-
Anonymous users2024-02-121. On-site inspection.
Sports wood floor maintenance staff, or stadium staff, when they find that the sports wood floor is soaked in water after work, don't panic first, be calm. Inspect the soaking site at the first time to eliminate potential safety hazards, such as whether there are wires, electrical appliances, flammable and explosive materials on the soaking floor, etc.
Then according to the degree of water immersion of the sports wood floor, a solution is formulated.
2. Soak in water lightly.
If the sports wood floor is lightly soaked, the lightly soaked and damp floor can be wiped dry and ventilated. If necessary, disassemble the sports wood floor to observe whether there is water on the ground and observe whether the floor is obviously deformed. If so, it needs to be removed and dried, and reinstalled.
3. Heavy soaking.
Sports wood flooring that is seriously damp or soaked in water for 30 minutes will be deformed, expanded, and lost its luster. Such sports wood flooring is basically scrapped and should be replaced, and attention should be paid to removing the moisture under the floor and drying it.
4. Precautions.
After the sports wood floor is soaked in water, it is important to pay attention to the fact that it cannot be blown by hair dryer, exposed to sunlight, or dried, which will accelerate the serious deformation and damage to the surface of the sports wood floor of the basketball hall.
-
Anonymous users2024-02-11Remove the floor and do a moisture-proof treatment (e.g., a layer of plastic film), and then lay the floor, and be sure to stick tape between the mats.
-
Anonymous users2024-02-10Drum repair of composite flooring: disassemble the ventilation and dryness, remove the expansion joint debris, polish and repair, and replace the wooden floor.
Method 1: Disassemble and ventilate boring.
Removing the arching wood block and the surrounding floor to ventilate it can alleviate the arching problem; Pry up the floor of the arch in a large area, wait for the air and the dragon master to dry, and then lay the floor back; Pay attention to the normal contact between the floor and the outside world to make it balanced with the atmospheric humidity; If the arch is severe, you can think about changing it. In order to avoid arching of the floor, experienced laying masters will leave a certain small gap in advance when paving the floor, leaving room for "thermal expansion and cold contraction" for the floor.
Method 2: Clear the expansion joint debris.
If the expansion joint is blocked, the contents of the expansion joint will be removed.
Method 3: Grinding and repairing.
If the diameter of the bulge is less than or equal to 2 cm, if it is laminate flooring, it should be replaced; If it is a parquet floor, it can be tied up on the original board to stop grinding and repairing, and the color of the original floor is as similar to the difference as possible.
Method 4: Change the wooden floor.
Replace the new Yinxin flooring, when repairing, remove the deformed floor plate, pave the air with cement, and replace it with a new floor, so that the floor will be as smooth as ever (during the warranty period, the consumer can contact the supplier directly to stop the change).
-
Anonymous users2024-02-09Method 1: Disassemble and ventilate and dry.
Removing the arching wood block and the surrounding floor to ventilate it can alleviate the arching problem; Pry up the floor at the arch in a large area, wait for the ground and keel to dry, and then lay the floor back; Pay attention to maintaining the normal contact between the floor and the outside world to balance it with the atmospheric humidity; If the arch is severe, it can be replaced. In order to prevent the floor from arching, experienced laying masters will leave a certain small gap in advance when paving the floor, leaving room for "thermal expansion and cold contraction" for the floor.
Method 2: Remove the debris of the expansion joint.
If the expansion joint is blocked, get the contents of the expansion joint out.
Method 3: Grinding and repairing.
If the diameter of the bulge is less than or equal to 2 cm, if it is laminate flooring, it should be replaced; If it is a parquet floor, it can be repaired by sanding and repairing the original board, which is as close as possible to the color of the original floor.
Method 4: Replace the wooden floor.
Replace the new floor, when repairing, remove the deformed floor plate, pave the floor with cement, and replace it with a new floor, so that the floor will be as smooth as ever During the warranty period, consumers can directly contact the supplier for replacement.
1. Keep the floor dry and clean, and do not mop the floor with a dripping mop, or wipe the floor with alkaline water or soapy water, so as not to damage the gloss of the paint surface; If the air in your home is dry, make the mop wetter or put a basin of water on the heater or humidify it with a humidifier. Urban Hunter. >>>More
Laminate flooring and solid wood flooring have many differences, such as material, **, maintenance, environmental protection and other aspects have a lot of differences. Hardwood parquet has the advantages of beautiful and natural solid wood flooring, comfortable foot feeling and good thermal insulation performance; It also overcomes the shortcomings of solid wood flooring due to the shrinkage of a single body and easy to warp cracks. In addition, parquet is easy to install, and there is generally no need to tie the keel. >>>More
The ** of solid wood flooring must be much higher than the other two, but it also depends on the tree species, the cheapest solid wood floor is more than 200 yuan per square meter, and ** has a relationship with the specifications. Parquet only has the surface layer of the solid wood floor, and the base material is fast wood, so it is lower, the general** is about 170 200, of course, there are also expensive ones. There is a big difference between the solid wood floor of the same tree species and the solid wood composite, for example, take teak as an example, the solid wood teak floor is generally more than 800 yuan, and the solid wood composite is generally around 300 yuan. >>>More
First, the reason for the hollowing of the wooden floor.
1. The original ground is not cleaned, the paving mortar has too much moisture, and the workers are not skilled enough. >>>More
Here's how to deal with it:1. If the soaking of the composite floor is not very serious, then you can use absorbent tools to absorb the moisture on the surface of the composite floor, such as dry rags, sponges, vacuum cleaners, hair dryers, etc. If you use a hair dryer, use cold air to prevent the floor from deforming. >>>More