It didn t take long for the floor to be installed, what was the reason?

Updated on healthy 2024-07-06
11 answers
  1. Anonymous users2024-02-12

    It may be because your wood is not of good quality, there are a lot of bacteria, and there is a lot of glucose in it that makes up the mold, so it will become moldy.

  2. Anonymous users2024-02-11

    It is because there is a high probability that some water will appear below in the process of use, and there is no way to treat it in time, so it is easy to get moldy, and this is also because of long-term habitation.

  3. Anonymous users2024-02-10

    That's because when the house was renovated, the cement under the floor had not yet completely dried, and it had been fully renovated, which led to mold in the later stage.

  4. Anonymous users2024-02-09

    Introduction: If you find that the floor has mold not long after installation, be sure to find the cause.

    If you find that the floor is moldy not long after installation, many people will think that this is the problem, at this time you should see if you have infiltrated a lot of water when mopping the floor, if a lot of water has penetrated in, you should wipe it in time, and do not let the water seep into the bottom. Some people do laundry at home, and if you find water on the floor while washing your clothes, you should wipe it down in time to prevent it from seeping underneath. When choosing a floor, you must choose a good floor, don't think about being cheap, some people must consider whether the wooden floor is used when choosing a wooden floor, if the wooden floor is not practical, you should also choose tiles, which are relatively good and easy to take care of.

    If there are children in the house, you should change your choice appropriately, so that it will be more convenient for you to use, and you must replace it in time if there is mold.

    If you find that there is mold on your wooden floor, you should see if there is water seepage, if there is water seepage, then you should replace these bad wooden floors in time, and replace them with new wooden floors, so that there will be no bad phenomena. Usually, if the ground is mopped, it is necessary to wipe the water clean in time to avoid bad situations. Some people always don't know how to wipe the wooden floor, so at this time we must do a good job in the maintenance of the floor, if the floor is always moldy, there will be a certain situation, usually we must adjust it, if the floor is moldy, then we must comprehensively change, and then install some good floors, so that the phenomenon of mold can also be avoided.

    If you find that the floor has mold not long after it has been installed, you must find the reason, take a look at the problem, and you can also find a professional to analyze it.

  5. Anonymous users2024-02-08

    There are many people who are excited to install the floor and move in immediately, but when they close the house, they find that the floor is moldy not long after it is installed. This incident must have made everyone feel very angry, and they were also confused, and they didn't know what caused it. Today, I'm going to tell you about the moldy floor that hasn't been used for a long time, what's going on?

    Like many southern regions, because the weather is very humid in all seasons, most of them will not install wooden flooring, otherwise the floor may not last for a month and start to mold. There are also some netizens who don't know how to clean up after installing the wooden floor, if everyone takes a wet mop to mop the floor, and does not open the window for ventilation, the wood will absorb moisture. Over time, the wood will rot, so you should choose to use a dry mop when cleaning up.

    When moisture enters the floor, bacteria will grow on the floor, and then it will start to mold from the inside out, in which case all the flooring can only be removed and rebuilt.

    As I said earlier, there are many southern areas where there is often rainy weather, so they don't dare to install wooden boards, otherwise there will be mold, so you can't prevent weather problems. Like many areas in Jiangsu, Zhejiang and Shanghai, as soon as the rainy weather arrives, the wooden floor begins to become damp, and over time it begins to become moldy. Therefore, when decorating, you should also choose the floor according to the actual situation, and what is even more exaggerated is that some netizens even have mushrooms growing in their homes.

    There are some floors with hidden water pipes, if you find that the floor is moldy after renovation, you can ask the designer to pry open a piece of the floor to see if it is a leaking water pipe. Generally, the wires and water pipes in the home are installed under the floor, if the water pipe is leaking, it is very dangerous, which may lead to underground short circuit and leakage. When you find that some floors are starting to get wet, you should pay attention to these situations.

  6. Anonymous users2024-02-07

    The wooden board is more afraid of moisture, it may be that it is usually cleaned with a wet mop, or the water is sprinkled on the wooden floor, the water does not evaporate in time, the wooden board absorbs the water, the water pipe is not done, there may be a leakage, this situation must be checked in time, it may cause electric shock to the circuit, and it may be that the weather is too humid, there is not much sunlight, the wooden board has been kept in a humid state, and the floor is easy to mold in these cases.

  7. Anonymous users2024-02-06

    It may be because when choosing the floor, I chose some of the quality is not particularly good, and it may also be because when the installation is not secure, often waterlogged, and no one lives in it.

  8. Anonymous users2024-02-05

    It may be that the material of the floor is not very good, and it is not dried in time after installation, so there will be mold.

  9. Anonymous users2024-02-04

    It may be that the room is too damp, or there is often water on the floor, or it may not be cleaned, which can lead to mold.

  10. Anonymous users2024-02-03

    Wood flooring is a common material used in home decoration, and if it is not properly handled during cleaning, it will become moldy. So how to deal with mold on wooden floors? What are the causes of mold on wooden floors? Let's talk about it today.

