glass glue to make it waterproof and not let the toilet continue to shake.

Just apply a layer of glue to the ground to stick to it, so that it will not melt, and it will not cost anything, it is simple and fast.

The toilet began to shake, and it was found that the underneath was no longer in touch with the ground. How to fix?

How to fix the toilet: 1. Take out the glass glue. 2. Under the premise that the toilet does not leak, use glass glue to fix the connection between the toilet bowl and the ground.

3. If the version has been glued to glass before, take out a utility knife. 4. Use a utility knife to cut the previous glass glue into Heng Lao. 5. Continue to fix the glass glue orange on the non-fitting place.

The way to deal with the problem of the floor and the bottom of the toilet does not fit the round eggplant: 1. Use glass glue to glue the part where the bottom of the toilet meets the ground. 2. Glass glue has strong adhesion, and glass glue can be used.

Yes, if you want to fix the toilet, you need to use special glass glue. If the quality of the glass glue purchased is not too hard, and the bottom of it leaks in the later stage, it is easy to make the glass glue fail, and the adhesion between the toilet and the ground will not achieve the effect, so there will be shaking. It is necessary to remove the original glass glue and purchase a new glass glue with excellent quality.

It is also necessary to pay attention to the application of glass glue, which cannot be used directly after fixation, and can only be used after it is completely solidified, which generally needs to reach one day and one night.

It should be possible, the bottom of the toilet in many bathrooms was originally fixed with glass glue, and the toilet in this bathroom is shaking, so it can naturally be re-fixed with glass glue.

OK. However, it is best to clean up the original glue of the toilet, keep the ground dry, make a circle of the glue according to the size of the toilet, sit the toilet on the glue, and smooth and seal the gap between the toilet and the ground with the extruded glue by hand.

The toilet has some shaking, how can you hold it in place?

Hello dear, I am happy to answer for you: if you want to fix the toilet, you need to use a special glass glue. If the quality of the glass glue purchased is not too hard, and the bottom of it leaks in the later stage, it is easy to make the glass glue fail, and the adhesion between the toilet and the ground will not achieve the effect, so there will be a shaking situation.

In addition to fixing it with glass glue, we can also fix the position of the toilet seat, bolt it and install it, and then remove all the nuts, and then adjust the position according to your sitting posture to adjust its flatness.

The frequency of use of toilets is very high, so in addition to buying high-quality toilet products, later construction is also very critical, otherwise it is easy to have problems after using it for a period of time. If the toilet bowl is loose, it needs to be repaired as soon as possible, otherwise it may lead to more serious problems.

Repair methods for loose toilets and floors:

1. There is no water leakage. If the toilet is loose but there is no water leakage, it is recommended to remove the original glass glue at the bottom of the toilet with a utility knife, and apply the glass glue evenly at the junction between the bottom of the toilet bowl and the ground, and wait for 24 hours to make sure that the glass glue is completely solidified before it can be used normally.

2. If the toilet is loose and seeping. It is recommended to first separate the toilet from the ground, then wipe the bottom of the toilet and the floor with a dry towel, replace the seal, and finally fix the toilet with glass glue or cement. Note that this situation needs to wait for 7 days before it can be used normally, which is relatively long.

3. The ground is uneven. If the bottom of the toilet is loose due to the unevenness of the ground base, the oak fan should unload the toilet bowl and re-level the ground base. Reinstall the toilet after leveling is complete.

Toilet installation precautions:

1. After the toilet is installed, it cannot be used immediately, and the glass glue must be completely solidified before it can be used with water, and the curing time is 24 hours. Be careful not to use cement directly as an adhesive, because cement itself has swelling properties, and over time, it will lead to cracking and displacement of the base of the toilet.

2. After installing the water tank accessories, check whether the water tank is normal and free of leakage. Check whether the water inlet and seal of the inlet valve are normal, whether the valve installation is flexible, etc.

3. The sewage effect of the toilet is very critical, install the accessories in the water tank, fill it with water, try to drain the flush, if the water vortex is rapid and fast, it proves that the water is more smooth, otherwise, check again to see if there is a blockage.

The first observation is that it is loose, and then it is repaired, repaired by yourself or by finding a maintenance master.

1. Change the sealing ring.

2. If the base is loose, pad things in an empty place, such as a small section of wire, so that it does not shake, and finally play a circle of glass glue.