    1. How to deal with moldy wood floors.

    1. The surface layer is moldy.

    Simple surface mold can be cleaned with homemade detergent, mixed with warm bleach and water in a ratio of 1:3, and wiped with a soft cloth dipped in detergent on the moldy area. If the surface layer of the severe point is moldy, it is necessary to sand the moldy area with sandpaper, remove the mold, and then repaint.

    2. Internal mold.

    If it is moldy inside, there is really no way, you can only spend a lot of money to replace the moldy floor, you must know that living in a moldy space for a long time is also very harmful to the body.

    Second, the cause of mold on the wooden floor.

    1. The mop is too wet and not wrung out during daily cleaning.

    Wood is afraid of water, and so is wood flooring. Usually, if the mop is not wrung out when cleaning, the water will flow down the cracks in the floor, and the moisture will accumulate deep in the floor for a long time and will not be dried, which will cause mold and bacteria.

    2. The water sprinkled on the floor is not wiped clean in time.

    If there is a bear child at home, you should pay more attention to the wooden floor, once the water is sprinkled on the floor and is not cleaned in time, it will seep into the inside of the floor, and the floor with moisture is of course easy to mold and black.

    3. The floor has been soaked in water, and the drying is not complete in the later stage.

    It is not uncommon for the floor to forget to turn off the faucet at home, but once the floor is soaked in water, it is easy to get damp and moldy if it is not treated in time. Many friends also just wipe the surface moisture dry, ignoring the internal moisture. It is recommended that once the plank has been soaked in water, the plank should be removed, the floor should be dried, and the floor and wall should be dried.

    4. Lay the floor before the ground is dry.

    In order to rush the work, many people lay the floor when the ground is not yet dry, which leads to the accumulation of water vapor inside, which cannot be released and can only be released through the gaps in the wall, which will cause the splicing of the floor and the wall to become moldy and black.

    In general, mold on wood floors is actually a common phenomenon. Paying more attention to the above matters in our daily life can better prevent mold on wood floors.

  11. Anonymous users2024-02-02

    Summary. 2.There's mold inside.

    If the situation is severe, the interior is moldy, and the moldy floor can only be partially replaced. Moldy wood floors that have been moldy for a long time can cause a lot of damage to the human body, so there must be no luck.

    2. Is moldy wood flooring harmful to the body?

    1.When a wood floor becomes moldy, the spore powder produced by the mold floats in the air. Long-term inhalation can cause respiratory diseases and allergic symptoms.

    Can you still use it if there is mold under the wooden floor.

    2.If the situation is severe, the moldy inside, the moldy floor can only be partially replaced. Moldy wood floors that have been moldy for a long time can cause a lot of damage to the human body, so there must be no luck.

    Second, is moldy wood flooring harmful to the body 1When a wood floor becomes moldy, the spore powder produced by the mold floats in the air. Long-term inhalation can cause respiratory diseases and allergic symptoms.

    Do you have any questions, I hope mine is helpful to you, hard work, give a thumbs up

Related questions
21 answers2024-07-06

Hello: Engine oil is equivalent to the "blood" in the automobile engine, which flows between the engine parts, plays a lubricating role, and prevents serious wear and tear between parts and components; In addition to this most important function, it also has some "additional functions", such as cooling and cooling, cleaning and cleaning, sealing and leakage, rust and corrosion prevention, shock absorption and cushioning. The main reasons for the blackening of engine oil are as follows: >>>More

8 answers2024-07-06

1. The fewer things on the computer desktop, the better, and the more things occupy the system resources. 2. Right-click "My Computer", select "Properties", then select "Performance", click "File System" on the left, there is an "Main Purpose of This Computer (T)" option, pull down the arrow, change "Desktop" to "Network Server", and then OK. Then select "Virtual Memory" on the right, select "User-specified virtual memory settings (m)", and then change the maximum and minimum values to the value of your computer's memory multiplied by 2, for example, if it is 128 trillion memory, set it to "256", and then OK, ignore the prompt displayed, and determine that you need to restart later. >>>More

24 answers2024-07-06

Hemangioma is a congenital benign tumor or vascular malformation formed by the proliferation of angioblasts during the embryonic period, which is common in ** and soft tissues, and is more common at birth or shortly after birth. The residual embryonic angioblasts, active endothelioid germ, invade adjacent tissues to form endothelial cords, which are connected to the remaining blood vessels after catheterization to form hemangiomas, and the intratumoral blood vessels are self-contained and not connected to the surrounding blood vessels. Hemangiomas can occur throughout the body, with oral and maxillofacial hemangiomas accounting for 60% of total hemangiomas, followed by the trunk (25%) and extremities (15%). >>>More

14 answers2024-07-06

If the woman has evidence, she can file it in court and ask the party at fault for damages. >>>More

21 answers2024-07-06

Auto Shutdown Troubleshooting Methods:

1. There may be a problem with the BIOS settings, enter the BIOS to restore the default settings or take out the battery of the motherboard, reverse the buckle discharge, and wait for 5 minutes to reverse install it. Purpose: To restore the default values of the BIOS settings and eliminate the automatic reboot or shutdown of the BIOS cooling presets. >>>More