3. Get the toilet up, dry the toilet bowl and the floor, measure the distance between the front and back, put the toilet in the middle, draw the line with a pencil, and then take the toilet away, on the pencil line, on the glass glue, on the toilet seat, wipe the outside glue with your hands, do not flush for a day, do not sit on the toilet until the glue dries.

4. If the bottom of the toilet is leaking, it may be that the connecting sealing flange between the toilet outlet and the ground drain cannot be installed to judge the roll. At this point, you need to disassemble the toilet, buy a new flange and install it from scratch, and then fix the toilet with glass glue. The glass glue only plays the role of fixing the toilet bowl in the ground without moving the position, and does not play the role of draining water when the toilet is drained.

If the main sewer pipe is drained smoothly, the flange will not leak to the outside if it is slightly misaligned.

If the toilet starts to loosen, the following inspections and treatments are required:

1.Check that the support washer is trapped in rock and not damaged. There is a rubber isolation layer and a metal clamping layer in the washer, and if the isolation layer is damaged, the gasket needs to be replaced.

2.Check that the ring is normal. The ring normally appears on top of the support washer and holds the toilet seat. If the ring is missing or damaged, it needs to be replaced.

3.Tighten the fixing bolts. Adjust and gently screw the fixing bolts to secure the toilet to the floor. Bolts that are too tight may cause damage to the washer, and need to be properly carried.

4.Check that the ground is level. If the floor is uneven, you can stabilize the toilet position by using gaskets or increasing the number of gaskets. Hidden Bridge.

5.Tighten the floor drain pipe. Check whether the floor drain pipe is loose, and if it is loose, you need to tighten the water outlet and connector at the connection.

6.Check the water outlet. The water outlet may be clogged with garbage, causing the water pressure to increase and need to be cleaned.

7.Use a restorative. It is necessary to select the corresponding ultrasonic repair agent according to the gasket material to bond the gasket to the ground.

In general, when the toilet starts to loosen, you need to initially check the support system for problems, then replace the damaged parts or use a repair agent as appropriate, and finally adjust and tighten the set bolts to secure the toilet. If the problem is severe, it is best to replace the toilet directly.

Hopefully, the information provided will help you with this. If you have any questions, please feel free to ask.

If the toilet bowl is loose, you can put glass glue around the toilet bowl to fix it.

After drying the gap below without water, find a few pieces of plastic to be flattened so as not to shake, buy a bucket of transparent glass glue, make a circle in the gap between the toilet and the ground, and use it normally after the glue dries the next day.

When the toilet is loose, first observe that it is loose to find the cause, and then carry out the corresponding repairs. If you sit loosely, you can order something in an empty place, such as a small section of wire as long as it does not shake, and finally put a circle of glass glue on it. If you don't know how to repair it, you can find a professional master to repair it.

Putting a layer of glass glue around the toilet bowl in contact with the floor can not only play a fixed role, but also prevent water leakage. If you are still afraid of loosening, there are two small holes in the bottom of the toilet, which can be fixed to the ground with two expansion screws.

Clean the loose surface and let it dry. Then use plastic electrical tape to glue both sides of the part to be bonded. Wipe the glass glue nozzle with a knife and cut it diagonally; Glue the parts to be glued; Flatten with your fingers; Finally, remove the electrical tape. After pressing, use after 24 hours.

1. Change the sealing ring.

2. If the base is loose, pad things in an empty place, such as a small section of wire, so that it does not shake, and finally play a circle of glass glue.

3. Get the toilet up, dry the toilet bowl and the floor, measure the distance between the front and back, put the toilet in the middle, draw the line with a pencil, and then take the toilet away, on the pencil line, on the glass glue, on the toilet seat, wipe the outside glue with your hands, do not flush for a day, do not sit on the toilet until the glue dries.

The easiest way to do this is to clean and dry the toilet base all around, then glue the glass around it and use the toilet again after 24 hours!

It can also be fixed with expansion bolts, but be sure enough that the water pipes and waterproofing will not be drilled into the ground or wall when drilling!

Use cement grout, if it is convenient, you can also use glass glue.

The toilet seat cushion will fall off by itself, and I don't know what the problem is, and it won't be used slowly or by hand like the original.